[PATCH v3] ARM: at91/dt: add dts file for sama5d36ek CMP board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts is
listed as below.
 1. The USB host nodes are removed, that is, the USB host is disabled.
 2. The gpio_keys node is added to wake up from the sleep.
 3. The LCD isn't supported due to the pins for LCD are conflicted
    with gpio_keys.
 4. The adc0 node support the pinctrl sleep state to fix the over
    consumption on VDDANA.

As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.

Signed-off-by: Wenyou Yang <wenyou.yang@xxxxxxxxx>
---

Changes in v3:
 - Use a dual license scheme for DT files.
 - Use the proper model name and the compatible string to reflect
   the nature of this new "CMP" board.
 - Change name of wakeup property to "wakeup-source".
 - Remove unnecessary comments.
 - Remove bootargs.

Changes in v2:
 - Add the pinctrl sleep state for adc0 node to fix the over
   consumption on VDDANA.
 - Improve the commit log.

 arch/arm/boot/dts/sama5d36ek_cmp.dts  |  87 ++++++++++
 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 201 +++++++++++++++++++++++
 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 301 ++++++++++++++++++++++++++++++++++
 3 files changed, 589 insertions(+)
 create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
 create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
 create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi

diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
new file mode 100644
index 0000000..b632143
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
@@ -0,0 +1,87 @@
+/*
+ * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+#include "sama5d3xmb_cmp.dtsi"
+
+/ {
+	model = "Atmel SAMA5D36EK-CMP";
+	compatible = "atmel,sama5d36ek-cmp", "atmel,sama5d3xmb-cmp", "atmel,sama5d3xcm-cmp", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+	ahb {
+		apb {
+			spi0: spi@f0004000 {
+				status = "okay";
+			};
+
+			ssc0: ssc@f0008000 {
+				status = "okay";
+			};
+
+			can0: can@f000c000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@f0014000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@f0018000 {
+				status = "okay";
+			};
+
+			macb0: ethernet@f0028000 {
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				status = "okay";
+			};
+		};
+	};
+
+	sound {
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
new file mode 100644
index 0000000..dc7572b
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
@@ -0,0 +1,201 @@
+/*
+ * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+	compatible = "atmel,sama5d3xcm-cmp", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x20000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+			};
+
+			macb0: ethernet@f0028000 {
+				phy-mode = "rgmii";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioB>;
+					interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+					txen-skew-ps = <800>;
+					txc-skew-ps = <3000>;
+					rxdv-skew-ps = <400>;
+					rxc-skew-ps = <3000>;
+					rxd0-skew-ps = <400>;
+					rxd1-skew-ps = <400>;
+					rxd2-skew-ps = <400>;
+					rxd3-skew-ps = <400>;
+				};
+
+				ethernet-phy@7 {
+					reg = <0x7>;
+					interrupt-parent = <&pioB>;
+					interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+					txen-skew-ps = <800>;
+					txc-skew-ps = <3000>;
+					rxdv-skew-ps = <400>;
+					rxc-skew-ps = <3000>;
+					rxd0-skew-ps = <400>;
+					rxd1-skew-ps = <400>;
+					rxd2-skew-ps = <400>;
+					rxd3-skew-ps = <400>;
+				};
+			};
+
+			i2c1: i2c@f0018000 {
+				pmic: act8865@5b {
+					compatible = "active-semi,act8865";
+					reg = <0x5b>;
+					status = "disabled";
+
+					regulators {
+						vcc_1v8_reg: DCDC_REG1 {
+							regulator-name = "VCC_1V8";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <1800000>;
+							regulator-always-on;
+						};
+
+						vcc_1v2_reg: DCDC_REG2 {
+							regulator-name = "VCC_1V2";
+							regulator-min-microvolt = <1100000>;
+							regulator-max-microvolt = <1300000>;
+							regulator-always-on;
+						};
+
+						vcc_3v3_reg: DCDC_REG3 {
+							regulator-name = "VCC_3V3";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						vddana_reg: LDO_REG1 {
+							regulator-name = "VDDANA";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						vddfuse_reg: LDO_REG2 {
+							regulator-name = "FUSE_2V5";
+							regulator-min-microvolt = <2500000>;
+							regulator-max-microvolt = <2500000>;
+						};
+					};
+				};
+			};
+		};
+
+		nand0: nand@60000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader@40000 {
+				label = "bootloader";
+				reg = <0x40000 0x80000>;
+			};
+
+			bootloaderenv@c0000 {
+				label = "bootloader env";
+				reg = <0xc0000 0xc0000>;
+			};
+
+			dtb@180000 {
+				label = "device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x200000 0x600000>;
+			};
+
+			rootfs@800000 {
+				label = "rootfs";
+				reg = <0x800000 0x0f800000>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		d2 {
+			label = "d2";
+			gpios = <&pioE 25 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000..252e0d3
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,301 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+	compatible = "atmel,sama5d3xmb-cmp", "atmel,sama5d3xcm-cmp", "atmel,sama5d3", "atmel,sama5";
+
+	ahb {
+		apb {
+			mmc0: mmc@f0000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			spi0: spi@f0004000 {
+				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
+
+				m25p80@0 {
+					compatible = "atmel,at25df321a";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			ssc0: ssc@f0008000 {
+				atmel,clk-from-rk-pin;
+			};
+
+			/*
+			 * i2c0 conflicts with ISI:
+			 * disable it to allow the use of ISI
+			 * can not enable audio when i2c0 disabled
+			 */
+			i2c0: i2c@f0014000 {
+				wm8904: wm8904@1a {
+					compatible = "wlf,wm8904";
+					reg = <0x1a>;
+					clocks = <&pck0>;
+					clock-names = "mclk";
+				};
+			};
+
+			i2c1: i2c@f0018000 {
+				ov2640: camera@0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+					/* use pck1 for the master clock of ov2640 */
+					clocks = <&pck1>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck1>;
+					assigned-clock-rates = <25000000>;
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
+			};
+
+			usart1: serial@f0020000 {
+				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+				status = "okay";
+			};
+
+			isi: isi@f0034000 {
+				port {
+					isi_0: endpoint {
+						remote-endpoint = <&ov2640_0>;
+						bus-width = <8>;
+						vsync-active = <1>;
+						hsync-active = <1>;
+					};
+				};
+			};
+
+			mmc1: mmc@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			adc0: adc@f8018000 {
+				pinctrl-names = "default", "sleep";
+				pinctrl-0 = <
+					&pinctrl_adc0_adtrg
+					&pinctrl_adc0_ad0
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					>;
+				pinctrl-1 = <
+					&pinctrl_adc0_adtrg_sleep
+					&pinctrl_adc0_ad0_sleep
+					&pinctrl_adc0_ad1_sleep
+					&pinctrl_adc0_ad2_sleep
+					&pinctrl_adc0_ad3_sleep
+					&pinctrl_adc0_ad4_sleep
+					>;
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				phy-mode = "rmii";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy0: ethernet-phy@1 {
+					/*interrupt-parent = <&pioE>;*/
+					/*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+					reg = <1>;
+				};
+			};
+
+			pinctrl@fffff200 {
+				adc0 {
+					pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
+						atmel,pins =
+							<AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
+					};
+					pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
+						atmel,pins =
+							<AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
+					};
+					pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
+						atmel,pins =
+							<AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
+					};
+					pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
+						atmel,pins =
+							<AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
+					};
+					pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
+						atmel,pins =
+							<AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
+					};
+					pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
+						atmel,pins =
+							<AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>;
+					};
+				};
+
+				board {
+					pinctrl_gpio_keys: gpio_keys {
+						atmel,pins =
+							<AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+					};
+
+					pinctrl_mmc0_cd: mmc0_cd {
+						atmel,pins =
+							<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+						atmel,pins =
+							<AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+						atmel,pins =
+							<AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_sensor_reset: sensor_reset-0 {
+						atmel,pins =
+							<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_sensor_power: sensor_power-0 {
+						atmel,pins =
+							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+					};
+				};
+			};
+
+			dbgu: serial@ffffee00 {
+				dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
+				status = "okay";
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+
+		usb0: gadget@00500000 {
+			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+	};
+
+	sound {
+		compatible = "atmel,asoc-wm8904";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+		atmel,model = "wm8904 @ SAMA5D3EK";
+		atmel,audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Mic", "MICBIAS",
+			"IN1L", "Mic";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8904>;
+
+		status = "disabled";
+	};
+
+	/* Conflict with LCD pins */
+	gpio_keys {
+		compatible = "gpio-keys";
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		pb_user1 {
+			label = "pb_user1";
+			gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x100>;
+			wakeup-source;
+		};
+	};
+};
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux