Re: [PATCH 2/2] pinctrl: tegra: Add driver to configure voltage and power of io pads

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On Tuesday 08 November 2016 03:45 PM, Linus Walleij wrote:
On Mon, Nov 7, 2016 at 6:41 AM, Laxman Dewangan <ldewangan@xxxxxxxxxx> wrote:
On Saturday 05 November 2016 03:54 AM, Linus Walleij wrote:
On Wed, Nov 2, 2016 at 10:09 AM, Laxman Dewangan <ldewangan@xxxxxxxxxx>
(....)
On Tegra124, the IO power rail source is auto detected by SoC and hence
it is only require to configure in low power mode if IO pads are not
used.

On T210 onwards, the auto-detection is removed from SoC and hence SW
must configure the PMC register explicitly to set proper voltage in
IO pads based on IO rail power source voltage.
(...)
+static const struct pinconf_generic_params tegra_io_pads_cfg_params[] =
{
+       {
+               .property = "nvidia,power-source-voltage",
+               .param = TEGRA_IO_PAD_POWER_SOURCE_VOLTAGE,
+       },
+};
Why can you not use the standard power-source binding
from Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
instead of inventing this nvidia,* variant?

Per binding doc,
power-source            - select between different power supplies

So actually it selects the different source of power supply.
In my case, I will have same supply but voltage of that supply get changed.
So here property is for the power-supply-voltage.
I doubt that seriously. Are you sure? Then the commit message is
misleading because it is talking about different power rails.
The set of pins belongs to the IO pad group and this pad group has power supply from external PMIC. The IO pads support multi-level voltage and the level need to be configured in the PMIC rail via regulator calls and the IO pads configuration register for that level.


The usual design of such IP is that there is a switch that select
a voltage from several available rails and this is what the commit
message seems to be saying, and that is what the binding is for.

There is no switch to select the power source inside IP. We have only one source for supply these pins (IO pads) and the source voltage can be change here.


If you could actually change the voltage it would change for all
other pins using the same voltage source as well, would it not?
There is grouping of pins based on interface and yes, voltage level gets changed for those group of pins. Like form SDMMC interface all data nd clock lines, for i2c SCL and SDA lines etc. The HW IP design is like that from single IO voltage source, all pins are affected.



Unless there is one voltage regulator per pin, which seems like
a very expensive and chip surface consuming solution. (Albeit
theoretically possible.)

If you can *actually* change the volatage, it needs to be modeled
as a (fixed voltage?) regulator, not as a custom property for the pin
control attributes. I guess you definiately need the regulator framework
to accumulate and infer the different consumer requirements anyway
in that case.

The PMIC voltage output is changed via regulator calls.
Here, we need to have two configruations for given voltage level of interface: * One at IO voltage from PMIC via regulator call to change votlage of IO rail. * Second, configure the IO pad register to tell the IO voltage level so that it can configured internally for that level.

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux