Re: [PATCH/RFT v2 12/17] USB: ochi-da8xx: Use a regulator for vbus/overcurrent

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Tue, Oct 25, 2016 at 3:39 AM, David Lechner <david@xxxxxxxxxxxxxx> wrote:
> On 10/24/2016 11:46 AM, ahaslam@xxxxxxxxxxxx wrote:
>>
>> From: Axel Haslam <ahaslam@xxxxxxxxxxxx>
>>
>> Currently, the da8xx ohci driver uses a set of gpios and callbacks in
>> board files to handle vbus and overcurrent irqs form the power supply.
>> However, this does not play nice when moving to a DT based boot were
>> we wont have board files.
>>
>> Instead of requesting and handling the gpio, use the regulator framework
>> to take care of enabling and disabling vbus power.
>> This has the benefit
>> that we dont need to pass any more platform data to the driver:
>>
>> These will be handled by the regulator framework:
>> set_power   ->  regulator_enable/regulator_disable
>> get_power   ->  regulator_is_enabled
>> get_oci     ->  regulator_get_mode
>> ocic_notify ->  regulator notification
>>
>> We can keep the default potpgt and use the regulator start delay instead:
>> potpgt      -> regulator startup delay time
>>
>> The hawk board does not have a GPIO/OVERCURRENT gpio to control vbus,
>> (they should not have been decleared/reserved) so, just remove those
>> definitions from the hwk board file.
>>
>> Signed-off-by: Axel Haslam <ahaslam@xxxxxxxxxxxx>
>> ---
>
>
>
> How do you recover after an overcurrent event?
>
> I have configured a fixed-regulator using device-tree, but similar to the
> configuration in the board files here. However, when I shorted out the VBUS
> and caused an overcurrent event, I see nothing in the kernel log saying that
> there was an overcurrent event and after I remove the short, the regulator
> is never turned back on.
>
>

You should have the patch to fix gpiolib, and you should declare the
over current gpio on the regulator as such:
(if the pin is enabled high you should add oc-active-high);

       vbus_fixed: fixed-regulator-vbus {
               compatible = "regulator-fixed";
               gpio = <&gpio 109 0>;
               oc-gpio = <&gpio 36 0>;
               regulator-boot-on;
               enable-active-high;
               regulator-name = "vbus";
               regulator-min-microvolt = <5000000>;
               regulator-max-microvolt = <5000000>;
       };


Question: Do you see that the over current gpio was requested
in debugfs/gpio? and, do you see the interrupt in /proc/interrupts?

If you unplug and plug in back the usb device it should work again.
also you can unbind and bind it should also start to work:
something like:

echo usb1 >/sys/bus/usb/drivers/usb/unbind
echo usb1 >/sys/bus/usb/drivers/usb/bind


>
>> @@ -163,7 +198,6 @@ static int ohci_da8xx_hub_control(struct usb_hcd *hcd,
>> u16 typeReq, u16 wValue,
>>                                   u16 wIndex, char *buf, u16 wLength)
>>  {
>>         struct device *dev              = hcd->self.controller;
>> -       struct da8xx_ohci_root_hub *hub = dev_get_platdata(dev);
>
>
> nit: unnecessary whitespace change
>
>>         int temp;
>>
>>         switch (typeReq) {
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux