On 2016-11-24 21:45, Peter Rosin wrote:
> Untested, register offsets carefully copied from datasheets.
>
> Signed-off-by: Peter Rosin <peda@xxxxxxxxxx>
> ---
> .../devicetree/bindings/pinctrl/pinctrl-sx150x.txt | 8 +-
> drivers/pinctrl/pinctrl-sx150x.c | 98 ++++++++++++++++++++++
> 2 files changed, 104 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
> index 83f8d5c449ba..bf76867168e9 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt
> @@ -6,9 +6,13 @@ pin controller, GPIO, and interrupt bindings.
>
> Required properties:
> - compatible: should be one of :
> + "semtech,sx1501q",
> "semtech,sx1502q",
> "semtech,sx1503q",
> + "semtech,sx1504q",
> + "semtech,sx1505q",
> "semtech,sx1506q",
> + "semtech,sx1507q",
> "semtech,sx1508q",
> "semtech,sx1509q".
>
> @@ -28,7 +32,7 @@ Optional properties :
> - interrupt-controller: Marks the device as a interrupt controller.
>
> - semtech,probe-reset: Will trigger a reset of the GPIO expander on probe,
> - only for sx1508q and sx1509q
> + only for sx1507q, sx1508q and sx1509q
>
> The GPIO expander can optionally be used as an interrupt controller, in
> which case it uses the default two cell specifier.
> @@ -43,7 +47,7 @@ Optional properties for pin configuration sub-nodes:
> - bias-pull-down: pull down the pin, except the OSCIO pin
> - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin
> - drive-push-pull: drive actively high and low
> - - drive-open-drain: drive with open drain only for sx1508q and sx1509q and except the OSCIO pin
> + - drive-open-drain: drive with open drain only for sx1507q, sx1508q and sx1509q and except the OSCIO pin
> - output-low: set the pin to output mode with low level
> - output-high: set the pin to output mode with high level
>
> diff --git a/drivers/pinctrl/pinctrl-sx150x.c b/drivers/pinctrl/pinctrl-sx150x.c
> index 97df9302e84b..eb6adbbd33f0 100644
> --- a/drivers/pinctrl/pinctrl-sx150x.c
> +++ b/drivers/pinctrl/pinctrl-sx150x.c
> @@ -116,6 +116,14 @@ struct sx150x_pinctrl {
> const struct sx150x_device_data *data;
> };
>
> +static const struct pinctrl_pin_desc sx150x_4_pins[] = {
> + PINCTRL_PIN(0, "gpio0"),
> + PINCTRL_PIN(1, "gpio1"),
> + PINCTRL_PIN(2, "gpio2"),
> + PINCTRL_PIN(3, "gpio3"),
> + PINCTRL_PIN(8, "oscio"),
Should of course be:
+ PINCTRL_PIN(4, "oscio"),
If you want an updated patch, just ask...
Cheers,
Peter
> +};
> +
> static const struct pinctrl_pin_desc sx150x_8_pins[] = {
> PINCTRL_PIN(0, "gpio0"),
> PINCTRL_PIN(1, "gpio1"),
> @@ -148,6 +156,26 @@ static const struct pinctrl_pin_desc sx150x_16_pins[] = {
> PINCTRL_PIN(16, "oscio"),
> };
>
> +static const struct sx150x_device_data sx1501q_device_data = {
> + .model = SX150X_123,
> + .reg_pullup = 0x02,
> + .reg_pulldn = 0x03,
> + .reg_dir = 0x01,
> + .reg_data = 0x00,
> + .reg_irq_mask = 0x05,
> + .reg_irq_src = 0x08,
> + .reg_sense = 0x07,
> + .pri.x123 = {
> + .reg_pld_mode = 0x10,
> + .reg_pld_table0 = 0x11,
> + .reg_pld_table2 = 0x13,
> + .reg_advance = 0xad,
> + },
> + .ngpios = 4,
> + .pins = sx150x_4_pins,
> + .npins = 4, /* oscio not available */
> +};
> +
> static const struct sx150x_device_data sx1502q_device_data = {
> .model = SX150X_123,
> .reg_pullup = 0x02,
> @@ -194,6 +222,47 @@ static const struct sx150x_device_data sx1503q_device_data = {
> .npins = 16, /* oscio not available */
> };
>
> +static const struct sx150x_device_data sx1504q_device_data = {
> + .model = SX150X_456,
> + .reg_pullup = 0x02,
> + .reg_pulldn = 0x03,
> + .reg_dir = 0x01,
> + .reg_data = 0x00,
> + .reg_irq_mask = 0x05,
> + .reg_irq_src = 0x08,
> + .reg_sense = 0x07,
> + .pri.x456 = {
> + .reg_pld_mode = 0x10,
> + .reg_pld_table0 = 0x11,
> + .reg_pld_table2 = 0x13,
> + },
> + .ngpios = 4,
> + .pins = sx150x_4_pins,
> + .npins = 4, /* oscio not available */
> +};
> +
> +static const struct sx150x_device_data sx1505q_device_data = {
> + .model = SX150X_456,
> + .reg_pullup = 0x02,
> + .reg_pulldn = 0x03,
> + .reg_dir = 0x01,
> + .reg_data = 0x00,
> + .reg_irq_mask = 0x05,
> + .reg_irq_src = 0x08,
> + .reg_sense = 0x06,
> + .pri.x456 = {
> + .reg_pld_mode = 0x10,
> + .reg_pld_table0 = 0x11,
> + .reg_pld_table1 = 0x12,
> + .reg_pld_table2 = 0x13,
> + .reg_pld_table3 = 0x14,
> + .reg_pld_table4 = 0x15,
> + },
> + .ngpios = 8,
> + .pins = sx150x_8_pins,
> + .npins = 8, /* oscio not available */
> +};
> +
> static const struct sx150x_device_data sx1506q_device_data = {
> .model = SX150X_456,
> .reg_pullup = 0x04,
> @@ -217,6 +286,27 @@ static const struct sx150x_device_data sx1506q_device_data = {
> .npins = 16, /* oscio not available */
> };
>
> +static const struct sx150x_device_data sx1507q_device_data = {
> + .model = SX150X_789,
> + .reg_pullup = 0x03,
> + .reg_pulldn = 0x04,
> + .reg_dir = 0x07,
> + .reg_data = 0x08,
> + .reg_irq_mask = 0x09,
> + .reg_irq_src = 0x0b,
> + .reg_sense = 0x0a,
> + .pri.x789 = {
> + .reg_drain = 0x05,
> + .reg_polarity = 0x06,
> + .reg_clock = 0x0d,
> + .reg_misc = 0x0e,
> + .reg_reset = 0x7d,
> + },
> + .ngpios = 4,
> + .pins = sx150x_4_pins,
> + .npins = ARRAY_SIZE(sx150x_4_pins),
> +};
> +
> static const struct sx150x_device_data sx1508q_device_data = {
> .model = SX150X_789,
> .reg_pullup = 0x03,
> @@ -758,18 +848,26 @@ static const struct pinconf_ops sx150x_pinconf_ops = {
> };
>
> static const struct i2c_device_id sx150x_id[] = {
> + {"sx1501q", (kernel_ulong_t) &sx1501q_device_data },
> {"sx1502q", (kernel_ulong_t) &sx1502q_device_data },
> {"sx1503q", (kernel_ulong_t) &sx1503q_device_data },
> + {"sx1504q", (kernel_ulong_t) &sx1504q_device_data },
> + {"sx1505q", (kernel_ulong_t) &sx1505q_device_data },
> {"sx1506q", (kernel_ulong_t) &sx1506q_device_data },
> + {"sx1507q", (kernel_ulong_t) &sx1507q_device_data },
> {"sx1508q", (kernel_ulong_t) &sx1508q_device_data },
> {"sx1509q", (kernel_ulong_t) &sx1509q_device_data },
> {}
> };
>
> static const struct of_device_id sx150x_of_match[] = {
> + { .compatible = "semtech,sx1501q", .data = &sx1501q_device_data },
> { .compatible = "semtech,sx1502q", .data = &sx1502q_device_data },
> { .compatible = "semtech,sx1503q", .data = &sx1503q_device_data },
> + { .compatible = "semtech,sx1504q", .data = &sx1504q_device_data },
> + { .compatible = "semtech,sx1505q", .data = &sx1505q_device_data },
> { .compatible = "semtech,sx1506q", .data = &sx1506q_device_data },
> + { .compatible = "semtech,sx1507q", .data = &sx1507q_device_data },
> { .compatible = "semtech,sx1508q", .data = &sx1508q_device_data },
> { .compatible = "semtech,sx1509q", .data = &sx1509q_device_data },
> {},
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
