Re: [PATCH 6/7] arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Krzysztof,

On 2016년 08월 17일 15:42, Krzysztof Kozlowski wrote:
> On 08/16/2016 08:35 AM, Chanwoo Choi wrote:
>> This patch adds the Device Tree source for Exynos5433-based Samsung TM2 board.
>> This board fully support the all things for mobile target.
>>
>> This patch supports the following devices:
>> 1. basic SoC
>> - Initial booting for Samsung Exynos5433 SoC
>> - DRAM LPDDR3 (3GB)
>> - eMMC (32GB)
>> - ARM architecture timer
>>
>> 2. power management devices
>> - Sasmung S2MPS13 PMIC for the power supply
>> - CPUFREQ for big.LITTLE cores
>> - TMU for big.LITTLE cores and GPU
>> - ADC with thermistor to measure the temperature of AP/Battery/Charger
>> - Maxim MAX77843 Interface PMIC (MUIC/Fuel-gauge/Charger/Haptic/LED/Regulator)
>>
>> 3. sound devices
>> - I2S for sound bus
>> - LPASS for sound power control
>> - Wolfson WM5110 for sound codec
>> - Maxim MAX98504 for speaker amplifier
>> - TM2 ASoC Machine device driver node
>>
>> 3. display devices
>> - DECON, DSI and MIC for the panel output
>>
>> 4. usb devices
>> - USB 3.0 DRD (Dual Role Device)
>> - USB 3.0 Host controller
>>
>> 5. storage devices
>> - MSHC (obile Storae Host Controller) for eMMC device
> 
> Mobile Storage

OK.

> 
>>
>> 6. misc devices
>> - gpio-keys (power, volume up/down, home key)
>> - PWM (Pulse Width Modulation Timer)
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
>> Signed-off-by: Seung-Woo Kim <sw0312.kim@xxxxxxxxxxx>
>> Signed-off-by: Joonyoung Shim <jy0922.shim@xxxxxxxxxxx>
>> Signed-off-by: Inki Dae <inki.dae@xxxxxxxxxxx>
>> Signed-off-by: Jonghwa Lee <jonghwa3.lee@xxxxxxxxxxx>
>> Signed-off-by: Beomho Seo <beomho.seo@xxxxxxxxxxx>
>> Signed-off-by: Jaewon Kim <jaewon02.kim@xxxxxxxxxxx>
>> Signed-off-by: Hyungwon Hwang <human.hwang@xxxxxxxxxxx>
>> Signed-off-by: Inha Song <ideal.song@xxxxxxxxxxx>
>> Signed-off-by: Ingi kim <ingi2.kim@xxxxxxxxxxx>
>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
>> Signed-off-by: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
>> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@xxxxxxxxxxx>
>> ---
>>  .../bindings/arm/samsung/samsung-boards.txt        |    1 +
>>  arch/arm64/boot/dts/exynos/Makefile                |    5 +-
>>  arch/arm64/boot/dts/exynos/exynos5433-tm2.dts      | 1003 ++++++++++++++++++++
>>  3 files changed, 1008 insertions(+), 1 deletion(-)
>>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> index 0ea7f14ef294..c704b4bf6137 100644
>> --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> @@ -15,6 +15,7 @@ Required root node properties:
>>  	- "samsung,xyref5260"	- for Exynos5260-based Samsung board.
>>  	- "samsung,smdk5410"	- for Exynos5410-based Samsung SMDK5410 eval board.
>>  	- "samsung,smdk5420"	- for Exynos5420-based Samsung SMDK5420 eval board.
>> +	- "samsung,tm2"		- for Exynos5333-based Samsung TM2 board.
>>  	- "samsung,sd5v1"	- for Exynos5440-based Samsung board.
>>  	- "samsung,ssdk5440"	- for Exynos5440-based Samsung board.
>>  
>> diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
>> index 50c9b9383cfa..7ddea53769a7 100644
>> --- a/arch/arm64/boot/dts/exynos/Makefile
>> +++ b/arch/arm64/boot/dts/exynos/Makefile
>> @@ -1,4 +1,7 @@
>> -dtb-$(CONFIG_ARCH_EXYNOS) += exynos7-espresso.dtb
>> +dtb-$(CONFIG_ARCH_EXYNOS) += \
>> +	exynos5433-tm2.dtb	\
>> +	exynos5433-tm2e.dtb	\
>> +	exynos7-espresso.dtb
>>  
>>  always		:= $(dtb-y)
>>  subdir-y	:= $(dts-dirs)
>> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
>> new file mode 100644
>> index 000000000000..3e497b0d0015
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
>> @@ -0,0 +1,1003 @@
>> +/*
>> + * SAMSUNG Exynos5433 TM2 board device tree source
>> + *
>> + * Copyright (c) 2016 Samsung Electronics Co., Ltd.
>> + *
>> + * Device tree source file for Samsung's TM2 board which is based on
>> + * Samsung Exynos5433 SoC.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +/dts-v1/;
>> +#include "exynos5433.dtsi"
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +
>> +/ {
>> +	model = "Samsung TM2 board";
>> +	compatible = "samsung,exynos5433-tm2", "samsung,exynos5433";
>> +
>> +	aliases {
>> +		i2c0 = &hsi2c_0;
>> +		i2c1 = &hsi2c_1;
>> +		i2c2 = &hsi2c_2;
>> +		i2c3 = &hsi2c_3;
>> +		i2c4 = &hsi2c_4;
>> +		i2c5 = &hsi2c_5;
>> +		i2c6 = &hsi2c_6;
>> +		i2c7 = &hsi2c_7;
>> +		i2c8 = &hsi2c_8;
>> +		i2c9 = &hsi2c_9;
>> +		i2c10 = &hsi2c_10;
>> +		i2c11 = &hsi2c_11;
>> +		mshc0 = &mshc_0;
>> +		mshc1 = &mshc_1;
>> +		mshc2 = &mshc_2;
>> +		pinctrl0 = &pinctrl_alive;
>> +		pinctrl1 = &pinctrl_aud;
>> +		pinctrl2 = &pinctrl_cpif;
>> +		pinctrl3 = &pinctrl_ese;
>> +		pinctrl4 = &pinctrl_finger;
>> +		pinctrl5 = &pinctrl_fsys;
>> +		pinctrl6 = &pinctrl_imem;
>> +		pinctrl7 = &pinctrl_nfc;
>> +		pinctrl8 = &pinctrl_peric;
>> +		pinctrl9 = &pinctrl_touch;
>> +		serial0 = &serial_0;
>> +		serial1 = &serial_1;
>> +		serial2 = &serial_2;
>> +		serial3 = &serial_3;
>> +		spi0 = &spi_0;
>> +		spi1 = &spi_1;
>> +		spi2 = &spi_2;
>> +		spi3 = &spi_3;
>> +		spi4 = &spi_4;
>> +		usbdrdphy0 = &usbdrd30_phy;
>> +	};
>> +
>> +	chosen {
>> +		stdout-path = &serial_1;
>> +	};
>> +
>> +	memory@20000000 {
>> +		device_type = "memory";
>> +		reg = <0x0 0x20000000 0x0 0xc0000000>;
>> +	};
>> +
>> +	gpio_keys {
>> +		compatible = "gpio-keys";
>> +
>> +		power_key {
>> +			gpios = <&gpa2 7 1>;
> 
> s/1/GPIO_ACTIVE_LOW/

OK.

> 
>> +			linux,code = <KEY_POWER>;
>> +			label = "power key";
>> +			debounce-interval = <10>;
>> +			gpio-key,wakeup;
>> +		};
>> +
>> +		volume_up_key {
>> +			gpios = <&gpa2 0 1>;
> 
> s/1/GPIO_ACTIVE_LOW/

OK.

> 
>> +			linux,code = <KEY_VOLUMEUP>;
>> +			label = "volume-up key";
>> +			debounce-interval = <10>;
>> +		};
>> +
>> +		volume_down_key {
>> +			gpios = <&gpa2 1 1>;
> 
> s/1/GPIO_ACTIVE_LOW/

OK.

> 
>> +			linux,code = <KEY_VOLUMEDOWN>;
>> +			label = "volume-down key";
>> +			debounce-interval = <10>;
>> +		};
>> +
>> +		homepage_key {
>> +			gpios = <&gpa0 3 1>;
> 
> s/1/GPIO_ACTIVE_LOW/

OK.

> 
>> +			linux,code = <KEY_MENU>;
>> +			label = "homepage key";
>> +			debounce-interval = <10>;
>> +		};
>> +	};
>> +
>> +	i2c_max98504: i2c-gpio-0 {
>> +		compatible = "i2c-gpio";
>> +		gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
>> +			 &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
>> +		i2c-gpio,delay-us = <2>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		status = "okay";
>> +
>> +		max98504: max98504@31 {
>> +			compatible = "maxim,max98504";
>> +			reg = <0x31>;
>> +			maxim,rx-path = <1>;
>> +			maxim,tx-path = <1>;
>> +			maxim,tx-channel-mask = <3>;
>> +			maxim,tx-channel-source = <2>;
>> +		};
>> +	};
>> +
>> +	sound {
>> +		compatible = "samsung,tm2-audio";
>> +		audio-codec = <&wm5110>;
>> +		i2s-controller = <&i2s0>;
>> +		audio-amplifier = <&max98504>;
>> +		mic-bias-gpios = <&gpr3 2 0>;
> 
> s/0/GPIO_ACTIVE_HIGH/

OK.

> 
>> +		model = "wm5110";
>> +		samsung,audio-routing =
>> +			/* Headphone */
>> +			"HP", "HPOUT1L",
>> +			"HP", "HPOUT1R",
>> +
>> +			/* Speaker */
>> +			"SPK", "SPKOUT",
>> +			"SPKOUT", "HPOUT2L",
>> +			"SPKOUT", "HPOUT2R",
>> +
>> +			/* Receiver */
>> +			"RCV", "HPOUT3L",
>> +			"RCV", "HPOUT3R";
>> +		status = "okay";
>> +	};
>> +};
>> +
>> +&adc {
>> +	vdd-supply = <&ldo3_reg>;
>> +	status = "okay";
>> +
>> +	thermistor-ap {
>> +		compatible = "ntc,ncp03wf104";
>> +		pullup-uv = <1800000>;
>> +		pullup-ohm = <100000>;
>> +		pulldown-ohm = <0>;
>> +		io-channels = <&adc 0>;
>> +	};
>> +
>> +	thermistor_battery: thermistor-battery {
>> +		compatible = "ntc,ncp03wf104";
>> +		pullup-uv = <1800000>;
>> +		pullup-ohm = <100000>;
>> +		pulldown-ohm = <0>;
>> +		io-channels = <&adc 1>;
>> +		#thermal-sensor-cells = <0>;
>> +	};
>> +
>> +	thermistor-charger {
>> +		compatible = "ntc,ncp03wf104";
>> +		pullup-uv = <1800000>;
>> +		pullup-ohm = <100000>;
>> +		pulldown-ohm = <0>;
>> +		io-channels = <&adc 2>;
>> +	};
>> +};
>> +
>> +&cpu0 {
>> +	cpu-supply = <&buck3_reg>;
>> +};
>> +
>> +&cpu4 {
>> +	cpu-supply = <&buck2_reg>;
>> +};
>> +
>> +&decon {
>> +	status = "okay";
>> +	iommu-reserved-mapping = <0x20000000 0x20000000 0xc0000000>;
>> +
>> +	i80-if-timings {
>> +	};
>> +};
>> +
>> +&dsi {
>> +	status = "okay";
>> +	vddcore-supply = <&ldo6_reg>;
>> +	vddio-supply = <&ldo7_reg>;
>> +	samsung,pll-clock-frequency = <24000000>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&te_irq>;
>> +
>> +	ports {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		port@1 {
>> +			reg = <1>;
>> +
>> +			dsi_out: endpoint {
>> +				samsung,burst-clock-frequency = <512000000>;
>> +				samsung,esc-clock-frequency = <16000000>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&hsi2c_0 {
>> +	status = "okay";
>> +	clock-frequency = <2500000>;
>> +
>> +	s2mps13_pmic@66 {
>> +		compatible = "samsung,s2mps13-pmic";
>> +		interrupt-parent = <&gpa0>;
>> +		interrupts = <7 0>;
> 
> s/0/IRQ_TYPE_NONE/

OK.

> 
>> +		reg = <0x66>;
>> +		wakeup;
> 
> I think there is no such "wakeup" property.

I'll remove it.

> 
>> +		samsung,s2mps11-wrstbi-ground;
>> +
>> +		s2mps13_osc: clocks {
>> +			compatible = "samsung,s2mps13-clk";
>> +			#clock-cells = <1>;
>> +			clock-output-names = "s2mps13_ap", "s2mps13_cp",
>> +				"s2mps13_bt";
>> +		};
>> +
>> +		regulators {
>> +			ldo1_reg: LDO1 {
>> +				regulator-name = "VDD_ALIVE_0.9V_AP";
>> +				regulator-min-microvolt = <900000>;
>> +				regulator-max-microvolt = <900000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo2_reg: LDO2 {
>> +				regulator-name = "VDDQ_MMC2_2.8V_AP";
>> +				regulator-min-microvolt = <2800000>;
>> +				regulator-max-microvolt = <2800000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo3_reg: LDO3 {
>> +				regulator-name = "VDD1_E_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo4_reg: LDO4 {
>> +				regulator-name = "VDD10_MIF_PLL_1.0V_AP";
>> +				regulator-min-microvolt = <1300000>;
>> +				regulator-max-microvolt = <1300000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo5_reg: LDO5 {
>> +				regulator-name = "VDD10_DPLL_1.0V_AP";
>> +				regulator-min-microvolt = <1000000>;
>> +				regulator-max-microvolt = <1000000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo6_reg: LDO6 {
>> +				regulator-name = "VDD10_MIPI2L_1.0V_AP";
>> +				regulator-min-microvolt = <1000000>;
>> +				regulator-max-microvolt = <1000000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo7_reg: LDO7 {
>> +				regulator-name = "VDD18_MIPI2L_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo8_reg: LDO8 {
>> +				regulator-name = "VDD18_LLI_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo9_reg: LDO9 {
>> +				regulator-name = "VDD18_ABB_ETC_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo10_reg: LDO10 {
>> +				regulator-name = "VDD33_USB30_3.0V_AP";
>> +				regulator-min-microvolt = <3000000>;
>> +				regulator-max-microvolt = <3000000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo11_reg: LDO11 {
>> +				regulator-name = "VDD_INT_M_1.0V_AP";
>> +				regulator-min-microvolt = <1000000>;
>> +				regulator-max-microvolt = <1000000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo12_reg: LDO12 {
>> +				regulator-name = "VDD_KFC_M_1.1V_AP";
>> +				regulator-min-microvolt = <800000>;
>> +				regulator-max-microvolt = <1350000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo13_reg: LDO13 {
>> +				regulator-name = "VDD_G3D_M_0.95V_AP";
>> +				regulator-min-microvolt = <950000>;
>> +				regulator-max-microvolt = <950000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo14_reg: LDO14 {
>> +				regulator-name = "VDDQ_M1_LDO_1.2V_AP";
>> +				regulator-min-microvolt = <1200000>;
>> +				regulator-max-microvolt = <1200000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo15_reg: LDO15 {
>> +				regulator-name = "VDDQ_M2_LDO_1.2V_AP";
>> +				regulator-min-microvolt = <1200000>;
>> +				regulator-max-microvolt = <1200000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			ldo16_reg: LDO16 {
>> +				regulator-name = "VDDQ_EFUSE";
>> +				regulator-min-microvolt = <1400000>;
>> +				regulator-max-microvolt = <3400000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo17_reg: LDO17 {
>> +				regulator-name = "V_TFLASH_2.8V_AP";
>> +				regulator-min-microvolt = <2800000>;
>> +				regulator-max-microvolt = <2800000>;
>> +			};
>> +
>> +			ldo18_reg: LDO18 {
>> +				regulator-name = "V_CODEC_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo19_reg: LDO19 {
>> +				regulator-name = "VDDA_1.8V_COMP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo20_reg: LDO20 {
>> +				regulator-name = "VCC_2.8V_AP";
>> +				regulator-min-microvolt = <2800000>;
>> +				regulator-max-microvolt = <2800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo21_reg: LDO21 {
>> +				regulator-name = "VT_CAM_1.8V";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +			};
>> +
>> +			ldo22_reg: LDO22 {
>> +				regulator-name = "CAM_IO_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +			};
>> +
>> +			ldo23_reg: LDO23 {
>> +				regulator-name = "CAM_SEN_CORE_1.2V_AP";
>> +				regulator-min-microvolt = <1050000>;
>> +				regulator-max-microvolt = <1200000>;
>> +			};
>> +
>> +			ldo24_reg: LDO24 {
>> +				regulator-name = "VT_CAM_1.2V";
>> +				regulator-min-microvolt = <1200000>;
>> +				regulator-max-microvolt = <1200000>;
>> +			};
>> +
>> +			ldo25_reg: LDO25 {
>> +				regulator-name = "CAM_SEN_A2.8V_AP";
>> +				regulator-min-microvolt = <2800000>;
>> +				regulator-max-microvolt = <2800000>;
>> +			};
>> +
>> +			ldo26_reg: LDO26 {
>> +				regulator-name = "CAM_AF_2.8V_AP";
>> +				regulator-min-microvolt = <2800000>;
>> +				regulator-max-microvolt = <2800000>;
>> +			};
>> +
>> +			ldo27_reg: LDO27 {
>> +				regulator-name = "VCC_3.0V_LCD_AP";
>> +				regulator-min-microvolt = <3000000>;
>> +				regulator-max-microvolt = <3000000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo28_reg: LDO28 {
>> +				regulator-name = "VCC_1.8V_LCD_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo29_reg: LDO29 {
>> +				regulator-name = "VT_CAM_2.8V";
>> +				regulator-min-microvolt = <3000000>;
>> +				regulator-max-microvolt = <3000000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo30_reg: LDO30 {
>> +				regulator-name = "TSP_AVDD_3.3V_AP";
>> +				regulator-min-microvolt = <3300000>;
>> +				regulator-max-microvolt = <3300000>;
>> +			};
>> +
>> +			ldo31_reg: LDO31 {
>> +				regulator-name = "TSP_VDD_1.85V_AP";
>> +				regulator-min-microvolt = <1850000>;
>> +				regulator-max-microvolt = <1850000>;
>> +				regulator-boot-on;
>> +			};
>> +
>> +			ldo32_reg: LDO32 {
>> +				regulator-name = "VTOUCH_1.8V_AP";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-boot-on;
>> +			};
>> +
>> +			ldo33_reg: LDO33 {
>> +				regulator-name = "VTOUCH_LED_3.3V";
>> +				regulator-min-microvolt = <2500000>;
>> +				regulator-max-microvolt = <3300000>;
>> +				regulator-ramp-delay = <12500>;
>> +			};
>> +
>> +			ldo34_reg: LDO34 {
>> +				regulator-name = "VCC_1.8V_MHL_AP";
>> +				regulator-min-microvolt = <1000000>;
>> +				regulator-max-microvolt = <2100000>;
>> +			};
>> +
>> +			ldo35_reg: LDO35 {
>> +				regulator-name = "OIS_VM_2.8V";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <2800000>;
>> +			};
>> +
>> +			ldo36_reg: LDO36 {
>> +				regulator-name = "VSIL_1.0V";
>> +				regulator-min-microvolt = <1000000>;
>> +				regulator-max-microvolt = <1000000>;
>> +			};
>> +
>> +			ldo37_reg: LDO37 {
>> +				regulator-name = "VF_1.8V";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			ldo38_reg: LDO38 {
>> +				regulator-name = "VCC_3.0V_MOTOR_AP";
>> +				regulator-min-microvolt = <3000000>;
>> +				regulator-max-microvolt = <3000000>;
>> +			};
>> +
>> +			ldo39_reg: LDO39 {
>> +				regulator-name = "V_HRM_1.8V";
>> +				regulator-min-microvolt = <1800000>;
>> +				regulator-max-microvolt = <1800000>;
>> +			};
>> +
>> +			ldo40_reg: LDO40 {
>> +				regulator-name = "V_HRM_3.3V";
>> +				regulator-min-microvolt = <3300000>;
>> +				regulator-max-microvolt = <3300000>;
>> +			};
>> +
>> +			buck1_reg: BUCK1 {
>> +				regulator-name = "VDD_MIF_0.9V_AP";
>> +				regulator-min-microvolt = <600000>;
>> +				regulator-max-microvolt = <1500000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			buck2_reg: BUCK2 {
>> +				regulator-name = "VDD_EGL_1.0V_AP";
>> +				regulator-min-microvolt = <900000>;
>> +				regulator-max-microvolt = <1300000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			buck3_reg: BUCK3 {
>> +				regulator-name = "VDD_KFC_1.0V_AP";
>> +				regulator-min-microvolt = <800000>;
>> +				regulator-max-microvolt = <1200000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			buck4_reg: BUCK4 {
>> +				regulator-name = "VDD_INT_0.95V_AP";
>> +				regulator-min-microvolt = <600000>;
>> +				regulator-max-microvolt = <1500000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			buck5_reg: BUCK5 {
>> +				regulator-name = "VDD_DISP_CAM0_0.9V_AP";
>> +				regulator-min-microvolt = <600000>;
>> +				regulator-max-microvolt = <1500000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			buck6_reg: BUCK6 {
>> +				regulator-name = "VDD_G3D_0.9V_AP";
>> +				regulator-min-microvolt = <600000>;
>> +				regulator-max-microvolt = <1500000>;
>> +				regulator-always-on;
>> +				regulator-state-mem {
>> +					regulator-off-in-suspend;
>> +				};
>> +			};
>> +
>> +			buck7_reg: BUCK7 {
>> +				regulator-name = "VDD_MEM1_1.2V_AP";
>> +				regulator-min-microvolt = <1200000>;
>> +				regulator-max-microvolt = <1200000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			buck8_reg: BUCK8 {
>> +				regulator-name = "VDD_LLDO_1.35V_AP";
>> +				regulator-min-microvolt = <1350000>;
>> +				regulator-max-microvolt = <3300000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			buck9_reg: BUCK9 {
>> +				regulator-name = "VDD_MLDO_2.0V_AP";
>> +				regulator-min-microvolt = <1350000>;
>> +				regulator-max-microvolt = <3300000>;
>> +				regulator-always-on;
>> +			};
>> +
>> +			buck10_reg: BUCK10 {
>> +				regulator-name = "vdd_mem2";
>> +				regulator-min-microvolt = <550000>;
>> +				regulator-max-microvolt = <1500000>;
>> +				regulator-always-on;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&hsi2c_8 {
>> +	status = "okay";
>> +
>> +	max77843@66 {
>> +		compatible = "samsung,max77843";
> 
> There is no such compatible.

It is my mistake. I'll fix it using "maxim,max77843"

> 
>> +		interrupt-parent = <&gpa1>;
>> +		interrupts = <5 2>;
> 
> IRQ_TYPE_EDGE_FALLING

OK.

> 
>> +		reg = <0x66>;
>> +		wakeup;
> 
> Ditto - wakeup.

I'll remove it.

> 
>> +
>> +		muic: max77843-muic {
>> +			compatible = "maxim,max77843-muic";
>> +		};
>> +
>> +		regulators {
>> +			compatible = "maxim,max77843-regulator";
> 
> BTW, It's a pity that max77843 submission was not finished. These
> compatibles are not documented. Also the charger driver did not reach
> mainline. The fuelgauge probably has wrong compatible in MFD driver.

The "max77843-regulator"[1] was merged to driver/regulator/max77693-regulator.c.
[1] 9e9a08e86733d (regulator: max77693: Add support for MAX77843 device)

I know the charger/fuel-gauge was not finished. I'll again post them. So,
this patch don't include the charger/fuel-gauge dt node.

> 
>> +			safeout1_reg: SAFEOUT1 {
>> +				regulator-name = "SAFEOUT1";
>> +				regulator-min-microvolt = <3300000>;
>> +				regulator-max-microvolt = <4950000>;
>> +			};
>> +
>> +			safeout2_reg: SAFEOUT2 {
>> +				regulator-name = "SAFEOUT2";
>> +				regulator-min-microvolt = <3300000>;
>> +				regulator-max-microvolt = <4950000>;
>> +			};
>> +
>> +			charger_reg: CHARGER {
>> +				regulator-name = "CHARGER";
>> +				regulator-min-microamp = <100000>;
>> +				regulator-max-microamp = <3150000>;
>> +			};
>> +		};
>> +
>> +		haptic: max77843-haptic {
>> +			compatible = "maxim,max77843-haptic";
>> +			haptic-supply = <&ldo38_reg>;
>> +			pwms = <&pwm 0 33670 0>;
>> +			pwm-names = "haptic";
>> +		};
>> +	};
>> +};
>> +
>> +&hsi2c_11 {
>> +	status = "okay";
> 
> What is inside? How does it work if there is no child device specified?

It is unneeded. I'll remove it.

> 
>> +};
>> +
>> +&i2s0 {
>> +	status = "okay";
>> +};
>> +
>> +&lpass {
>> +	status = "okay";
>> +};
>> +
>> +&mshc_0 {
>> +	status = "okay";
>> +	num-slots = <1>;
>> +	broken-cd;
>> +	non-removable;
> 
> Putting both properties - broken and non-removable - is not supported.
> Please choose one.

I'll remove the 'broken-cd' property.

> 
>> +	card-detect-delay = <200>;
>> +	samsung,dw-mshc-ciu-div = <3>;
>> +	samsung,dw-mshc-sdr-timing = <0 4>;
>> +	samsung,dw-mshc-ddr-timing = <0 2>;
>> +	samsung,dw-mshc-hs400-timing = <0 3>;
>> +	samsung,read-strobe-delay = <90>;
>> +	fifo-depth = <0x80>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_rdqs>;
>> +	bus-width = <8>;
>> +	assigned-clocks = <&cmu_top CLK_SCLK_MMC0_FSYS>;
>> +	assigned-clock-rates = <800000000>;
>> +};
>> +
>> +&pinctrl_alive {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_alive>;
>> +
>> +	initial_alive: initial-state {
>> +		PIN(IN, gpa0-0, DOWN, LV1);
>> +		PIN(IN, gpa0-1, NONE, LV1);
>> +		PIN(IN, gpa0-2, DOWN, LV1);
>> +		PIN(IN, gpa0-3, NONE, LV1);
>> +		PIN(IN, gpa0-4, NONE, LV1);
>> +		PIN(IN, gpa0-5, DOWN, LV1);
>> +		PIN(IN, gpa0-6, NONE, LV1);
>> +		PIN(IN, gpa0-7, NONE, LV1);
>> +
>> +		PIN(IN, gpa1-0, UP, LV1);
>> +		PIN(IN, gpa1-1, NONE, LV1);
>> +		PIN(IN, gpa1-2, NONE, LV1);
>> +		PIN(IN, gpa1-3, DOWN, LV1);
>> +		PIN(IN, gpa1-4, DOWN, LV1);
>> +		PIN(IN, gpa1-5, NONE, LV1);
>> +		PIN(IN, gpa1-6, NONE, LV1);
>> +		PIN(IN, gpa1-7, NONE, LV1);
>> +
>> +		PIN(IN, gpa2-0, NONE, LV1);
>> +		PIN(IN, gpa2-1, NONE, LV1);
>> +		PIN(IN, gpa2-2, NONE, LV1);
>> +		PIN(IN, gpa2-3, DOWN, LV1);
>> +		PIN(IN, gpa2-4, NONE, LV1);
>> +		PIN(IN, gpa2-5, DOWN, LV1);
>> +		PIN(IN, gpa2-6, DOWN, LV1);
>> +		PIN(IN, gpa2-7, NONE, LV1);
>> +
>> +		PIN(IN, gpa3-0, DOWN, LV1);
>> +		PIN(IN, gpa3-1, DOWN, LV1);
>> +		PIN(IN, gpa3-2, NONE, LV1);
>> +		PIN(IN, gpa3-3, DOWN, LV1);
>> +		PIN(IN, gpa3-4, NONE, LV1);
>> +		PIN(IN, gpa3-5, DOWN, LV1);
>> +		PIN(IN, gpa3-6, DOWN, LV1);
>> +		PIN(IN, gpa3-7, DOWN, LV1);
>> +
>> +		PIN(IN, gpf1-0, NONE, LV1);
>> +		PIN(IN, gpf1-1, NONE, LV1);
>> +		PIN(IN, gpf1-2, DOWN, LV1);
>> +		PIN(IN, gpf1-4, UP, LV1);
>> +		PIN(OUT, gpf1-5, NONE, LV1);
>> +		PIN(IN, gpf1-6, DOWN, LV1);
>> +		PIN(IN, gpf1-7, DOWN, LV1);
>> +
>> +		PIN(IN, gpf2-0, DOWN, LV1);
>> +		PIN(IN, gpf2-1, DOWN, LV1);
>> +		PIN(IN, gpf2-2, DOWN, LV1);
>> +		PIN(IN, gpf2-3, DOWN, LV1);
>> +
>> +		PIN(IN, gpf3-0, DOWN, LV1);
>> +		PIN(IN, gpf3-1, DOWN, LV1);
>> +		PIN(IN, gpf3-2, NONE, LV1);
>> +		PIN(IN, gpf3-3, DOWN, LV1);
>> +
>> +		PIN(IN, gpf4-0, DOWN, LV1);
>> +		PIN(IN, gpf4-1, DOWN, LV1);
>> +		PIN(IN, gpf4-2, DOWN, LV1);
>> +		PIN(IN, gpf4-3, DOWN, LV1);
>> +		PIN(IN, gpf4-4, DOWN, LV1);
>> +		PIN(IN, gpf4-5, DOWN, LV1);
>> +		PIN(IN, gpf4-6, DOWN, LV1);
>> +		PIN(IN, gpf4-7, DOWN, LV1);
>> +
>> +		PIN(IN, gpf5-0, DOWN, LV1);
>> +		PIN(IN, gpf5-1, DOWN, LV1);
>> +		PIN(IN, gpf5-2, DOWN, LV1);
>> +		PIN(IN, gpf5-3, DOWN, LV1);
>> +		PIN(OUT, gpf5-4, NONE, LV1);
>> +		PIN(IN, gpf5-5, DOWN, LV1);
>> +		PIN(IN, gpf5-6, DOWN, LV1);
>> +		PIN(IN, gpf5-7, DOWN, LV1);
>> +	};
>> +
>> +	te_irq: te_irq {
>> +		samsung,pins = "gpf1-3";
>> +		samsung,pin-function = <0xf>;
>> +	};
>> +};
>> +
>> +&pinctrl_cpif {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_cpif>;
>> +
>> +	initial_cpif: initial-state {
>> +		PIN(IN, gpv6-0, DOWN, LV1);
>> +		PIN(IN, gpv6-1, DOWN, LV1);
>> +	};
>> +};
>> +
>> +&pinctrl_ese {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_ese>;
>> +
>> +	initial_ese: initial-state {
>> +		PIN(IN, gpj2-0, DOWN, LV1);
>> +		PIN(IN, gpj2-1, DOWN, LV1);
>> +		PIN(IN, gpj2-2, DOWN, LV1);
>> +	};
>> +};
>> +
>> +&pinctrl_fsys {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_fsys>;
>> +
>> +	initial_fsys: initial-state {
>> +		PIN(IN, gpr3-0, NONE, LV1);
>> +		PIN(IN, gpr3-1, DOWN, LV1);
>> +		PIN(IN, gpr3-2, DOWN, LV1);
>> +		PIN(IN, gpr3-3, DOWN, LV1);
>> +		PIN(IN, gpr3-7, NONE, LV1);
>> +	};
>> +};
>> +
>> +&pinctrl_imem {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_imem>;
>> +
>> +	initial_imem: initial-state {
>> +		PIN(IN, gpf0-0, UP, LV1);
>> +		PIN(IN, gpf0-1, UP, LV1);
>> +		PIN(IN, gpf0-2, DOWN, LV1);
>> +		PIN(IN, gpf0-3, UP, LV1);
>> +		PIN(IN, gpf0-4, DOWN, LV1);
>> +		PIN(IN, gpf0-5, NONE, LV1);
>> +		PIN(IN, gpf0-6, DOWN, LV1);
>> +		PIN(IN, gpf0-7, UP, LV1);
>> +	};
>> +};
>> +
>> +&pinctrl_nfc {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_nfc>;
>> +
>> +	initial_nfc: initial-state {
>> +		PIN(IN, gpj0-2, DOWN, LV1);
>> +	};
>> +};
>> +
>> +&pinctrl_peric {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_peric>;
>> +
>> +	initial_peric: initial-state {
>> +		PIN(IN, gpv7-0, DOWN, LV1);
>> +		PIN(IN, gpv7-1, DOWN, LV1);
>> +		PIN(IN, gpv7-2, NONE, LV1);
>> +		PIN(IN, gpv7-3, DOWN, LV1);
>> +		PIN(IN, gpv7-4, DOWN, LV1);
>> +		PIN(IN, gpv7-5, DOWN, LV1);
>> +
>> +		PIN(IN, gpb0-4, DOWN, LV1);
>> +
>> +		PIN(IN, gpc0-2, DOWN, LV1);
>> +		PIN(IN, gpc0-5, DOWN, LV1);
>> +		PIN(IN, gpc0-7, DOWN, LV1);
>> +
>> +		PIN(IN, gpc1-1, DOWN, LV1);
>> +
>> +		PIN(IN, gpc3-4, NONE, LV1);
>> +		PIN(IN, gpc3-5, NONE, LV1);
>> +		PIN(IN, gpc3-6, NONE, LV1);
>> +		PIN(IN, gpc3-7, NONE, LV1);
>> +
>> +		PIN(OUT, gpg0-0, NONE, LV1);
>> +		PIN(FUNC1, gpg0-1, DOWN, LV1);
>> +
>> +		PIN(IN, gpd2-5, DOWN, LV1);
>> +
>> +		PIN(IN, gpd4-0, NONE, LV1);
>> +		PIN(IN, gpd4-1, DOWN, LV1);
>> +		PIN(IN, gpd4-2, DOWN, LV1);
>> +		PIN(IN, gpd4-3, DOWN, LV1);
>> +		PIN(IN, gpd4-4, DOWN, LV1);
>> +
>> +		PIN(IN, gpd6-3, DOWN, LV1);
>> +
>> +		PIN(IN, gpd8-1, UP, LV1);
>> +
>> +		PIN(IN, gpg1-0, DOWN, LV1);
>> +		PIN(IN, gpg1-1, DOWN, LV1);
>> +		PIN(IN, gpg1-2, DOWN, LV1);
>> +		PIN(IN, gpg1-3, DOWN, LV1);
>> +		PIN(IN, gpg1-4, DOWN, LV1);
>> +
>> +		PIN(IN, gpg2-0, DOWN, LV1);
>> +		PIN(IN, gpg2-1, DOWN, LV1);
>> +
>> +		PIN(IN, gpg3-0, DOWN, LV1);
>> +		PIN(IN, gpg3-1, DOWN, LV1);
>> +		PIN(IN, gpg3-5, DOWN, LV1);
>> +		PIN(IN, gpg3-7, DOWN, LV1);
>> +	};
>> +};
>> +
>> +&pinctrl_touch {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&initial_touch>;
>> +
>> +	initial_touch: initial-state {
>> +		PIN(IN, gpj1-2, DOWN, LV1);
>> +	};
>> +};
>> +
>> +&pwm {
>> +	pinctrl-0 = <&pwm0_out>;
>> +	pinctrl-names = "default";
>> +	status = "okay";
>> +};
>> +
>> +&mic {
>> +	status = "okay";
>> +
>> +	i80-if-timings {
>> +	};
>> +};
>> +
>> +&serial_1 {
>> +	status = "okay";
>> +};
>> +
>> +&spi_1 {
>> +	cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
>> +	status = "okay";
>> +
>> +	wm5110: wm5110-codec@0 {
>> +		compatible = "wlf,wm5110";
>> +		reg = <0x0>;
>> +		spi-max-frequency = <20000000>;
>> +		interrupt-parent = <&gpa0>;
>> +		interrupts = <4 0 0>;
> 
> Why three interrupt cells? Please use also IRQ_TYPE_NONE for flags.

Two interrupt cells is correct. I check it[2]
[2] Documentation/devicetree/bindings/mfd/arizona.txt

I'll fix it.

> 
>> +		clocks = <&xxti>, <&s2mps13_osc 2>;
> 
> s/2/S2MPS11_CLK_BT/

OK.

Best Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux