Pinmuxing for DRA7x/AM57x family of processors need to be done in IO isolation as part of initial bootloader executed from SRAM. This is done as part of iodelay configuration sequence and is required due to the limitations introduced by erratum ID: i869[1] (IO Glitches can occur when changing IO settings) and elaborated in the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements. Only peripheral that is permitted for dynamic pin mux configuration is MMC and DCAN. MMC is permitted to change to accommodate the requirements for varied speeds (which require IO-delay support in kernel as well). DCAN is a result of i893[1] (DCAN initialization sequence). With the exception of DCAN and MMC, all other pin mux configurations are removed from the dts. [1] http://www.ti.com/lit/er/sprz436a/sprz436a.pdf [2] http://www.ti.com/lit/ug/spruhz7c/spruhz7c.pdf Signed-off-by: Lokesh Vutla <lokeshvutla@xxxxxx> --- arch/arm/boot/dts/dra72-evm-common.dtsi | 192 -------------------------------- 1 file changed, 192 deletions(-) diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi index c94d8d64..3c02612 100644 --- a/arch/arm/boot/dts/dra72-evm-common.dtsi +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi @@ -69,9 +69,6 @@ tpd12s015: encoder { compatible = "ti,tpd12s015"; - pinctrl-names = "default"; - pinctrl-0 = <&tpd12s015_pins>; - gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ @@ -134,72 +131,6 @@ }; &dra7_pmx_core { - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ - DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - nand_default: nand_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ - DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ - DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ - DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ - DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ - DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ - DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ - DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ - DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ - DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ - DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ - DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ - DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ - DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ - DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ - DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ - DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ - DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ - DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ - DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ - DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ - DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ - >; - }; - - usb1_pins: pinmux_usb1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ - >; - }; - - usb2_pins: pinmux_usb2_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ - >; - }; - - tps65917_pins_default: tps65917_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ - >; - }; - mmc1_pins_default: mmc1_pins_default { pinctrl-single,pins = < DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ @@ -240,59 +171,16 @@ DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ >; }; - - hdmi_pins: pinmux_hdmi_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ - DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ - >; - }; - - tpd12s015_pins: pinmux_tpd12s015_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ - >; - }; - - atl_pins: pinmux_atl_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ - DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ - >; - }; - - mcasp3_pins: pinmux_mcasp3_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ - DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ - DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ - >; - }; - - mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15) - >; - }; }; &i2c1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; clock-frequency = <400000>; tps65917: tps65917@58 { compatible = "ti,tps65917"; reg = <0x58>; - pinctrl-names = "default"; - pinctrl-0 = <&tps65917_pins_default>; - interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ interrupt-controller; #interrupt-cells = <2>; @@ -423,8 +311,6 @@ &i2c5 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c5_pins>; clock-frequency = <400000>; pcf_hdmi: pcf8575@26 { @@ -462,8 +348,6 @@ &gpmc { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&nand_default>; ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */ nand@0,0 { /* To use NAND, DIP switch SW5 must be set like so: @@ -566,14 +450,10 @@ &usb1 { dr_mode = "peripheral"; - pinctrl-names = "default"; - pinctrl-0 = <&usb1_pins>; }; &usb2 { dr_mode = "host"; - pinctrl-names = "default"; - pinctrl-0 = <&usb2_pins>; }; &mmc1 { @@ -603,71 +483,8 @@ max-frequency = <192000000>; }; -&dra7_pmx_core { - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ - DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ - DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ - DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ - DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ - DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ - DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ - DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ - DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ - DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ - DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ - >; - - }; - - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15) - >; - }; - - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ - DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; - - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15) - >; - }; -}; - &mac { status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&cpsw_default>; - pinctrl-1 = <&cpsw_sleep>; -}; - -&davinci_mdio { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&davinci_mdio_default>; - pinctrl-1 = <&davinci_mdio_sleep>; }; &dcan1 { @@ -748,9 +565,6 @@ &hdmi { status = "ok"; - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_pins>; - port { hdmi_out: endpoint { remote-endpoint = <&tpd12s015_in>; @@ -759,9 +573,6 @@ }; &atl { - pinctrl-names = "default"; - pinctrl-0 = <&atl_pins>; - assigned-clocks = <&abe_dpll_sys_clk_mux>, <&atl_gfclk_mux>, <&dpll_abe_ck>, @@ -780,9 +591,6 @@ &mcasp3 { #sound-dai-cells = <0>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mcasp3_pins>; - pinctrl-1 = <&mcasp3_sleep_pins>; assigned-clocks = <&mcasp3_ahclkx_mux>; assigned-clock-parents = <&atl_clkin2_ck>; -- 2.9.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
