[PATCH v2] ARM: dts: sun5i: Add touchscreen node to reference-design-tablet.dtsi

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Just like on sun8i all sun5i tablets use the same interrupt and power
gpios for their touchscreens. I've checked all known a13 fex files and
only the UTOO P66 uses a different gpio for the interrupt.

Add a touchscreen node to sun5i-reference-design-tablet.dtsi, which
fills in the necessary gpios to avoid duplication in the tablet dts files,
just like we do in sun8i-reference-design-tablet.dtsi.

This will make future patches adding touchscreen nodes to a13 tablets
simpler.

Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
Changes in v2:
-Use generic pin mux properties "pins", "function", "drive-strength" and
 "bias-disable"
---
 arch/arm/boot/dts/sun5i-a13-utoo-p66.dts           | 38 ++++++++--------------
 .../boot/dts/sun5i-reference-design-tablet.dtsi    | 25 ++++++++++++++
 2 files changed, 39 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
index a8b0bcc..3d7ff10 100644
--- a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
+++ b/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
@@ -83,22 +83,6 @@
 	allwinner,pins = "PG3";
 };
 
-&i2c1 {
-	icn8318: touchscreen@40 {
-		compatible = "chipone,icn8318";
-		reg = <0x40>;
-		interrupt-parent = <&pio>;
-		interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_wake_pin_p66>;
-		wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
-		touchscreen-inverted-x;
-		touchscreen-swapped-x-y;
-	};
-};
-
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins_a>;
@@ -121,20 +105,26 @@
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
-
-	ts_wake_pin_p66: ts_wake_pin@0 {
-		allwinner,pins = "PB3";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
 };
 
 &reg_usb0_vbus {
 	gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
 };
 
+&touchscreen {
+	compatible = "chipone,icn8318";
+	reg = <0x40>;
+	/* The P66 uses a different EINT then the reference design */
+	interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
+	/* The icn8318 binding expects wake-gpios instead of power-gpios */
+	wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+	touchscreen-size-x = <800>;
+	touchscreen-size-y = <480>;
+	touchscreen-inverted-x;
+	touchscreen-swapped-x-y;
+	status = "okay";
+};
+
 &uart1 {
 	/* The P66 uses the uart pins as gpios */
 	status = "disabled";
diff --git a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
index 20cc940..82f87cd 100644
--- a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
@@ -41,6 +41,7 @@
  */
 #include "sunxi-reference-design-tablet.dtsi"
 
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 
 / {
@@ -84,6 +85,23 @@
 };
 
 &i2c1 {
+	/*
+	 * The gsl1680 is rated at 400KHz and it will not work reliable at
+	 * 100KHz, this has been confirmed on multiple different q8 tablets.
+	 * All other devices on this bus are also rated for 400KHz.
+	 */
+	clock-frequency = <400000>;
+
+	touchscreen: touchscreen {
+		interrupt-parent = <&pio>;
+		interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_power_pin>;
+		power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+		/* Tablet dts must provide reg and compatible */
+		status = "disabled";
+	};
+
 	pcf8563: rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
@@ -125,6 +143,13 @@
 		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
 
+	ts_power_pin: ts_power_pin {
+		pins = "PB3";
+		function = "gpio_out";
+		drive-strength = <10>;
+		bias-disable;
+	};
+
 	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
 		allwinner,pins = "PG1";
 		allwinner,function = "gpio_in";
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux