On Mon, Nov 14, 2016 at 11:15:54AM +0000, Srinivas Kandagatla wrote:
> This patch adds support to msm8996/apq8096 pcie, MSM8996 supports
> Gen 1/2, One lane, 3 pcie root-complex with support to MSI and
> legacy interrupts and it conforms to PCI Express Base 2.1 specification.
>
> This patch adds post_init callback to qcom_pcie_ops, as this is pcie
> pipe clocks are only setup after the phy is powered on.
> It also adds ltssm_enable callback as it is very much different to other
> supported SOCs in the driver.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
Will need ack from Stanimir before I can apply it.
> ---
> .../devicetree/bindings/pci/qcom,pcie.txt | 67 +++++++-
> drivers/pci/host/pcie-qcom.c | 177 ++++++++++++++++++++-
> 2 files changed, 238 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> index 4059a6f..141d8c3 100644
> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> @@ -7,6 +7,7 @@
> - "qcom,pcie-ipq8064" for ipq8064
> - "qcom,pcie-apq8064" for apq8064
> - "qcom,pcie-apq8084" for apq8084
> + - "qcom,pcie-msm8996" for msm8996 or apq8096
>
> - reg:
> Usage: required
> @@ -92,6 +93,17 @@
> - "aux" Auxiliary (AUX) clock
> - "bus_master" Master AXI clock
> - "bus_slave" Slave AXI clock
> +
> +- clock-names:
> + Usage: required for msm8996/apq8096
> + Value type: <stringlist>
> + Definition: Should contain the following entries
> + - "pipe" Pipe Clock driving internal logic.
> + - "aux" Auxiliary (AUX) clock.
> + - "cfg" Configuration clk.
> + - "bus_master" Master AXI clock.
> + - "bus_slave" Slave AXI clock.
> +
> - resets:
> Usage: required
> Value type: <prop-encoded-array>
> @@ -115,7 +127,7 @@
> - "core" Core reset
>
> - power-domains:
> - Usage: required for apq8084
> + Usage: required for apq8084 and msm8996/apq8096
> Value type: <prop-encoded-array>
> Definition: A phandle and power domain specifier pair to the
> power domain which is responsible for collapsing
> @@ -231,3 +243,56 @@
> pinctrl-0 = <&pcie0_pins_default>;
> pinctrl-names = "default";
> };
> +
> +* Example for apq8096:
> +
> + pcie@608000{
> + compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
> + power-domains = <&gcc PCIE1_GDSC>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> +
> + reg = <0x00608000 0x2000>,
> + <0x0d000000 0xf1d>,
> + <0x0d000f20 0xa8>,
> + <0x0d100000 0x100000>;
> +
> + reg-names = "parf", "dbi", "elbi", "config";
> +
> + phys = <&pcie_phy 1>;
> + phy-names = "pciephy";
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>,
> + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
> +
> + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
> + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
> +
> + vdda-1p8-supply = <&pm8994_l12>;
> + vdda-supply = <&pm8994_l28>;
> + linux,pci-domain = <1>;
> +
> + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
> + <&gcc GCC_PCIE_1_AUX_CLK>,
> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_1_SLV_AXI_CLK>;
> +
> + clock-names = "pipe",
> + "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave";
> + };
> diff --git a/drivers/pci/host/pcie-qcom.c b/drivers/pci/host/pcie-qcom.c
> index 3593640..03ba6b1 100644
> --- a/drivers/pci/host/pcie-qcom.c
> +++ b/drivers/pci/host/pcie-qcom.c
> @@ -36,11 +36,19 @@
>
> #include "pcie-designware.h"
>
> +#define PCIE20_PARF_DBI_BASE_ADDR 0x168
> +
> +#define PCIE20_PARF_SYS_CTRL 0x00
> #define PCIE20_PARF_PHY_CTRL 0x40
> #define PCIE20_PARF_PHY_REFCLK 0x4C
> #define PCIE20_PARF_DBI_BASE_ADDR 0x168
> #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16c
> +#define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174
> #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x178
> +#define MSM8996_PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x1A8
> +#define PCIE20_PARF_LTSSM 0x1B0
> +#define PCIE20_PARF_SID_OFFSET 0x234
> +#define PCIE20_PARF_BDF_TRANSLATE_CFG 0x24C
>
> #define PCIE20_ELBI_SYS_CTRL 0x04
> #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE BIT(0)
> @@ -72,9 +80,18 @@ struct qcom_pcie_resources_v1 {
> struct regulator *vdda;
> };
>
> +struct qcom_pcie_resources_v2 {
> + struct clk *aux_clk;
> + struct clk *master_clk;
> + struct clk *slave_clk;
> + struct clk *cfg_clk;
> + struct clk *pipe_clk;
> +};
> +
> union qcom_pcie_resources {
> struct qcom_pcie_resources_v0 v0;
> struct qcom_pcie_resources_v1 v1;
> + struct qcom_pcie_resources_v2 v2;
> };
>
> struct qcom_pcie;
> @@ -82,7 +99,9 @@ struct qcom_pcie;
> struct qcom_pcie_ops {
> int (*get_resources)(struct qcom_pcie *pcie);
> int (*init)(struct qcom_pcie *pcie);
> + int (*post_init)(struct qcom_pcie *pcie);
> void (*deinit)(struct qcom_pcie *pcie);
> + void (*ltssm_enable)(struct qcom_pcie *pcie);
> };
>
> struct qcom_pcie {
> @@ -116,17 +135,33 @@ static irqreturn_t qcom_pcie_msi_irq_handler(int irq, void *arg)
> return dw_handle_msi_irq(pp);
> }
>
> -static int qcom_pcie_establish_link(struct qcom_pcie *pcie)
> +static void qcom_pcie_v0_v1_ltssm_enable(struct qcom_pcie *pcie)
> {
> u32 val;
> -
> - if (dw_pcie_link_up(&pcie->pp))
> - return 0;
> -
> /* enable link training */
> val = readl(pcie->elbi + PCIE20_ELBI_SYS_CTRL);
> val |= PCIE20_ELBI_SYS_CTRL_LT_ENABLE;
> writel(val, pcie->elbi + PCIE20_ELBI_SYS_CTRL);
> +}
> +
> +static void qcom_pcie_v2_ltssm_enable(struct qcom_pcie *pcie)
> +{
> + u32 val;
> + /* enable link training */
> + val = readl(pcie->parf + PCIE20_PARF_LTSSM);
> + val |= BIT(8);
> + writel(val, pcie->parf + PCIE20_PARF_LTSSM);
> +}
> +
> +static int qcom_pcie_establish_link(struct qcom_pcie *pcie)
> +{
> +
> + if (dw_pcie_link_up(&pcie->pp))
> + return 0;
> +
> + /* Enable Link Training state machine */
> + if (pcie->ops->ltssm_enable)
> + pcie->ops->ltssm_enable(pcie);
>
> return dw_pcie_wait_for_link(&pcie->pp);
> }
> @@ -421,6 +456,113 @@ static int qcom_pcie_init_v1(struct qcom_pcie *pcie)
> return ret;
> }
>
> +static int qcom_pcie_get_resources_v2(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
> + struct device *dev = pcie->pp.dev;
> +
> + res->aux_clk = devm_clk_get(dev, "aux");
> + if (IS_ERR(res->aux_clk))
> + return PTR_ERR(res->aux_clk);
> +
> + res->cfg_clk = devm_clk_get(dev, "cfg");
> + if (IS_ERR(res->cfg_clk))
> + return PTR_ERR(res->cfg_clk);
> +
> + res->master_clk = devm_clk_get(dev, "bus_master");
> + if (IS_ERR(res->master_clk))
> + return PTR_ERR(res->master_clk);
> +
> + res->slave_clk = devm_clk_get(dev, "bus_slave");
> + if (IS_ERR(res->slave_clk))
> + return PTR_ERR(res->slave_clk);
> +
> + res->pipe_clk = devm_clk_get(dev, "pipe");
> + if (IS_ERR(res->pipe_clk))
> + return PTR_ERR(res->pipe_clk);
> +
> + return 0;
> +}
> +
> +static int qcom_pcie_init_v2(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
> + struct device *dev = pcie->pp.dev;
> + u32 val;
> + int ret;
> +
> + ret = clk_prepare_enable(res->aux_clk);
> + if (ret) {
> + dev_err(dev, "cannot prepare/enable aux clock\n");
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(res->cfg_clk);
> + if (ret) {
> + dev_err(dev, "cannot prepare/enable cfg clock\n");
> + goto err_cfg_clk;
> + }
> +
> + ret = clk_prepare_enable(res->master_clk);
> + if (ret) {
> + dev_err(dev, "cannot prepare/enable master clock\n");
> + goto err_master_clk;
> + }
> +
> + ret = clk_prepare_enable(res->slave_clk);
> + if (ret) {
> + dev_err(dev, "cannot prepare/enable slave clock\n");
> + goto err_slave_clk;
> + }
> +
> + /* enable PCIe clocks and resets */
> + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> + val &= ~BIT(0);
> + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> + /* change DBI base address */
> + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> +
> + /* MAC PHY_POWERDOWN MUX DISABLE */
> + val = readl(pcie->parf + PCIE20_PARF_SYS_CTRL);
> + val &= ~BIT(29);
> + writel(val, pcie->parf + PCIE20_PARF_SYS_CTRL);
> +
> + val = readl(pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> + val |= BIT(4);
> + writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +
> + val = readl(pcie->parf + MSM8996_PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT);
> + val |= BIT(31);
> + writel(val, pcie->parf + MSM8996_PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT);
> +
> + return 0;
> +
> +err_slave_clk:
> + clk_disable_unprepare(res->master_clk);
> +err_master_clk:
> + clk_disable_unprepare(res->cfg_clk);
> +err_cfg_clk:
> + clk_disable_unprepare(res->aux_clk);
> +
> + return ret;
> +}
> +
> +static int qcom_pcie_post_init_v2(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
> + struct device *dev = pcie->pp.dev;
> + int ret;
> +
> + ret = clk_prepare_enable(res->pipe_clk);
> + if (ret) {
> + dev_err(dev, "cannot prepare/enable pipe clock\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> static int qcom_pcie_link_up(struct pcie_port *pp)
> {
> struct qcom_pcie *pcie = to_qcom_pcie(pp);
> @@ -429,6 +571,17 @@ static int qcom_pcie_link_up(struct pcie_port *pp)
> return !!(val & PCI_EXP_LNKSTA_DLLLA);
> }
>
> +static void qcom_pcie_deinit_v2(struct qcom_pcie *pcie)
> +{
> + struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
> +
> + clk_disable_unprepare(res->pipe_clk);
> + clk_disable_unprepare(res->slave_clk);
> + clk_disable_unprepare(res->master_clk);
> + clk_disable_unprepare(res->cfg_clk);
> + clk_disable_unprepare(res->aux_clk);
> +}
> +
> static void qcom_pcie_host_init(struct pcie_port *pp)
> {
> struct qcom_pcie *pcie = to_qcom_pcie(pp);
> @@ -444,6 +597,9 @@ static void qcom_pcie_host_init(struct pcie_port *pp)
> if (ret)
> goto err_deinit;
>
> + if (pcie->ops->post_init)
> + pcie->ops->post_init(pcie);
> +
> dw_pcie_setup_rc(pp);
>
> if (IS_ENABLED(CONFIG_PCI_MSI))
> @@ -487,12 +643,22 @@ static const struct qcom_pcie_ops ops_v0 = {
> .get_resources = qcom_pcie_get_resources_v0,
> .init = qcom_pcie_init_v0,
> .deinit = qcom_pcie_deinit_v0,
> + .ltssm_enable = qcom_pcie_v0_v1_ltssm_enable,
> };
>
> static const struct qcom_pcie_ops ops_v1 = {
> .get_resources = qcom_pcie_get_resources_v1,
> .init = qcom_pcie_init_v1,
> .deinit = qcom_pcie_deinit_v1,
> + .ltssm_enable = qcom_pcie_v0_v1_ltssm_enable,
> +};
> +
> +static const struct qcom_pcie_ops ops_v2 = {
> + .get_resources = qcom_pcie_get_resources_v2,
> + .init = qcom_pcie_init_v2,
> + .post_init = qcom_pcie_post_init_v2,
> + .deinit = qcom_pcie_deinit_v2,
> + .ltssm_enable = qcom_pcie_v2_ltssm_enable,
> };
>
> static int qcom_pcie_probe(struct platform_device *pdev)
> @@ -572,6 +738,7 @@ static const struct of_device_id qcom_pcie_match[] = {
> { .compatible = "qcom,pcie-ipq8064", .data = &ops_v0 },
> { .compatible = "qcom,pcie-apq8064", .data = &ops_v0 },
> { .compatible = "qcom,pcie-apq8084", .data = &ops_v1 },
> + { .compatible = "qcom,pcie-msm8996", .data = &ops_v2 },
> { }
> };
>
> --
> 2.10.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
