On 24/08/16 14:37, Mirza Krak wrote:
> From: Mirza Krak <mirza.krak@xxxxxxxxx>
>
> Document the devicetree bindings for the Generic Memory Interface (GMI)
> bus driver found on Tegra SOCs.
>
> Signed-off-by: Mirza Krak <mirza.krak@xxxxxxxxx>
> ---
> Changes in v2:
> - Updated examples and some information based on comments from Jon Hunter.
>
> .../devicetree/bindings/bus/nvidia,tegra20-gmi.txt | 132 +++++++++++++++++++++
> 1 file changed, 132 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt
>
> diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt
> new file mode 100644
> index 0000000..8c1e15f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt
> @@ -0,0 +1,132 @@
> +Device tree bindings for NVIDIA Tegra Generic Memory Interface bus
> +
> +The Generic Memory Interface bus enables memory transfers between internal and
> +external memory. Can be used to attach various high speed devices such as
> +synchronous/asynchronous NOR, FPGA, UARTS and more.
> +
> +The actual devices are instantiated from the child nodes of a GMI node.
> +
> +Required properties:
> + - compatible : Should contain one of the following:
> + For Tegra20 must contain "nvidia,tegra20-gmi".
> + For Tegra30 must contain "nvidia,tegra30-gmi".
> + - reg: Should contain GMI controller registers location and length.
> + - clocks: Must contain an entry for each entry in clock-names.
> + - clock-names: Must include the following entries: "gmi"
> + - resets : Must contain an entry for each entry in reset-names.
> + - reset-names : Must include the following entries: "gmi"
> + - #address-cells: The number of cells used to represent physical base
> + addresses in the GMI address space. Should be 1.
> + - #size-cells: The number of cells used to represent the size of an address
> + range in the GMI address space. Should be 1.
> + - ranges: Must be set up to reflect the memory layout with three integer values
> + for each chip-select line in use (only one entry is supported, see below
> + comments):
> + <cs-number> <physical address of mapping> <size>
> +
> +Note that the GMI controller does not have any internal chip-select address
> +decoding, because of that chip-selects either need to be managed via software
> +or by employing external chip-select decoding logic.
> +
> +If external chip-select logic is used to support multiple devices it is assumed
> +that the devices use the same timing and so are probably the same type. It also
> +assumes that they can fit in the 256MB address range. In this case only one
> +child device is supported which represents the active chip-select line, see
> +examples for more insight.
> +
> +Required child cs node properties:
> + - reg: First entry should contain the active chip-select number
> +
> +Optional child cs node properties:
> +
> + - nvidia,snor-data-width-32bit: Use 32bit data-bus, default is 16bit.
> + - nvidia,snor-mux-mode: Enable address/data MUX mode.
> + - nvidia,snor-rdy-active-before-data: Assert RDY signal one cycle before data.
> + If omitted it will be asserted with data.
> + - nvidia,snor-rdy-inv: RDY signal is active high
> + - nvidia,snor-adv-inv: ADV signal is active high
> + - nvidia,snor-oe-inv: WE/OE signal is active high
> + - nvidia,snor-cs-inv: CS signal is active high
> +
> + Note that there is some special handling for the timing values.
> + From Tegra TRM:
> + Programming 0 means 1 clock cycle: actual cycle = programmed cycle + 1
> +
> + - nvidia,snor-muxed-width: Number of cycles MUX address/data asserted on the
> + bus. Valid values are 0-15, default is 1
> + - nvidia,snor-hold-width: Number of cycles CE stays asserted after the
> + de-assertion of WR_N (in case of SLAVE/MASTER Request) or OE_N
> + (in case of MASTER Request). Valid values are 0-15, default is 1
> + - nvidia,snor-adv-width: Number of cycles during which ADV stays asserted.
> + Valid values are 0-15, default is 1.
> + - nvidia,snor-ce-width: Number of cycles before CE is asserted.
> + Valid values are 0-15, default is 4
> + - nvidia,snor-we-width: Number of cycles during which WE stays asserted.
> + Valid values are 0-15, default is 1
> + - nvidia,snor-oe-width: Number of cycles during which OE stays asserted.
> + Valid values are 0-255, default is 1
> + - nvidia,snor-wait-width: Number of cycles before READY is asserted.
> + Valid values are 0-255, default is 3
> +
> +Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the
> +controllers with a simple-bus node since they are all connected to the same
> +chip-select (CS4), in this example external address decoding is provided:
> +
> +gmi@70090000 {
> + compatible = "nvidia,tegra20-gmi";
> + reg = <0x70009000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + clocks = <&tegra_car TEGRA20_CLK_NOR>;
> + clock-names = "gmi";
> + resets = <&tegra_car 42>;
> + reset-names = "gmi";
> + ranges = <4 0x48000000 0x7ffffff>;
> +
> + status = "disabled";
> +
> + bus@4 {
> + compatible = "simple-bus";
> + reg = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 4 0x40100>;
Does this work? I tried to add an example like this and I got ...
Warning (reg_format): "reg" property in /gmi@70009000/bus@4 has invalid
length (4 bytes) (#address-cells == 1, #size-cells == 1)
I am wondering if we should just following the arm,pl172 example and
have ...
cs4 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
nvidia,snor-cs = <4>;
nvidia,snor-mux-mode;
nvidia,snor-adv-inv;
can@0 {
reg = <0 0x100>;
...
};
...
};
Cheers
Jon
--
nvpublic
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
