Hello,
On Tuesday 18 Oct 2016 16:29:24 Geert Uytterhoeven wrote:
> On Wed, Oct 12, 2016 at 4:10 PM, Ramesh Shanmugasundaram wrote:
> > This patch adds Digital Radio Interface (DRIF) support to R-Car Gen3 SoCs.
> > The driver exposes each instance of DRIF as a V4L2 SDR device. A DRIF
> > device represents a channel and each channel can have one or two
> > sub-channels respectively depending on the target board.
> >
> > DRIF supports only Rx functionality. It receives samples from a RF
> > frontend tuner chip it is interfaced with. The combination of DRIF and the
> > tuner device, which is registered as a sub-device, determines the receive
> > sample rate and format.
> >
> > In order to be compliant as a V4L2 SDR device, DRIF needs to bind with
> > the tuner device, which can be provided by a third party vendor. DRIF acts
> > as a slave device and the tuner device acts as a master transmitting the
> > samples. The driver allows asynchronous binding of a tuner device that
> > is registered as a v4l2 sub-device. The driver can learn about the tuner
> > it is interfaced with based on port endpoint properties of the device in
> > device tree. The V4L2 SDR device inherits the controls exposed by the
> > tuner device.
> >
> > The device can also be configured to use either one or both of the data
> > pins at runtime based on the master (tuner) configuration.
>
> Thanks for your patch!
>
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt
> > @@ -0,0 +1,109 @@
> > +Renesas R-Car Gen3 DRIF controller (DRIF)
> > +-----------------------------------------
> > +
> > +Required properties:
> > +--------------------
> > +- compatible: "renesas,drif-r8a7795" if DRIF controller is a part of
> > R8A7795 SoC.
>
> "renesas,r8a7795-drif", as Rob already pointed out.
>
> > + "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible
> > device.
> > + When compatible with the generic version, nodes must list
> > the
> > + SoC-specific version corresponding to the platform first
> > + followed by the generic version.
> > +
> > +- reg: offset and length of each sub-channel.
> > +- interrupts: associated with each sub-channel.
> > +- clocks: phandles and clock specifiers for each sub-channel.
> > +- clock-names: clock input name strings: "fck0", "fck1".
> > +- pinctrl-0: pin control group to be used for this controller.
> > +- pinctrl-names: must be "default".
> > +- dmas: phandles to the DMA channels for each sub-channel.
> > +- dma-names: names for the DMA channels: "rx0", "rx1".
> > +
> > +Required child nodes:
> > +---------------------
> > +- Each DRIF channel can have one or both of the sub-channels enabled in a
> > + setup. The sub-channels are represented as a child node. The name of
> > the
> > + child nodes are "sub-channel0" and "sub-channel1" respectively. Each
> > child
> > + node supports the "status" property only, which is used to
> > enable/disable
> > + the respective sub-channel.
> >
> > +Example
> > +--------
> > +
> > +SoC common dtsi file
> > +
> > +drif0: rif@e6f40000 {
> > + compatible = "renesas,drif-r8a7795",
> > + "renesas,rcar-gen3-drif";
> > + reg = <0 0xe6f40000 0 0x64>, <0 0xe6f50000 0 0x64>;
> > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&cpg CPG_MOD 515>, <&cpg CPG_MOD 514>;
> > + clock-names = "fck0", "fck1";
> > + dmas = <&dmac1 0x20>, <&dmac1 0x22>;
> > + dma-names = "rx0", "rx1";
>
> I could not find the DMAC channels in the datasheet?
> Most modules are either tied to dmac0, or two both dmac1 and dmac2.
> In the latter case, you want to list two sets of dmas, one for each DMAC.
>
> > + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> > + status = "disabled";
> > +
> > + sub-channel0 {
> > + status = "disabled";
> > + };
> > +
> > + sub-channel1 {
> > + status = "disabled";
> > + };
> > +
> > +};
>
> As you're modelling this in DT under a single device node, this means you
> cannot use runtime PM to manage the module clocks of the individual
> channels.
>
> An alternative could be to have two separate nodes for each channel,
> and tie them together using a phandle.
A quick glance at the documentation shows no dependency between the two
channels at a software level. They both share the same clock and
synchronization input pins, but from a hardware point of view that seems to be
it. It thus looks like we could indeed model the two channels as separate
nodes, without tying them together.
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
