On 06/23/2016 07:43 PM, Archit Taneja wrote:
The APQ8016-sbc provides a HDMI output. The APQ8016 display block only provides a MIPI DSI output. So, the board has a ADV7533 DSI to HDMI encoder chip that sits between the DSI PHY output and the HDMI connector. Add the ADV7533 DT node under its I2C control bus, and tie the DSI output port to the ADV7533's input port.
and this one too? Thanks, Archit
Cc: Andy Gross <andy.gross@xxxxxxxxxx> Cc: Rob Herring <robh@xxxxxxxxxx> Cc: devicetree@xxxxxxxxxxxxxxx Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx> --- arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi | 48 +++++++++++++ arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 82 ++++++++++++++++++++++ 2 files changed, 130 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi index ee828a8..e1e6c6b 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi @@ -24,4 +24,52 @@ bias-pull-up; }; }; + + adv7533_int_active: adv533_int_active { + pinmux { + function = "gpio"; + pins = "gpio31"; + }; + pinconf { + pins = "gpio31"; + drive-strength = <16>; + bias-disable; + }; + }; + + adv7533_int_suspend: adv7533_int_suspend { + pinmux { + function = "gpio"; + pins = "gpio31"; + }; + pinconf { + pins = "gpio31"; + drive-strength = <2>; + bias-disable; + }; + }; + + adv7533_switch_active: adv7533_switch_active { + pinmux { + function = "gpio"; + pins = "gpio32"; + }; + pinconf { + pins = "gpio32"; + drive-strength = <16>; + bias-disable; + }; + }; + + adv7533_switch_suspend: adv7533_switch_suspend { + pinmux { + function = "gpio"; + pins = "gpio32"; + }; + pinconf { + pins = "gpio32"; + drive-strength = <2>; + bias-disable; + }; + }; }; diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 205ef89..5045695 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -59,6 +59,47 @@ /* On High speed expansion */ label = "HS-I2C2"; status = "okay"; + + adv_bridge: bridge@39 { + status = "okay"; + + compatible = "adi,adv7533"; + reg = <0x39>; + + interrupt-parent = <&msmgpio>; + interrupts = <31 2>; + + adi,dsi-lanes = <4>; + + pd-gpios = <&msmgpio 32 0>; + + avdd-supply = <&pm8916_l6>; + v1p2-supply = <&pm8916_l6>; + v3p3-supply = <&pm8916_l17>; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>; + pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7533_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7533_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; }; i2c@78ba000 { @@ -164,6 +205,36 @@ lpass@07708000 { status = "okay"; }; + + mdss@1a00000 { + status = "okay"; + + mdp@1a01000 { + status = "okay"; + }; + + dsi@1a98000 { + status = "okay"; + + vdda-supply = <&pm8916_l2>; + vddio-supply = <&pm8916_l6>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&adv7533_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; + + dsi-phy@1a98300 { + status = "okay"; + + vddio-supply = <&pm8916_l6>; + }; + }; }; usb2513 { @@ -178,6 +249,17 @@ pinctrl-names = "default"; pinctrl-0 = <&usb_id_default>; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7533_out>; + }; + }; + }; }; &smd_rpm_regulators {
-- Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html