The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@xxxxxxxxx>
Cc: Mike Looijmans <mike.looijmans@xxxxxxxx>
Cc: Michael Turquette <mturquette@xxxxxxxxxx>
Cc: Stephen Boyd <sboyd@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/clock/ti,cdce925.txt | 15 ++-
drivers/clk/Kconfig | 11 ++-
drivers/clk/clk-cdce925.c | 106 ++++++++++++++++-----
3 files changed, 99 insertions(+), 33 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/ti,cdce925.txt b/Documentation/devicetree/bindings/clock/ti,cdce925.txt
index 4c7669a..0d01f2d 100644
--- a/Documentation/devicetree/bindings/clock/ti,cdce925.txt
+++ b/Documentation/devicetree/bindings/clock/ti,cdce925.txt
@@ -1,15 +1,22 @@
-Binding for TO CDCE925 programmable I2C clock synthesizers.
+Binding for TI CDCE913/925/937/949 programmable I2C clock synthesizers.
Reference
This binding uses the common clock binding[1].
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] http://www.ti.com/product/cdce925
+[2] http://www.ti.com/product/cdce913
+[3] http://www.ti.com/product/cdce925
+[4] http://www.ti.com/product/cdce937
+[5] http://www.ti.com/product/cdce949
The driver provides clock sources for each output Y1 through Y5.
Required properties:
- - compatible: Shall be "ti,cdce925"
+ - compatible: Shall be one of the following:
+ - "ti,cdce913": 1-PLL, 3 Outputs
+ - "ti,cdce925": 2-PLL, 5 Outputs
+ - "ti,cdce937": 3-PLL, 7 Outputs
+ - "ti,cdce949": 4-PLL, 9 Outputs
- reg: I2C device address.
- clocks: Points to a fixed parent clock that provides the input frequency.
- #clock-cells: From common clock bindings: Shall be 1.
@@ -18,7 +25,7 @@ Optional properties:
- xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a
board, or to compensate for external influences.
-For both PLL1 and PLL2 an optional child node can be used to specify spread
+For all PLL1, PLL2, ... an optional child node can be used to specify spread
spectrum clocking parameters for a board.
- spread-spectrum: SSC mode as defined in the data sheet.
- spread-spectrum-center: Use "centered" mode instead of "max" mode. When
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index e99a42f..bc0a6e6 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -104,16 +104,17 @@ config COMMON_CLK_CDCE706
This driver supports TI CDCE706 programmable 3-PLL clock synthesizer.
config COMMON_CLK_CDCE925
- tristate "Clock driver for TI CDCE925 devices"
+ tristate "Clock driver for TI CDCE913/925/937/949 devices"
depends on I2C
depends on OF
select REGMAP_I2C
help
---help---
- This driver supports the TI CDCE925 programmable clock synthesizer.
- The chip contains two PLLs with spread-spectrum clocking support and
- five output dividers. The driver only supports the following setup,
- and uses a fixed setting for the output muxes.
+ This driver supports the TI CDCE913/925/937/949 programmable clock
+ synthesizer. Each chip has different number of PLLs and outputs.
+ For example, the CDCE925 contains two PLLs with spread-spectrum
+ clocking support and five output dividers. The driver only supports
+ the following setup, and uses a fixed setting for the output muxes.
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
diff --git a/drivers/clk/clk-cdce925.c b/drivers/clk/clk-cdce925.c
index b8459c1..fbac08d 100644
--- a/drivers/clk/clk-cdce925.c
+++ b/drivers/clk/clk-cdce925.c
@@ -1,8 +1,8 @@
/*
- * Driver for TI Dual PLL CDCE925 clock synthesizer
+ * Driver for TI Multi PLL CDCE913/925/937/949 clock synthesizer
*
- * This driver always connects the Y1 to the input clock, Y2/Y3 to PLL1
- * and Y4/Y5 to PLL2. PLL frequency is set on a first-come-first-serve
+ * This driver always connects the Y1 to the input clock, Y2/Y3 to PLL1,
+ * Y4/Y5 to PLL2, and so on. PLL frequency is set on a first-come-first-serve
* basis. Clients can directly request any frequency that the chip can
* deliver using the standard clk framework. In addition, the device can
* be configured and activated via the devicetree.
@@ -19,11 +19,32 @@
#include <linux/slab.h>
#include <linux/gcd.h>
-/* The chip has 2 PLLs which can be routed through dividers to 5 outputs.
+/* Each chip has different number of PLLs and outputs, for example:
+ * The CECE925 has 2 PLLs which can be routed through dividers to 5 outputs.
* Model this as 2 PLL clocks which are parents to the outputs.
*/
-#define NUMBER_OF_PLLS 2
-#define NUMBER_OF_OUTPUTS 5
+
+enum {
+ CDCE913,
+ CDCE925,
+ CDCE937,
+ CDCE949,
+};
+
+struct clk_cdce925_chip_info {
+ int num_plls;
+ int num_outputs;
+};
+
+static const struct clk_cdce925_chip_info clk_cdce925_chip_info_tbl[] = {
+ [CDCE913] = { .num_plls = 1, .num_outputs = 3 },
+ [CDCE925] = { .num_plls = 2, .num_outputs = 5 },
+ [CDCE937] = { .num_plls = 3, .num_outputs = 7 },
+ [CDCE949] = { .num_plls = 4, .num_outputs = 9 },
+};
+
+#define MAX_NUMBER_OF_PLLS 4
+#define MAX_NUMBER_OF_OUTPUTS 9
#define CDCE925_REG_GLOBAL1 0x01
#define CDCE925_REG_Y1SPIPDIVH 0x02
@@ -43,7 +64,7 @@ struct clk_cdce925_output {
struct clk_hw hw;
struct clk_cdce925_chip *chip;
u8 index;
- u16 pdiv; /* 1..127 for Y2-Y5; 1..1023 for Y1 */
+ u16 pdiv; /* 1..127 for Y2-Y9; 1..1023 for Y1 */
};
#define to_clk_cdce925_output(_hw) \
container_of(_hw, struct clk_cdce925_output, hw)
@@ -60,8 +81,9 @@ struct clk_cdce925_pll {
struct clk_cdce925_chip {
struct regmap *regmap;
struct i2c_client *i2c_client;
- struct clk_cdce925_pll pll[NUMBER_OF_PLLS];
- struct clk_cdce925_output clk[NUMBER_OF_OUTPUTS];
+ const struct clk_cdce925_chip_info *chip_info;
+ struct clk_cdce925_pll pll[MAX_NUMBER_OF_PLLS];
+ struct clk_cdce925_output clk[MAX_NUMBER_OF_OUTPUTS];
};
/* ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** */
@@ -284,6 +306,18 @@ static void cdce925_clk_set_pdiv(struct clk_cdce925_output *data, u16 pdiv)
case 4:
regmap_update_bits(data->chip->regmap, 0x27, 0x7F, pdiv);
break;
+ case 5:
+ regmap_update_bits(data->chip->regmap, 0x36, 0x7F, pdiv);
+ break;
+ case 6:
+ regmap_update_bits(data->chip->regmap, 0x37, 0x7F, pdiv);
+ break;
+ case 7:
+ regmap_update_bits(data->chip->regmap, 0x46, 0x7F, pdiv);
+ break;
+ case 8:
+ regmap_update_bits(data->chip->regmap, 0x47, 0x7F, pdiv);
+ break;
}
}
@@ -302,6 +336,14 @@ static void cdce925_clk_activate(struct clk_cdce925_output *data)
case 4:
regmap_update_bits(data->chip->regmap, 0x24, 0x03, 0x03);
break;
+ case 5:
+ case 6:
+ regmap_update_bits(data->chip->regmap, 0x34, 0x03, 0x03);
+ break;
+ case 7:
+ case 8:
+ regmap_update_bits(data->chip->regmap, 0x44, 0x03, 0x03);
+ break;
}
}
@@ -474,15 +516,6 @@ static const struct clk_ops cdce925_clk_y1_ops = {
.set_rate = cdce925_clk_y1_set_rate,
};
-
-static struct regmap_config cdce925_regmap_config = {
- .name = "configuration0",
- .reg_bits = 8,
- .val_bits = 8,
- .cache_type = REGCACHE_RBTREE,
- .max_register = 0x2F,
-};
-
#define CDCE925_I2C_COMMAND_BLOCK_TRANSFER 0x00
#define CDCE925_I2C_COMMAND_BYTE_TRANSFER 0x80
@@ -582,13 +615,19 @@ static int cdce925_probe(struct i2c_client *client,
struct clk_cdce925_chip *data;
struct device_node *node = client->dev.of_node;
const char *parent_name;
- const char *pll_clk_name[NUMBER_OF_PLLS] = {NULL,};
+ const char *pll_clk_name[MAX_NUMBER_OF_PLLS] = {NULL,};
struct clk_init_data init;
u32 value;
int i;
int err;
struct device_node *np_output;
char child_name[6];
+ struct regmap_config cdce925_regmap_config = {
+ .name = "configuration0",
+ .reg_bits = 8,
+ .val_bits = 8,
+ .cache_type = REGCACHE_RBTREE,
+ };
dev_dbg(&client->dev, "%s\n", __func__);
data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
@@ -596,6 +635,9 @@ static int cdce925_probe(struct i2c_client *client,
return -ENOMEM;
data->i2c_client = client;
+ data->chip_info = &clk_cdce925_chip_info_tbl[id->driver_data];
+ cdce925_regmap_config.max_register = CDCE925_OFFSET_PLL +
+ data->chip_info->num_plls * 0x10 - 1;
data->regmap = devm_regmap_init(&client->dev, ®map_cdce925_bus,
&client->dev, &cdce925_regmap_config);
if (IS_ERR(data->regmap)) {
@@ -626,7 +668,7 @@ static int cdce925_probe(struct i2c_client *client,
init.num_parents = parent_name ? 1 : 0;
/* Register PLL clocks */
- for (i = 0; i < NUMBER_OF_PLLS; ++i) {
+ for (i = 0; i < data->chip_info->num_plls; ++i) {
pll_clk_name[i] = kasprintf(GFP_KERNEL, "%s.pll%d",
client->dev.of_node->name, i);
init.name = pll_clk_name[i];
@@ -684,7 +726,7 @@ static int cdce925_probe(struct i2c_client *client,
init.ops = &cdce925_clk_ops;
init.flags = CLK_SET_RATE_PARENT;
init.num_parents = 1;
- for (i = 1; i < NUMBER_OF_OUTPUTS; ++i) {
+ for (i = 1; i < data->chip_info->num_outputs; ++i) {
init.name = kasprintf(GFP_KERNEL, "%s.Y%d",
client->dev.of_node->name, i+1);
data->clk[i].chip = data;
@@ -702,6 +744,16 @@ static int cdce925_probe(struct i2c_client *client,
/* Mux Y4/5 to PLL2 */
init.parent_names = &pll_clk_name[1];
break;
+ case 5:
+ case 6:
+ /* Mux Y6/7 to PLL3 */
+ init.parent_names = &pll_clk_name[2];
+ break;
+ case 7:
+ case 8:
+ /* Mux Y8/9 to PLL4 */
+ init.parent_names = &pll_clk_name[3];
+ break;
}
err = devm_clk_hw_register(&client->dev, &data->clk[i].hw);
kfree(init.name); /* clock framework made a copy of the name */
@@ -720,7 +772,7 @@ static int cdce925_probe(struct i2c_client *client,
err = 0;
error:
- for (i = 0; i < NUMBER_OF_PLLS; ++i)
+ for (i = 0; i < data->chip_info->num_plls; ++i)
/* clock framework made a copy of the name */
kfree(pll_clk_name[i]);
@@ -728,13 +780,19 @@ static int cdce925_probe(struct i2c_client *client,
}
static const struct i2c_device_id cdce925_id[] = {
- { "cdce925", 0 },
+ { "cdce913", CDCE913 },
+ { "cdce925", CDCE925 },
+ { "cdce937", CDCE937 },
+ { "cdce949", CDCE949 },
{ }
};
MODULE_DEVICE_TABLE(i2c, cdce925_id);
static const struct of_device_id clk_cdce925_of_match[] = {
+ { .compatible = "ti,cdce913" },
{ .compatible = "ti,cdce925" },
+ { .compatible = "ti,cdce937" },
+ { .compatible = "ti,cdce949" },
{ },
};
MODULE_DEVICE_TABLE(of, clk_cdce925_of_match);
@@ -750,5 +808,5 @@ static struct i2c_driver cdce925_driver = {
module_i2c_driver(cdce925_driver);
MODULE_AUTHOR("Mike Looijmans <mike.looijmans@xxxxxxxx>");
-MODULE_DESCRIPTION("cdce925 driver");
+MODULE_DESCRIPTION("TI CDCE913/925/937/949 driver");
MODULE_LICENSE("GPL");
