On Tue, Sep 13, 2016 at 05:43:14PM -0700, Kevin Hilman wrote:
> Add binding and basic support for the SD/eMMC controller on Amlogic
> S905/GXBB devices.
>
> Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxxxx>
> ---
> .../devicetree/bindings/mmc/amlogic,meson-gxbb.txt | 29 ++++++++
> .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 87 ++++++++++++++++++++++
> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 78 +++++++++++++++++++
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 37 ++++++++-
> 4 files changed, 230 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
Some nits below, otherwise:
Acked-by: Rob Herring <robh@xxxxxxxxxx>
>
> diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
> new file mode 100644
> index 000000000000..39cbe528b7de
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gxbb.txt
> @@ -0,0 +1,29 @@
> +Amlogic SD / eMMC controller for S905/GXBB family SoCs
> +
> +The MMC 5.1 compliant host controller on Amlogic provides the
> +interface for SD, eMMC and SDIO devices.
> +
> +This file documents the properties in addition to those available in
> +the MMC core bindings, documented by mmc.txt.
> +
> +Required properties:
> +- compatible : contains "amlogic,meson-gxbb-mmc"
> +- clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names.
> +- clock-names: Should contain the following:
> + "core" - Main peripheral bus clock
> + "clkin0" - Parent clock of internal mux
> + "clkin1" - Other parent clock of internal mux
> + The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the
> + clock rate requested by the MMC core.
> +
> +Example:
> +
> + sd_emmc_a: mmc@70000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x70000 0x0 0x2000>;
> + interrupts = < GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + pinctrl-0 = <&emmc_pins>;
> + };
> +
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 90a84c514d3d..2a9303e7fab8 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -73,6 +73,56 @@
> default-state = "off";
> };
> };
> +
> + tflash_vdd: regulator-tflash_vdd {
Use '-' not '_' in node names.
> + /*
> + * signal name from schematics: TFLASH_VDD_EN
> + */
> + compatible = "regulator-fixed";
> +
> + regulator-name = "TFLASH_VDD";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&gpio_ao GPIOAO_12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + tf_io: gpio-regulator-tf_io {
ditto
> + compatible = "regulator-gpio";
> +
> + regulator-name = "TF_IO";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + /*
> + * signal name from schematics: TF_3V3N_1V8_EN
> + */
> + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> +
> + states = <3300000 0
> + 1800000 1>;
> + };
> +
> + vcc1v8: regulator-vcc1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vcc3v3: regulator-vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> };
>
> &uart_AO {
> @@ -87,3 +137,40 @@
> pinctrl-names = "default";
> };
>
> +/* SD */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> +
> + vmmc-supply = <&tflash_vdd>;
> + vqmmc-supply = <&tf_io>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <8>;
> + cap-sd-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc3v3>;
> + vqmmc-supply = <&vcc1v8>;
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> index f4f30f674b4c..77c4d5eb48a2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> @@ -57,6 +57,47 @@
> device_type = "memory";
> reg = <0x0 0x0 0x0 0x40000000>;
> };
> +
> + vddio_card: gpio-regulator {
> + compatible = "regulator-gpio";
> +
> + regulator-name = "VDDIO_CARD";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> +
> + /* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
> + states = <1800000 0
> + 3300000 1>;
> + };
> +
> + vddio_boot: regulator-vddio_boot {
ditto
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_BOOT";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + vddao_3v3: regulator-vddao_3v3 {
ditto
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vcc_3v3: regulator-vcc_3v3 {
ditto
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> };
>
> /* This UART is brought out to the DB9 connector */
> @@ -72,3 +113,40 @@
> pinctrl-names = "default";
> };
>
> +/* SD card */
> +&sd_emmc_b {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <100000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_card>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>;
> + pinctrl-names = "default";
> +
> + bus-width = <8>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> index e502c24b0ac7..3723007146ac 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> @@ -45,6 +45,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/gpio/meson-gxbb-gpio.h>
> #include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
> +#include <dt-bindings/clock/gxbb-clkc.h>
>
> / {
> compatible = "amlogic,meson-gxbb";
> @@ -246,7 +247,8 @@
> mux {
> groups = "emmc_nand_d07",
> "emmc_cmd",
> - "emmc_clk";
> + "emmc_clk",
> + "emmc_ds";
> function = "emmc";
> };
> };
> @@ -329,6 +331,39 @@
> #address-cells = <2>;
> #size-cells = <2>;
> ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
> +
> + sd_emmc_a: mmc@70000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x70000 0x0 0x2000>;
> + interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_A>,
> + <&xtal>,
> + <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> + sd_emmc_b: mmc@72000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x72000 0x0 0x2000>;
> + interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_B>,
> + <&xtal>,
> + <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + status = "disabled";
> + };
> +
> + sd_emmc_c: mmc@74000 {
> + compatible = "amlogic,meson-gxbb-mmc";
> + reg = <0x0 0x74000 0x0 0x2000>;
> + interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&clkc CLKID_SD_EMMC_C>,
> + <&xtal>,
> + <&clkc CLKID_FCLK_DIV2>;
> + clock-names = "core", "clkin0", "clkin1";
> + status = "disabled";
> + };
> };
>
> ethmac: ethernet@c9410000 {
> --
> 2.9.3
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
