On Fri, Sep 16, 2016 at 04:48:41PM -0500, Paul.Handrigan@xxxxxxxxxx wrote:
> From: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
>
> Add device tree bindings file for the cs35l34 8V boosted
> class D amplifier.
>
> Signed-off-by: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
> ---
> .../devicetree/bindings/sound/cs35l34.txt | 64 ++++++++++++++++++++++
> 1 file changed, 64 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/sound/cs35l34.txt
>
> diff --git a/Documentation/devicetree/bindings/sound/cs35l34.txt b/Documentation/devicetree/bindings/sound/cs35l34.txt
> new file mode 100644
> index 0000000..df62e77
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/sound/cs35l34.txt
> @@ -0,0 +1,64 @@
> +CS35L34 Speaker Amplifier
> +
> +Required properties:
> +
> + - compatible : "cirrus,cs35l34"
> +
> + - reg : the I2C address of the device for I2C.
> +
> + - VA-supply, VP-supply : power supplies for the device,
> + as covered in
> + Documentation/devicetree/bindings/regulator/regulator.txt.
> +
> + - cirrus,boost-vtge : Boost Voltage Value. Configures the boost converter's
> + output voltage in mV. The range is from VP to 8V with increments of 100mV.
Needs a unit suffix and -microvolt is preferred.
> +
> + - cirrus,boost-ind: Inductor value for boost converter. The value is in nH
> + and they can be values of 1000nH, 1100nH, 1200nH, 1500nH, and 2200nH.
Please add this unit to property-units.txt and use the suffix here.
> +
> +Optional properties:
> +
> + - reset-gpios: GPIO used to reset the amplifier.
> +
> + - interrupt-parent : Specifies the phandle of the interrupt controller to
> + which the IRQs from CS35L34 are delivered to.
> + - interrupts : IRQ line info CS35L34.
> + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> + for further information relating to interrupt properties)
> +
> + - cirrus,boost-peak : Boost converter peak current limit in mA. The range
> + starts at 1200mA and goes to a maximum of 3840mA with increments of 80mA.
> + The default value is 2480mA.
unit suffix.
> +
> + - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the
> + received mono data is in the left or right portion of the I2S frame
> + according to the AD0 pin or directly via this configuration.
> + 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel),
> + 0x2 = Left,
> + 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right
> + channel),
> + 0x3 = Right.
> +
> + - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take
> + effect without waiting for a zero cross.
> +
> + - cirrus,tdm_rising_edge: Boolean property. If set, data is on the rising edge of
> + SCLK. Otherwise, data is on the falling edge of SCLK.
Use '-', not '_'.
> +
> +
> +Example:
> +
> +cs35l34: cs35l34@40 {
> + compatible = "cirrus,cs35l34";
> + reg = <0x40>;
> +
> + interrupt-parent = <&gpio8>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> + reset-gpios = <&gpio 10 0>;
> +
> + cirrus,boost-vtge = <8000>; /* 8V */
> + cirrus,boost-ind = <1000>; /* 1uH */
> + cirrus,boost-peak = <3000>; /* 3A */
> +};
> +
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
