From: Ziji Hu <huziji@xxxxxxxxxxx>
Add Xenon eMMC/SD/SDIO host controller core functionality.
Add Xenon specific intialization process.
Add Xenon specific mmc_host_ops APIs.
Add Xenon specific register definitions.
Add CONFIG_MMC_SDHCI_XENON support in drivers/mmc/host/Kconfig.
Marvell Xenon SDHC conforms to SD Physical Layer Specification
Version 3.01 and is designed according to the guidelines provided
in the SD Host Controller Standard Specification Version 3.00.
Signed-off-by: Hu Ziji <huziji@xxxxxxxxxxx>
Reviewed-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx>
---
MAINTAINERS | 1 +-
drivers/mmc/host/Kconfig | 9 +-
drivers/mmc/host/Makefile | 3 +-
drivers/mmc/host/sdhci-xenon.c | 599 ++++++++++++++++++++++++++++++++++-
drivers/mmc/host/sdhci-xenon.h | 134 ++++++++-
5 files changed, 746 insertions(+), 0 deletions(-)
create mode 100644 drivers/mmc/host/sdhci-xenon.c
create mode 100644 drivers/mmc/host/sdhci-xenon.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 4aa0eac9bfc7..859420e5dfd3 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7582,6 +7582,7 @@ MARVELL XENON MMC/SD/SDIO HOST CONTROLLER DRIVER
M: Ziji Hu <huziji@xxxxxxxxxxx>
L: linux-mmc@xxxxxxxxxxxxxxx
S: Supported
+F: drivers/mmc/host/sdhci-xenon.*
F: Documentation/devicetree/bindings/mmc/marvell,sdhci-xenon.txt
MATROX FRAMEBUFFER DRIVER
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 5274f503a39a..85a53623526a 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -798,3 +798,12 @@ config MMC_SDHCI_BRCMSTB
Broadcom STB SoCs.
If unsure, say Y.
+
+config MMC_SDHCI_XENON
+ tristate "Marvell Xenon eMMC/SD/SDIO SDHCI driver"
+ depends on MMC_SDHCI && MMC_SDHCI_PLTFM
+ help
+ This selects Marvell Xenon eMMC/SD/SDIO SDHCI.
+ If you have a machine with integrated Marvell Xenon SDHC IP,
+ say Y or M here.
+ If unsure, say N.
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index e2bdaaf43184..75eaf743486c 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -80,3 +80,6 @@ obj-$(CONFIG_MMC_SDHCI_BRCMSTB) += sdhci-brcmstb.o
ifeq ($(CONFIG_CB710_DEBUG),y)
CFLAGS-cb710-mmc += -DDEBUG
endif
+
+obj-$(CONFIG_MMC_SDHCI_XENON) += sdhci-xenon-driver.o
+sdhci-xenon-driver-y += sdhci-xenon.o
diff --git a/drivers/mmc/host/sdhci-xenon.c b/drivers/mmc/host/sdhci-xenon.c
new file mode 100644
index 000000000000..03ba183494d3
--- /dev/null
+++ b/drivers/mmc/host/sdhci-xenon.c
@@ -0,0 +1,599 @@
+/*
+ * Driver for Marvell SOC Platform Group Xenon SDHC as a platform device
+ *
+ * Copyright (C) 2016 Marvell, All Rights Reserved.
+ *
+ * Author: Hu Ziji <huziji@xxxxxxxxxxx>
+ * Date: 2016-8-24
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * Inspired by Jisheng Zhang <jszhang@xxxxxxxxxxx>
+ * Special thanks to Video BG4 project team.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/sdio.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+#include <linux/module.h>
+#include <linux/of.h>
+
+#include "sdhci-pltfm.h"
+#include "sdhci.h"
+#include "sdhci-xenon.h"
+
+/* Set SDCLK-off-while-idle */
+static void xenon_set_sdclk_off_idle(struct sdhci_host *host,
+ unsigned char slot_idx, bool enable)
+{
+ u32 reg;
+ u32 mask;
+
+ reg = sdhci_readl(host, SDHC_SYS_OP_CTRL);
+ /* Get the bit shift basing on the slot index */
+ mask = (0x1 << (SDCLK_IDLEOFF_ENABLE_SHIFT + slot_idx));
+ if (enable)
+ reg |= mask;
+ else
+ reg &= ~mask;
+
+ sdhci_writel(host, reg, SDHC_SYS_OP_CTRL);
+}
+
+/* Enable/Disable the Auto Clock Gating function */
+static void xenon_set_acg(struct sdhci_host *host, bool enable)
+{
+ u32 reg;
+
+ reg = sdhci_readl(host, SDHC_SYS_OP_CTRL);
+ if (enable)
+ reg &= ~AUTO_CLKGATE_DISABLE_MASK;
+ else
+ reg |= AUTO_CLKGATE_DISABLE_MASK;
+ sdhci_writel(host, reg, SDHC_SYS_OP_CTRL);
+}
+
+/* Enable this slot */
+static void xenon_enable_slot(struct sdhci_host *host,
+ unsigned char slot_idx)
+{
+ u32 reg;
+
+ reg = sdhci_readl(host, SDHC_SYS_OP_CTRL);
+ reg |= (BIT(slot_idx) << SLOT_ENABLE_SHIFT);
+ sdhci_writel(host, reg, SDHC_SYS_OP_CTRL);
+
+ /*
+ * Manually set the flag which all the slots require,
+ * including SD, eMMC, SDIO
+ */
+ host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
+}
+
+/* Disable this slot */
+static void xenon_disable_slot(struct sdhci_host *host,
+ unsigned char slot_idx)
+{
+ u32 reg;
+
+ reg = sdhci_readl(host, SDHC_SYS_OP_CTRL);
+ reg &= ~(BIT(slot_idx) << SLOT_ENABLE_SHIFT);
+ sdhci_writel(host, reg, SDHC_SYS_OP_CTRL);
+}
+
+/* Enable Parallel Transfer Mode */
+static void xenon_enable_slot_parallel_tran(struct sdhci_host *host,
+ unsigned char slot_idx)
+{
+ u32 reg;
+
+ reg = sdhci_readl(host, SDHC_SYS_EXT_OP_CTRL);
+ reg |= BIT(slot_idx);
+ sdhci_writel(host, reg, SDHC_SYS_EXT_OP_CTRL);
+}
+
+static void xenon_slot_tuning_setup(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+ u32 reg;
+
+ /* Disable the Re-Tuning Request functionality */
+ reg = sdhci_readl(host, SDHC_SLOT_RETUNING_REQ_CTRL);
+ reg &= ~RETUNING_COMPATIBLE;
+ sdhci_writel(host, reg, SDHC_SLOT_RETUNING_REQ_CTRL);
+
+ /* Disbale the Re-tuning Event Signal Enable */
+ reg = sdhci_readl(host, SDHCI_SIGNAL_ENABLE);
+ reg &= ~SDHCI_INT_RETUNE;
+ sdhci_writel(host, reg, SDHCI_SIGNAL_ENABLE);
+
+ /* Force to use Tuning Mode 1 */
+ host->tuning_mode = SDHCI_TUNING_MODE_1;
+ /* Set re-tuning period */
+ host->tuning_count = 1 << (priv->tuning_count - 1);
+}
+
+/*
+ * Operations inside struct sdhci_ops
+ */
+/* Recover the Register Setting cleared during SOFTWARE_RESET_ALL */
+static void sdhci_xenon_reset_exit(struct sdhci_host *host,
+ unsigned char slot_idx, u8 mask)
+{
+ /* Only SOFTWARE RESET ALL will clear the register setting */
+ if (!(mask & SDHCI_RESET_ALL))
+ return;
+
+ /* Disable tuning request and auto-retuing again */
+ xenon_slot_tuning_setup(host);
+
+ xenon_set_acg(host, true);
+
+ xenon_set_sdclk_off_idle(host, slot_idx, false);
+}
+
+static void sdhci_xenon_reset(struct sdhci_host *host, u8 mask)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+
+ sdhci_reset(host, mask);
+ sdhci_xenon_reset_exit(host, priv->slot_idx, mask);
+}
+
+/*
+ * Xenon defines different values for HS200 and SDR104
+ * in Host_Control_2
+ */
+static void xenon_set_uhs_signaling(struct sdhci_host *host,
+ unsigned int timing)
+{
+ u16 ctrl_2;
+
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ /* Select Bus Speed Mode for host */
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ if (timing == MMC_TIMING_MMC_HS200)
+ ctrl_2 |= XENON_SDHCI_CTRL_HS200;
+ else if (timing == MMC_TIMING_UHS_SDR104)
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
+ else if (timing == MMC_TIMING_UHS_SDR12)
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
+ else if (timing == MMC_TIMING_UHS_SDR25)
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
+ else if (timing == MMC_TIMING_UHS_SDR50)
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
+ else if ((timing == MMC_TIMING_UHS_DDR50) ||
+ (timing == MMC_TIMING_MMC_DDR52))
+ ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
+ else if (timing == MMC_TIMING_MMC_HS400)
+ ctrl_2 |= XENON_SDHCI_CTRL_HS400;
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+}
+
+static const struct sdhci_ops sdhci_xenon_ops = {
+ .set_clock = sdhci_set_clock,
+ .set_bus_width = sdhci_set_bus_width,
+ .reset = sdhci_xenon_reset,
+ .set_uhs_signaling = xenon_set_uhs_signaling,
+ .get_max_clock = sdhci_pltfm_clk_get_max_clock,
+};
+
+static const struct sdhci_pltfm_data sdhci_xenon_pdata = {
+ .ops = &sdhci_xenon_ops,
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+ SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 |
+ SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+};
+
+/*
+ * Xenon Specific Operations in mmc_host_ops
+ */
+static void xenon_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+ unsigned long flags;
+
+ /*
+ * HS400/HS200/eMMC HS doesn't have Preset Value register.
+ * However, sdhci_set_ios will read HS400/HS200 Preset register.
+ * Disable Preset Value register for HS400/HS200.
+ * eMMC HS with preset_enabled set will trigger a bug in
+ * get_preset_value().
+ */
+ spin_lock_irqsave(&host->lock, flags);
+ if ((ios->timing == MMC_TIMING_MMC_HS400) ||
+ (ios->timing == MMC_TIMING_MMC_HS200) ||
+ (ios->timing == MMC_TIMING_MMC_HS)) {
+ host->preset_enabled = false;
+ host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
+ } else {
+ host->quirks2 &= ~SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
+ }
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ sdhci_set_ios(mmc, ios);
+
+ if (host->clock > DEFAULT_SDCLK_FREQ) {
+ spin_lock_irqsave(&host->lock, flags);
+ xenon_set_sdclk_off_idle(host, priv->slot_idx, true);
+ spin_unlock_irqrestore(&host->lock, flags);
+ }
+}
+
+static int __emmc_signal_voltage_switch(struct mmc_host *mmc,
+ const unsigned char signal_voltage)
+{
+ u32 ctrl;
+ unsigned char voltage_code;
+ struct sdhci_host *host = mmc_priv(mmc);
+
+ if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
+ voltage_code = EMMC_VCCQ_3_3V;
+ else if (signal_voltage == MMC_SIGNAL_VOLTAGE_180)
+ voltage_code = EMMC_VCCQ_1_8V;
+ else
+ return -EINVAL;
+
+ /*
+ * This host is for eMMC, XENON self-defined
+ * eMMC slot control register should be accessed
+ * instead of Host Control 2
+ */
+ ctrl = sdhci_readl(host, SDHC_SLOT_EMMC_CTRL);
+ ctrl &= ~EMMC_VCCQ_MASK;
+ ctrl |= voltage_code;
+ sdhci_writel(host, ctrl, SDHC_SLOT_EMMC_CTRL);
+
+ /* There is no standard to determine this waiting period */
+ usleep_range(1000, 2000);
+
+ /* Check whether io voltage switch is done */
+ ctrl = sdhci_readl(host, SDHC_SLOT_EMMC_CTRL);
+ ctrl &= EMMC_VCCQ_MASK;
+ /*
+ * This bit is set only when regulator feeds back the voltage switch
+ * results to Xenon SDHC.
+ * However, in actaul implementation, regulator might not provide
+ * this feedback.
+ * Thus we shall not rely on this bit to determine if switch failed.
+ * If the bit is not set, just throw a message.
+ * Besides, error code should not be returned.
+ */
+ if (ctrl != voltage_code)
+ dev_info(mmc_dev(mmc), "fail to detect eMMC signal voltage stable\n");
+ return 0;
+}
+
+static int xenon_emmc_signal_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ unsigned char voltage = ios->signal_voltage;
+
+ if ((voltage == MMC_SIGNAL_VOLTAGE_330) ||
+ (voltage == MMC_SIGNAL_VOLTAGE_180))
+ return __emmc_signal_voltage_switch(mmc, voltage);
+
+ dev_err(mmc_dev(mmc), "Unsupported signal voltage: %d\n",
+ voltage);
+ return -EINVAL;
+}
+
+static int xenon_start_signal_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+
+ /*
+ * Before SD/SDIO set signal voltage, SD bus clock should be
+ * disabled. However, sdhci_set_clock will also disable the Internal
+ * clock in mmc_set_signal_voltage().
+ * If Internal clock is disabled, the 3.3V/1.8V bit can not be updated.
+ * Thus here manually enable internal clock.
+ *
+ * After switch completes, it is unnecessary to disable internal clock,
+ * since keeping internal clock active obeys SD spec.
+ */
+ enable_xenon_internal_clk(host);
+
+ if (priv->card_candidate) {
+ if (mmc_card_mmc(priv->card_candidate))
+ return xenon_emmc_signal_voltage_switch(mmc, ios);
+ }
+
+ return sdhci_start_signal_voltage_switch(mmc, ios);
+}
+
+/*
+ * After determining which slot is used for SDIO,
+ * some additional task is required.
+ */
+static void xenon_init_card(struct mmc_host *mmc, struct mmc_card *card)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ u32 reg;
+ u8 slot_idx;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+
+ /* Link the card for delay adjustment */
+ priv->card_candidate = card;
+ /* Set tuning functionality of this slot */
+ xenon_slot_tuning_setup(host);
+
+ slot_idx = priv->slot_idx;
+ if (!mmc_card_sdio(card)) {
+ /* Re-enable the Auto-CMD12 cap flag. */
+ host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
+ host->flags |= SDHCI_AUTO_CMD12;
+
+ /* Clear SDIO Card Inserted indication */
+ reg = sdhci_readl(host, SDHC_SYS_CFG_INFO);
+ reg &= ~(1 << (slot_idx + SLOT_TYPE_SDIO_SHIFT));
+ sdhci_writel(host, reg, SDHC_SYS_CFG_INFO);
+
+ if (mmc_card_mmc(card)) {
+ mmc->caps |= MMC_CAP_NONREMOVABLE;
+ if (!(host->quirks2 & SDHCI_QUIRK2_NO_1_8_V))
+ mmc->caps |= MMC_CAP_1_8V_DDR;
+ /*
+ * Force to clear BUS_TEST to
+ * skip bus_test_pre and bus_test_post
+ */
+ mmc->caps &= ~MMC_CAP_BUS_WIDTH_TEST;
+ mmc->caps2 |= MMC_CAP2_HC_ERASE_SZ |
+ MMC_CAP2_PACKED_CMD;
+ if (mmc->caps & MMC_CAP_8_BIT_DATA)
+ mmc->caps2 |= MMC_CAP2_HS400_1_8V;
+ }
+ } else {
+ /*
+ * Delete the Auto-CMD12 cap flag.
+ * Otherwise, when sending multi-block CMD53,
+ * Driver will set Transfer Mode Register to enable Auto CMD12.
+ * However, SDIO device cannot recognize CMD12.
+ * Thus SDHC will time-out for waiting for CMD12 response.
+ */
+ host->quirks &= ~SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
+ host->flags &= ~SDHCI_AUTO_CMD12;
+
+ /*
+ * Set SDIO Card Inserted indication
+ * to inform that the current slot is for SDIO
+ */
+ reg = sdhci_readl(host, SDHC_SYS_CFG_INFO);
+ reg |= (1 << (slot_idx + SLOT_TYPE_SDIO_SHIFT));
+ sdhci_writel(host, reg, SDHC_SYS_CFG_INFO);
+ }
+}
+
+static int xenon_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+
+ if (host->timing == MMC_TIMING_UHS_DDR50)
+ return 0;
+
+ return sdhci_execute_tuning(mmc, opcode);
+}
+
+static void xenon_replace_mmc_host_ops(struct sdhci_host *host)
+{
+ host->mmc_host_ops.set_ios = xenon_set_ios;
+ host->mmc_host_ops.start_signal_voltage_switch =
+ xenon_start_signal_voltage_switch;
+ host->mmc_host_ops.init_card = xenon_init_card;
+ host->mmc_host_ops.execute_tuning = xenon_execute_tuning;
+}
+
+static int xenon_probe_dt(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+ int err;
+ u32 slot_idx, nr_slot;
+ u32 tuning_count;
+ u32 reg;
+
+ /* Standard MMC property */
+ err = mmc_of_parse(mmc);
+ if (err)
+ return err;
+
+ /* Standard SDHCI property */
+ sdhci_get_of_property(pdev);
+
+ /*
+ * Xenon Specific property:
+ * slotno: the index of slot. Refer to SDHC_SYS_CFG_INFO register
+ * tuning-count: the interval between re-tuning
+ * PHY type: "sdhc phy", "emmc phy 5.0" or "emmc phy 5.1"
+ */
+ if (!of_property_read_u32(np, "xenon,slotno", &slot_idx)) {
+ nr_slot = sdhci_readl(host, SDHC_SYS_CFG_INFO);
+ nr_slot &= NR_SUPPORTED_SLOT_MASK;
+ if (unlikely(slot_idx > nr_slot)) {
+ dev_err(mmc_dev(mmc), "Slot Index %d exceeds Number of slots %d\n",
+ slot_idx, nr_slot);
+ return -EINVAL;
+ }
+ } else {
+ priv->slot_idx = 0x0;
+ }
+
+ if (!of_property_read_u32(np, "xenon,tuning-count", &tuning_count)) {
+ if (unlikely(tuning_count >= TMR_RETUN_NO_PRESENT)) {
+ dev_err(mmc_dev(mmc), "Wrong Re-tuning Count. Set default value %d\n",
+ DEF_TUNING_COUNT);
+ tuning_count = DEF_TUNING_COUNT;
+ }
+ } else {
+ priv->tuning_count = DEF_TUNING_COUNT;
+ }
+
+ if (of_property_read_bool(np, "xenon,mask-conflict-err")) {
+ reg = sdhci_readl(host, SDHC_SYS_EXT_OP_CTRL);
+ reg |= MASK_CMD_CONFLICT_ERROR;
+ sdhci_writel(host, reg, SDHC_SYS_EXT_OP_CTRL);
+ }
+
+ return err;
+}
+
+static int xenon_slot_probe(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+ u8 slot_idx = priv->slot_idx;
+
+ /* Enable slot */
+ xenon_enable_slot(host, slot_idx);
+
+ /* Enable ACG */
+ xenon_set_acg(host, true);
+
+ /* Enable Parallel Transfer Mode */
+ xenon_enable_slot_parallel_tran(host, slot_idx);
+
+ priv->timing = MMC_TIMING_FAKE;
+ priv->clock = 0;
+
+ return 0;
+}
+
+static void xenon_slot_remove(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+ u8 slot_idx = priv->slot_idx;
+
+ /* disable slot */
+ xenon_disable_slot(host, slot_idx);
+}
+
+static int sdhci_xenon_probe(struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_host *host;
+ struct clk *clk, *axi_clk;
+ struct sdhci_xenon_priv *priv;
+ int err;
+
+ host = sdhci_pltfm_init(pdev, &sdhci_xenon_pdata,
+ sizeof(struct sdhci_xenon_priv));
+ if (IS_ERR(host))
+ return PTR_ERR(host);
+
+ pltfm_host = sdhci_priv(host);
+ priv = sdhci_pltfm_priv(pltfm_host);
+
+ xenon_set_acg(host, false);
+
+ /*
+ * Link Xenon specific mmc_host_ops function,
+ * to replace standard ones in sdhci_ops.
+ */
+ xenon_replace_mmc_host_ops(host);
+
+ clk = devm_clk_get(&pdev->dev, "core");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "Failed to setup input clk.\n");
+ err = PTR_ERR(clk);
+ goto free_pltfm;
+ }
+ clk_prepare_enable(clk);
+ pltfm_host->clk = clk;
+
+ /*
+ * Some SOCs require additional clock to
+ * manage AXI bus clock.
+ * It is optional.
+ */
+ axi_clk = devm_clk_get(&pdev->dev, "axi");
+ if (!IS_ERR(axi_clk)) {
+ clk_prepare_enable(axi_clk);
+ priv->axi_clk = axi_clk;
+ }
+
+ err = xenon_probe_dt(pdev);
+ if (err)
+ goto err_clk;
+
+ err = xenon_slot_probe(host);
+ if (err)
+ goto err_clk;
+
+ err = sdhci_add_host(host);
+ if (err)
+ goto remove_slot;
+
+ return 0;
+
+remove_slot:
+ xenon_slot_remove(host);
+err_clk:
+ clk_disable_unprepare(pltfm_host->clk);
+ if (!IS_ERR(axi_clk))
+ clk_disable_unprepare(axi_clk);
+free_pltfm:
+ sdhci_pltfm_free(pdev);
+ return err;
+}
+
+static int sdhci_xenon_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_xenon_priv *priv = sdhci_pltfm_priv(pltfm_host);
+ int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xFFFFFFFF);
+
+ xenon_slot_remove(host);
+
+ sdhci_remove_host(host, dead);
+
+ clk_disable_unprepare(pltfm_host->clk);
+ clk_disable_unprepare(priv->axi_clk);
+
+ sdhci_pltfm_free(pdev);
+
+ return 0;
+}
+
+static const struct of_device_id sdhci_xenon_dt_ids[] = {
+ { .compatible = "marvell,sdhci-xenon",},
+ { .compatible = "marvell,armada-3700-sdhci",},
+ {}
+};
+MODULE_DEVICE_TABLE(of, sdhci_xenon_dt_ids);
+
+static struct platform_driver sdhci_xenon_driver = {
+ .driver = {
+ .name = "sdhci-xenon",
+ .of_match_table = sdhci_xenon_dt_ids,
+ .pm = &sdhci_pltfm_pmops,
+ },
+ .probe = sdhci_xenon_probe,
+ .remove = sdhci_xenon_remove,
+};
+
+module_platform_driver(sdhci_xenon_driver);
+
+MODULE_DESCRIPTION("SDHCI platform driver for Marvell Xenon SDHC");
+MODULE_AUTHOR("Hu Ziji <huziji@xxxxxxxxxxx>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mmc/host/sdhci-xenon.h b/drivers/mmc/host/sdhci-xenon.h
new file mode 100644
index 000000000000..c2370493fbe8
--- /dev/null
+++ b/drivers/mmc/host/sdhci-xenon.h
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) 2016 Marvell, All Rights Reserved.
+ *
+ * Author: Hu Ziji <huziji@xxxxxxxxxxx>
+ * Date: 2016-8-24
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ */
+#ifndef SDHCI_XENON_H_
+#define SDHCI_XENON_H_
+
+#include <linux/clk.h>
+#include <linux/mmc/card.h>
+#include <linux/of.h>
+#include "sdhci.h"
+
+/* Register Offset of SD Host Controller SOCP self-defined register */
+#define SDHC_SYS_CFG_INFO 0x0104
+#define SLOT_TYPE_SDIO_SHIFT 24
+#define SLOT_TYPE_EMMC_MASK 0xFF
+#define SLOT_TYPE_EMMC_SHIFT 16
+#define SLOT_TYPE_SD_SDIO_MMC_MASK 0xFF
+#define SLOT_TYPE_SD_SDIO_MMC_SHIFT 8
+#define NR_SUPPORTED_SLOT_MASK 0x7
+
+#define SDHC_SYS_OP_CTRL 0x0108
+#define AUTO_CLKGATE_DISABLE_MASK BIT(20)
+#define SDCLK_IDLEOFF_ENABLE_SHIFT 8
+#define SLOT_ENABLE_SHIFT 0
+
+#define SDHC_SYS_EXT_OP_CTRL 0x010C
+#define MASK_CMD_CONFLICT_ERROR BIT(8)
+
+#define SDHC_SLOT_OP_STATUS_CTRL 0x0128
+#define DELAY_90_DEGREE_MASK_EMMC5 BIT(7)
+#define DELAY_90_DEGREE_SHIFT_EMMC5 7
+#define EMMC_5_0_PHY_FIXED_DELAY_MASK 0x7F
+#define EMMC_PHY_FIXED_DELAY_MASK 0xFF
+#define EMMC_PHY_FIXED_DELAY_WINDOW_MIN (EMMC_PHY_FIXED_DELAY_MASK >> 3)
+#define SDH_PHY_FIXED_DELAY_MASK 0x1FF
+#define SDH_PHY_FIXED_DELAY_WINDOW_MIN (SDH_PHY_FIXED_DELAY_MASK >> 4)
+
+#define TUN_CONSECUTIVE_TIMES_SHIFT 16
+#define TUN_CONSECUTIVE_TIMES_MASK 0x7
+#define TUN_CONSECUTIVE_TIMES 0x4
+#define TUNING_STEP_SHIFT 12
+#define TUNING_STEP_MASK 0xF
+#define TUNING_STEP_DIVIDER BIT(6)
+
+#define FORCE_SEL_INVERSE_CLK_SHIFT 11
+
+#define SDHC_SLOT_EMMC_CTRL 0x0130
+#define ENABLE_DATA_STROBE BIT(24)
+#define SET_EMMC_RSTN BIT(16)
+#define DISABLE_RD_DATA_CRC BIT(14)
+#define DISABLE_CRC_STAT_TOKEN BIT(13)
+#define EMMC_VCCQ_MASK 0x3
+#define EMMC_VCCQ_1_8V 0x1
+#define EMMC_VCCQ_3_3V 0x3
+
+#define SDHC_SLOT_RETUNING_REQ_CTRL 0x0144
+/* retuning compatible */
+#define RETUNING_COMPATIBLE 0x1
+
+#define SDHC_SLOT_EXT_PRESENT_STATE 0x014C
+#define LOCK_STATE 0x1
+
+#define SDHC_SLOT_DLL_CUR_DLY_VAL 0x0150
+
+/* Tuning Parameter */
+#define TMR_RETUN_NO_PRESENT 0xF
+#define DEF_TUNING_COUNT 0x9
+
+#define MMC_TIMING_FAKE 0xFF
+
+#define DEFAULT_SDCLK_FREQ (400000)
+
+/* Xenon specific Mode Select value */
+#define XENON_SDHCI_CTRL_HS200 0x5
+#define XENON_SDHCI_CTRL_HS400 0x6
+
+struct sdhci_xenon_priv {
+ /*
+ * The bus_width, timing, and clock fields in below
+ * record the current setting of Xenon SDHC.
+ * Driver will call a Sampling Fixed Delay Adjustment
+ * if any setting is changed.
+ */
+ unsigned char bus_width;
+ unsigned char timing;
+ unsigned char tuning_count;
+ unsigned int clock;
+ struct clk *axi_clk;
+
+ /* Slot idx */
+ u8 slot_idx;
+
+ /*
+ * When initializing card, Xenon has to determine card type and
+ * adjust Sampling Fixed delay.
+ * However, at that time, card structure is not linked to mmc_host.
+ * Thus a card pointer is added here to provide
+ * the delay adjustment function with the card structure
+ * of the card during initialization
+ */
+ struct mmc_card *card_candidate;
+};
+
+static inline int enable_xenon_internal_clk(struct sdhci_host *host)
+{
+ u32 reg;
+ u8 timeout;
+
+ reg = sdhci_readl(host, SDHCI_CLOCK_CONTROL);
+ reg |= SDHCI_CLOCK_INT_EN;
+ sdhci_writel(host, reg, SDHCI_CLOCK_CONTROL);
+ /* Wait max 20 ms */
+ timeout = 20;
+ while (!((reg = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
+ & SDHCI_CLOCK_INT_STABLE)) {
+ if (timeout == 0) {
+ pr_err("%s: Internal clock never stabilised.\n",
+ mmc_hostname(host->mmc));
+ return -ETIMEDOUT;
+ }
+ timeout--;
+ mdelay(1);
+ }
+
+ return 0;
+}
+#endif
--
git-series 0.8.10
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
