[PATCH 1/2] hwmon: (max6650) Allow fan shutdown and initial rpm target

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




The fan can be stopped by writing "3" to pwm1_enable in sysfs.

Add devicetree property for early initialization of the fan controller
to prevent overheating, for example when resetting the board while the
fan was completely turned off.

Also improve error reporting, I2C failures were ignored while writing
new values.

Signed-off-by: Mike Looijmans <mike.looijmans@xxxxxxxx>
---
 Documentation/hwmon/max6650 |   1 +
 drivers/hwmon/max6650.c     | 108 +++++++++++++++++++++++++++-----------------
 2 files changed, 68 insertions(+), 41 deletions(-)

diff --git a/Documentation/hwmon/max6650 b/Documentation/hwmon/max6650
index 58d9644..dff1d29 100644
--- a/Documentation/hwmon/max6650
+++ b/Documentation/hwmon/max6650
@@ -34,6 +34,7 @@ fan3_input	ro	"
 fan4_input	ro	"
 fan1_target	rw	desired fan speed in RPM (closed loop mode only)
 pwm1_enable	rw	regulator mode, 0=full on, 1=open loop, 2=closed loop
+			3=off
 pwm1		rw	relative speed (0-255), 255=max. speed.
 			Used in open loop mode only.
 fan1_div	rw	sets the speed range the inputs can handle. Legal
diff --git a/drivers/hwmon/max6650.c b/drivers/hwmon/max6650.c
index c87517a..a993b44 100644
--- a/drivers/hwmon/max6650.c
+++ b/drivers/hwmon/max6650.c
@@ -185,6 +185,30 @@ static struct max6650_data *max6650_update_device(struct device *dev)
 	return data;
 }
 
+/*
+ * Change the operating mode of the chip (if needed).
+ * mode is one of the MAX6650_CFG_MODE_* values.
+ */
+static int max6650_set_operating_mode(struct max6650_data *data, u8 mode)
+{
+	int result;
+	u8 config = data->config;
+
+	if (mode == (config & MAX6650_CFG_MODE_MASK))
+		return 0;
+
+	config = (config & ~MAX6650_CFG_MODE_MASK) | mode;
+
+	result = i2c_smbus_write_byte_data(data->client, MAX6650_REG_CONFIG,
+					   config);
+	if (result < 0)
+		return result;
+
+	data->config = config;
+
+	return 0;
+}
+
 static ssize_t get_fan(struct device *dev, struct device_attribute *devattr,
 		       char *buf)
 {
@@ -266,18 +290,12 @@ static ssize_t get_target(struct device *dev, struct device_attribute *devattr,
 	return sprintf(buf, "%d\n", rpm);
 }
 
-static ssize_t set_target(struct device *dev, struct device_attribute *devattr,
-			 const char *buf, size_t count)
+static int max6650_set_target(struct max6650_data *data, unsigned long rpm)
 {
-	struct max6650_data *data = dev_get_drvdata(dev);
-	struct i2c_client *client = data->client;
 	int kscale, ktach;
-	unsigned long rpm;
-	int err;
 
-	err = kstrtoul(buf, 10, &rpm);
-	if (err)
-		return err;
+	if (rpm == 0)
+		return max6650_set_operating_mode(data, MAX6650_CFG_MODE_OFF);
 
 	rpm = clamp_val(rpm, FAN_RPM_MIN, FAN_RPM_MAX);
 
@@ -288,8 +306,6 @@ static ssize_t set_target(struct device *dev, struct device_attribute *devattr,
 	 *     KTACH = [(fCLK x KSCALE) / (256 x FanSpeed)] - 1
 	 */
 
-	mutex_lock(&data->update_lock);
-
 	kscale = DIV_FROM_REG(data->config);
 	ktach = ((clock * kscale) / (256 * rpm / 60)) - 1;
 	if (ktach < 0)
@@ -298,10 +314,30 @@ static ssize_t set_target(struct device *dev, struct device_attribute *devattr,
 		ktach = 255;
 	data->speed = ktach;
 
-	i2c_smbus_write_byte_data(client, MAX6650_REG_SPEED, data->speed);
+	return i2c_smbus_write_byte_data(data->client, MAX6650_REG_SPEED,
+					 data->speed);
+}
+
+static ssize_t set_target(struct device *dev, struct device_attribute *devattr,
+			 const char *buf, size_t count)
+{
+	struct max6650_data *data = dev_get_drvdata(dev);
+	unsigned long rpm;
+	int err;
+
+	err = kstrtoul(buf, 10, &rpm);
+	if (err)
+		return err;
+
+	mutex_lock(&data->update_lock);
+
+	err = max6650_set_target(data, rpm);
 
 	mutex_unlock(&data->update_lock);
 
+	if (err < 0)
+		return err;
+
 	return count;
 }
 
@@ -355,12 +391,11 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *devattr,
 		data->dac = 180 - (180 * pwm)/255;
 	else
 		data->dac = 76 - (76 * pwm)/255;
-
-	i2c_smbus_write_byte_data(client, MAX6650_REG_DAC, data->dac);
+	err = i2c_smbus_write_byte_data(client, MAX6650_REG_DAC, data->dac);
 
 	mutex_unlock(&data->update_lock);
 
-	return count;
+	return err < 0 ? err : count;
 }
 
 /*
@@ -369,14 +404,14 @@ static ssize_t set_pwm(struct device *dev, struct device_attribute *devattr,
  * 0 = Fan always on
  * 1 = Open loop, Voltage is set according to speed, not regulated.
  * 2 = Closed loop, RPM for all fans regulated by fan1 tachometer
+ * 3 = Fan off
  */
-
 static ssize_t get_enable(struct device *dev, struct device_attribute *devattr,
 			  char *buf)
 {
 	struct max6650_data *data = max6650_update_device(dev);
 	int mode = (data->config & MAX6650_CFG_MODE_MASK) >> 4;
-	int sysfs_modes[4] = {0, 1, 2, 1};
+	int sysfs_modes[4] = {0, 3, 2, 1};
 
 	return sprintf(buf, "%d\n", sysfs_modes[mode]);
 }
@@ -385,25 +420,25 @@ static ssize_t set_enable(struct device *dev, struct device_attribute *devattr,
 			  const char *buf, size_t count)
 {
 	struct max6650_data *data = dev_get_drvdata(dev);
-	struct i2c_client *client = data->client;
-	int max6650_modes[3] = {0, 3, 2};
 	unsigned long mode;
 	int err;
+	const u8 max6650_modes[] = {
+		MAX6650_CFG_MODE_ON,
+		MAX6650_CFG_MODE_OPEN_LOOP,
+		MAX6650_CFG_MODE_CLOSED_LOOP,
+		MAX6650_CFG_MODE_OFF,
+		};
 
 	err = kstrtoul(buf, 10, &mode);
 	if (err)
 		return err;
 
-	if (mode > 2)
+	if (mode >= ARRAY_SIZE(max6650_modes))
 		return -EINVAL;
 
 	mutex_lock(&data->update_lock);
 
-	data->config = i2c_smbus_read_byte_data(client, MAX6650_REG_CONFIG);
-	data->config = (data->config & ~MAX6650_CFG_MODE_MASK)
-		       | (max6650_modes[mode] << 4);
-
-	i2c_smbus_write_byte_data(client, MAX6650_REG_CONFIG, data->config);
+	max6650_set_operating_mode(data, max6650_modes[mode]);
 
 	mutex_unlock(&data->update_lock);
 
@@ -582,6 +617,7 @@ static int max6650_init_client(struct max6650_data *data,
 	int err = -EIO;
 	u32 voltage;
 	u32 prescale;
+	u32 target_rpm;
 
 	if (of_property_read_u32(dev->of_node, "maxim,fan-microvolt",
 				 &voltage))
@@ -642,22 +678,6 @@ static int max6650_init_client(struct max6650_data *data,
 		 (config & MAX6650_CFG_V12) ? 12 : 5,
 		 1 << (config & MAX6650_CFG_PRESCALER_MASK));
 
-	/*
-	 * If mode is set to "full off", we change it to "open loop" and
-	 * set DAC to 255, which has the same effect. We do this because
-	 * there's no "full off" mode defined in hwmon specifications.
-	 */
-
-	if ((config & MAX6650_CFG_MODE_MASK) == MAX6650_CFG_MODE_OFF) {
-		dev_dbg(dev, "Change mode to open loop, full off.\n");
-		config = (config & ~MAX6650_CFG_MODE_MASK)
-			 | MAX6650_CFG_MODE_OPEN_LOOP;
-		if (i2c_smbus_write_byte_data(client, MAX6650_REG_DAC, 255)) {
-			dev_err(dev, "DAC write error, aborting.\n");
-			return err;
-		}
-	}
-
 	if (i2c_smbus_write_byte_data(client, MAX6650_REG_CONFIG, config)) {
 		dev_err(dev, "Config write error, aborting.\n");
 		return err;
@@ -666,6 +686,12 @@ static int max6650_init_client(struct max6650_data *data,
 	data->config = config;
 	data->count = i2c_smbus_read_byte_data(client, MAX6650_REG_COUNT);
 
+	if (!of_property_read_u32(client->dev.of_node, "maxim,fan-target-rpm",
+				  &target_rpm)) {
+		max6650_set_target(data, target_rpm);
+		max6650_set_operating_mode(data, MAX6650_CFG_MODE_CLOSED_LOOP);
+	}
+
 	return 0;
 }
 
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux