On Fri, Aug 26, 2016 at 02:45:49PM -0700, York Sun wrote: > From: York Sun <yorksun@xxxxxxxxxxxxx> > > SI5338 is a programmable clock generator. It has 4 sets of inputs, > PLL, multisynth and dividers to make 4 outputs. This driver splits > them into multiple clocks to comply with common clock framework. > > See Documentation/devicetree/bindings/clock/silabs,si5338.txt for > details. > > Signed-off-by: York Sun <yorksun@xxxxxxxxxxxxx> > CC: Mike Turquette <mturquette@xxxxxxxxxxxx> > CC: Sebastian Hesselbarth <sebastian.hesselbarth@xxxxxxxxx> > CC: Guenter Roeck <linux@xxxxxxxxxxxx> > CC: Andrey Filippov <andrey@xxxxxxxxxx> > CC: Paul Bolle <pebolle@xxxxxxxxxx> 7 versions before you decide to start cc'ing DT list? [...] > diff --git a/Documentation/devicetree/bindings/clock/silabs,si5338.txt b/Documentation/devicetree/bindings/clock/silabs,si5338.txt > new file mode 100644 > index 0000000..cc7ae8e > --- /dev/null > +++ b/Documentation/devicetree/bindings/clock/silabs,si5338.txt > @@ -0,0 +1,192 @@ > +Binding for Silicon Labs Si5338 programmable i2c clock generator. > + > +Reference > +[1] Si5338 Data Sheet > + http://www.silabs.com/Support%20Documents/TechnicalDocs/Si5338.pdf > + > +The Si5338 is a programmable i2c clock generators with up to 4 output > +clocks. It has 4 sets of possible input clocks > + > +IN1/IN2: differential > +IN3: single-ended > +IN4: single-ended > +IN5/IN6: differential > + > +Additionally, IN1/IN2 can be used as XTAL with different setting. > +The clock tree looks like below (without support of zero-delay) > + > + > + IN1/IN2 IN3 IN4 IN5/IN6 > + | | | | > + ------| | | | > + | | | | | > + | \ / \ / > + | \ / \ / > + | \ / \ / > + XTAL REFCLK FBCLK > + | | \ / | > + | | \ / | > + | | DIVREFCLK DIVFBCLK | > + | | \ / | > + | | \ / | > + | | \ / | > + | | PLL | > + | | / | | \ | > + | | / / \ \ | > + | | / / \ \ | > + | | / | | \ | > + | | | | | | | > + | | MS0 MS1 MS2 MS3 | > + | | | | | | | > + > + OUT0 OUT1 OUT2 OUT3 > + > +The output clock can choose from any of the above clock as its source, with > +exceptions: MS1 can only be used for OUT1, MS2 can only be used for OUT2, MS3 > +can only be used for OUT3. > + > +==I2C device node== > + > +Required properties: > +- compatible: shall be "silabs,si5338". > +- reg: i2c device address, shall be 0x60, 0x61, 0x70, or 0x71 > +- #clock-cells: shall be set to 1 for multiple outputs > +- clocks: list of parent clocks in the order of <xtal>, <in1/2>, <in3>, <in4>, > + <in5/6>. > + Note, xtal and in1/2 are mutually exclusive. Only one can be set. > +- clock-names: The name of the clocks in the same order. > +- #address-cells: shall be set to 1. > +- #size-cells: shall be set to 0. > +- silabs,pll-master: If PLL is used, pick one MS (0, 1, 2, or 3) to allow > + chaning PLL rate. This is arbitrary since MS0/1/2/3 share one PLL. > + PLL can be calculated backward to satisfy MS. This node is not > + required if PLL is not used, or if silabs,pll-vco is set. > + > +Optional properties if not set by platform driver: > +- silab,name-prefix: name prefix for si5338 > + If multiple si5338 chips exist, use name-prefix to form unique names. > + If omitted, i2c bus name will be used as the prefix. Drop this please. There should not be any need for it. > +- silab,ref-source: source of refclk, valid value is defined as > + #define SI5338_REF_SRC_CLKIN12 0 > + #define SI5338_REF_SRC_CLKIN3 1 > + #define SI5338_REF_SRC_XTAL 4 > +- silab,fb-source: source of fbclk, valid value is defined as > + #define SI5338_FB_SRC_CLKIN4 2 > + #define SI5338_FB_SRC_CLKIN56 3 > + #define SI5338_FB_SRC_NOCLK 5 > +- silabs,pll-source: source of pll, valid value is defined as > + #define SI5338_PFD_IN_REF_REFCLK 0 > + #define SI5338_PFD_IN_REF_FBCLK 1 > + #define SI5338_PFD_IN_REF_DIVREFCLK 2 > + #define SI5338_PFD_IN_REF_DIVFBCLK 3 > + #define SI5338_PFD_IN_REF_XOCLK 4 > + #define SI5338_PFD_IN_REF_NOCLK 5 > +- silabs,pll-vco: Specify VCO frequency for optimal ratios for all outputs. > + If specified, silabs,pll-master is ignored. > + > +==Child nodes== > + > +Each of the clock outputs can be configured individually by > +using a child node to the I2C device node. If a child node for a clock > +output is not set, platform driver has to set up. > + > +Required child node properties: > +- name: name for the child node > + It has to be unique. The name prefix is ignored. > + If using platform data and the name is not specificed, > + clkout0/1/2/3 will be used with name prefix. > +- reg: number of clock output. > + > +Optional child node properties: > +- silabs,drive-config: the configuration of output driver > + The valid value list is long. Please refer to soruce code. May be long, but needs to be documented here. I don't follow why you are using strings for the values here. > +- silabs,clock-source: source clock of the output divider > + #define SI5338_OUT_MUX_FBCLK 0 > + #define SI5338_OUT_MUX_REFCLK 1 > + #deinfe SI5338_OUT_MUX_DIVFBCLK 2 > + #deinfe SI5338_OUT_MUX_DIVREFCLK 3 > + #deinfe SI5338_OUT_MUX_XOCLK 4 > + #deinfe SI5338_OUT_MUX_MS0 5 > + #deinfe SI5338_OUT_MUX_MSN 6 /* MS0/1/2/3 */ > + #deinfe SI5338_OUT_MUX_NOCLK 7 > +- silabs,disable-state : clock output disable state, shall be > + #define SI5338_OUT_DIS_HIZ 0 > + #define SI5338_OUT_DIS_LOW 1 > + #define SI5338_OUT_DIS_HI 2 > + #define SI5338_OUT_DIS_ALWAYS_ON 3 > +- enabled: the output is enabled by default > + The existence of this node enables the output when the driver is loaded > + otherwise the clock is only enabled when used Drop this. Either platform code should claim this and enable the clock or use the critical clocks binding. > + > +==Example== > + > +/* 25MHz reference crystal */ > +ref25: ref25M { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <25000000>; > +}; > +clkin56: ref100M { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > +}; > +i2c-master-node { > + si5338: clock-generator@70 { > + compatible = "silabs,si5338"; > + reg = <0x70>; > + #address-cells = <1>; > + #size-cells = <0>; > + #clock-cells = <1>; > + > + /* connect xtal to 25MHz, in5/in6 to 100MHz */ > + clocks = <&ref25>, <0>, <0>, <0>, <&clkin56>; > + clock-names = "xtal", "in12", "in3", "in4", "in56"; > + > + /* connect xtal as source of refclk */ > + silab,ref-source = <SI5338_REF_SRC_XTAL>; > + > + /* connect in5/in6 as source of fbclk */ > + silab,fb-source = <SI5338_FB_SRC_CLKIN56>; > + > + /* connect divrefclk as source of pll */ > + silab,pll-source = <SI5338_PFD_IN_REF_DIVREFCLK>; > + > + /* Choose one MS for pll master */ > + silabs,pll-master = <0>; > + > + /* Specify pll-vco frequency. pll-master is ignored. */ > + silabs,pll-vco = <2450000000>; > + > + /* output */ > + clkout0 { reg property means you need a unit address. > + reg = <0>; > + silabs,drive-config = "1V8_LVDS"; > + silabs,clock-source = <SI5338_OUT_MUX_MS0>; > + silabs,disable-state = <SI5338_OUT_DIS_HIZ>; > + clock-frequency = <125000000>; > + }; > + clkout1 { > + reg = <1>; > + silabs,drive-config = "1V8_LVDS"; > + silabs,clock-source = <SI5338_OUT_MUX_MSN>; > + silabs,disable-state = <SI5338_OUT_DIS_HIZ>; > + clock-frequency = <125000000>; > + }; > + clkout2 { > + reg = <2>; > + silabs,drive-config = "1V8_LVDS"; > + silabs,clock-source = <SI5338_OUT_MUX_MSN>; > + silabs,disable-state = <SI5338_OUT_DIS_HIZ>; > + clock-frequency = <125000000>; > + }; > + clkout3 { > + reg = <3>; > + silabs,drive-config = "1V8_LVDS"; > + silabs,clock-source = <SI5338_OUT_MUX_MSN>; > + silabs,disable-state = <SI5338_OUT_DIS_HIZ>; > + clock-frequency = <125000000>; > + }; > + > + }; > +}; -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
