[PATCH 5/10] dt: bindings: Add bindings for Marvell Xenon SD Host Controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




From: Ziji Hu <huziji@xxxxxxxxxxx>

Marvell Xenon SDHC can support eMMC/SD/SDIO.
Add Xenon-specific properties.
Also add properties for Xenon PHY setting.

Signed-off-by: Hu Ziji <huziji@xxxxxxxxxxx>
Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx>
---
 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt | 161 +++++++-
 MAINTAINERS                                                   |   1 +-
 2 files changed, 162 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt

diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
new file mode 100644
index 000000000000..0d2d139494d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
@@ -0,0 +1,161 @@
+Marvell's Xenon SDHCI Controller device tree bindings
+This file documents differences between the core mmc properties
+described by mmc.txt and the properties used by the Xenon implementation.
+
+A single Xenon IP can support multiple slots.
+Each slot acts as an independent SDHC. It owns independent resources, such
+as register sets clock and PHY.
+Each slot should have an independent device tree node.
+
+Required Properties:
+- compatible: should be one of the following
+  - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SOC.
+  Must provide a second register area and marvell,pad-type.
+  - "marvell,xenon-sdhci": For controllers on all the SOCs, other than
+  Armada-3700.
+
+- clocks:
+  Array of clocks required for SDHCI.
+  Requires at least one for Xenon IP core.
+  Some SOCs require additional clock for AXI bus.
+
+- clock-names:
+  Array of names corresponding to clocks property.
+  The input clock for Xenon IP core should be named as "core".
+  The optional AXI clock should be named as "axi".
+
+- reg:
+  * For "marvell,xenon-sdhci", one register area for Xenon IP.
+
+  * For "marvell,armada-3700-sdhci", two register areas.
+    The first one for Xenon IP register. The second one for the Armada 3700 SOC
+    PHY PAD Voltage Control register.
+    Please follow the examples with compatible "marvell,armada-3700-sdhci"
+    in below.
+    Please also check property marvell,pad-type in below.
+
+Optional Properties:
+- marvell,xenon-slotno:
+  Indicate the corresponding bit index of current Xenon SDHC slot in
+  SDHC System Operation Control Register Bit[7:0].
+  Set/clear the corresponding bit to enable/disable current Xenon SDHC
+  slot.
+  If this property is not provided, Xenon IP should contain only one
+  slot.
+
+- marvell,xenon-phy-type:
+  Xenon support mutilple types of PHYs.
+  To select eMMC 5.1 PHY, set:
+  marvell,xenon-phy-type = "emmc 5.1 phy"
+  eMMC 5.1 PHY is the default choice if this property is not provided.
+  To select eMMC 5.0 PHY, set:
+  marvell,xenon-phy-type = "emmc 5.0 phy"
+  To select SDH PHY, set:
+  marvell,xenon-phy-type = "sdh phy"
+  Please note that eMMC PHY is a general PHY for eMMC/SD/SDIO, other than for
+  eMMC only.
+
+- marvell,xenon-phy-znr:
+  Set PHY ZNR value.
+  Only available for eMMC PHY 5.1 and eMMC PHY 5.0.
+  valid range = [0:0x1F].
+  ZNR is set as 0xF by default if this property is not provided.
+
+- marvell,xenon-phy-zpr:
+  Set PHY ZPR value.
+  Only available for eMMC PHY 5.1 and eMMC PHY 5.0.
+  valid range = [0:0x1F].
+  ZPR is set as 0xF by default if this property is not provided.
+
+- marvell,xenon-phy-nr-success-tun:
+  Set the number of required consecutive successful sampling points used to
+  identify a valid sampling window, in tuning process.
+  Valid range = [1:7]. Set as 0x4 by default if this property is not provided.
+
+- marvell,xenon-phy-tun-step-divider:
+  Set the divider for calculating TUN_STEP.
+  Set as 64 by default if this property is not provided.
+
+- marvell,xenon-phy-slow-mode:
+  Force PHY into slow mode.
+  Only available when bus frequency lower than 50MHz in SDR mde.
+  Disabled by default. Please do not enable it unless it is necessary.
+
+- marvell,xenon-mask-conflict-err:
+  Mask Conflict Error alert on some SOC. Disabled by default.
+
+- marvell,xenon-tun-count:
+  Xenon SDHC SOC usually doesn't provide re-tuning counter in
+  Capabilities Register 3 Bit[11:8].
+  This property provides the re-tuning counter.
+  If this property is not set, default re-tuning counter will
+  be set as 0x9 in driver.
+
+- marvell,pad-type:
+  Type of Armada 3700 SOC PHY PAD Voltiage Controller register.
+  Only valid when "marvell,armada-3700-sdhci" is selected.
+  Two types: "sd" and "fixed-1-8v".
+  If "sd" is slected, SOC PHY PAD is set as 3.3V at the beginning and is
+  switched to 1.8V when SD in UHS-I.
+  If "fixed-1-8v" is slected, SOC PHY PAD is fixed 1.8V, such as for eMMC.
+  Please follow the examples with compatible "marvell,armada-3700-sdhci"
+  in below.
+
+Example:
+- For eMMC slot:
+
+	sdhci@aa0000 {
+		compatible = "marvell,xenon-sdhci";
+		reg = <0xaa0000 0x1000>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
+		clocks = <&emmc_clk>, <&axi_clock>;
+		clock-names = "core", "axi";
+		bus-width = <8>;
+		marvell,xenon-emmc;
+		marvell,xenon-slotno = <0>;
+		marvell,xenon-phy-type = "emmc 5.1 phy";
+		marvell,xenon-tun-count = <11>;
+	};
+
+- For SD/SDIO slot:
+
+	sdhci@ab0000 {
+		compatible = "marvell,xenon-sdhci";
+		reg = <0xab0000 0x1000>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
+		vqmmc-supply = <&sd_regulator>;
+		clocks = <&sdclk>;
+		clock-names = "core";
+		bus-width = <4>;
+		marvell,xenon-tun-count = <9>;
+	};
+
+- For eMMC slot with compatible "marvell,armada-3700-sdhci":
+
+	sdhci@aa0000 {
+		compatible = "marvell,armada-3700-sdhci";
+		reg = <0xaa0000 0x1000>,
+		      <phy_addr 0x4>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
+		clocks = <&emmcclk>;
+		clock-names = "core";
+		bus-width = <8>;
+		marvell,xenon-emmc;
+
+		marvell,pad-type = "fixed-1-8v";
+	};
+
+- For SD/SDIO slot with compatible "marvell,armada-3700-sdhci":
+
+	sdhci@ab0000 {
+		compatible = "marvell,armada-3700-sdhci";
+		reg = <0xab0000 0x1000>,
+		      <phy_addr 0x4>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
+		vqmmc-supply = <&sd_regulator>;
+		clocks = <&sdclk>;
+		clock-names = "core";
+		bus-width = <4>;
+
+		marvell,pad-type = "sd";
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 1a5c4c30ea24..850a0afb0c8d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7608,6 +7608,7 @@ MARVELL XENON MMC/SD/SDIO HOST CONTROLLER DRIVER
 M:	Ziji Hu <huziji@xxxxxxxxxxx>
 L:	linux-mmc@xxxxxxxxxxxxxxx
 S:	Supported
+F:	Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
 
 MATROX FRAMEBUFFER DRIVER
 L:	linux-fbdev@xxxxxxxxxxxxxxx
-- 
git-series 0.8.10
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux