Hi Nicolas, just a note: Here is the link to public Linux repo https://github.com/Xilinx/linux-xlnx Thanks, Michal On 9.8.2016 18:56, Punnaiah Choudary Kalluri wrote: > Hi Nicolas, > > 1588 implementation in cadence GEM IP we have in Zynq Ultascale+ MPSoC is > Different to the one in Zynq SOC. > > In earlier version, all timestamp values will be stored in registers and there is no specific > Mechanism to distinguish the received ethernet frame that contains time stamp information > Other than parsing the frame for PTP packet type. > > We have basic implementation for earlier version in our out of tree driver, which is going to be deprecated > Soon. You could also check the below driver for 1588 support. > https://gitenterprise.xilinx.com/Linux/linux-xlnx/blob/master/drivers/net/ethernet/xilinx/xilinx_emacps.c > > > Regards, > Punnaiah > >> -----Original Message----- >> From: Nicolas Ferre [mailto:nicolas.ferre@xxxxxxxxx] >> Sent: Tuesday, August 09, 2016 10:10 PM >> To: Harini Katakam <harinikatakamlinux@xxxxxxxxx>; Harini Katakam >> <harinik@xxxxxxxxxx>; Andrei Pistirica <Andrei.Pistirica@xxxxxxxxxxxxx> >> Cc: davem@xxxxxxxxxxxxx; Boris Brezillon <boris.brezillon@free- >> electrons.com>; alexandre.belloni@xxxxxxxxxxxxxxxxxx; >> netdev@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; >> devicetree@xxxxxxxxxxxxxxx; Punnaiah Choudary Kalluri >> <punnaia@xxxxxxxxxx>; Michal Simek <michals@xxxxxxxxxx>; Anirudha >> Sarangi <anirudh@xxxxxxxxxx> >> Subject: Re: [RFC PATCH 2/3] net: macb: Add support for 1588 for Zynq >> Ultrascale+ MPSoC >> >> Le 21/09/2015 à 19:49, Harini Katakam a écrit : >>> On Fri, Sep 11, 2015 at 1:27 PM, Harini Katakam >>> <harini.katakam@xxxxxxxxxx> wrote: >>>> Cadence GEM in Zynq Ultrascale+ MPSoC supports 1588 and provides a >>>> 102 bit time counter with 48 bits for seconds, 30 bits for nsecs and >>>> 24 bits for sub-nsecs. The timestamp is made available to the SW through >>>> registers as well as (more precisely) through upper two words in >>>> an extended BD. >>>> >>>> This patch does the following: >>>> - Adds MACB_CAPS_TSU in zynqmp_config. >>>> - Registers to ptp clock framework (after checking for timestamp support >> in >>>> IP and capability in config). >>>> - TX BD and RX BD control registers are written to populate timestamp in >>>> extended BD words. >>>> - Timer initialization is done by writing time of day to the timer counter. >>>> - ns increment register is programmed as NS_PER_SEC/TSU_CLK. >>>> For a 24 bit subns precision, the subns increment equals >>>> remainder of (NS_PER_SEC/TSU_CLK) * (2^24). >>>> TSU (Time stamp unit) clock is obtained by the driver from devicetree. >>>> - HW time stamp capabilities are advertised via ethtool and macb ioctl is >>>> updated accordingly. >>>> - For all PTP event frames, nanoseconds and the lower 5 bits of seconds >> are >>>> obtained from the BD. This offers a precise timestamp. The upper bits >>>> (which dont vary between consecutive packets) are obtained from the >>>> TX/RX PTP event/PEER registers. The timestamp obtained thus is >> updated >>>> in skb for upper layers to access. >>>> - The drivers register functions with ptp to perform time and frequency >>>> adjustment. >>>> - Time adjustment is done by writing to the 1558_ADJUST register. >>>> The controller will read the delta in this register and update the timer >>>> counter register. Alternatively, for large time offset adjustments, >>>> the driver reads the secs and nsecs counter values, adds/subtracts the >>>> delta and updates the timer counter. In order to be as precise as >> possible, >>>> nsecs counter is read again if secs has incremented during the counter >> read. >>>> - Frequency adjustment is not directly supported by this IP. >>>> addend is the initial value ns increment and similarly addendesub. >>>> The ppb (parts per billion) provided is used as >>>> ns_incr = addend +/- (ppb/rate). >>>> Similarly the remainder of the above is used to populate subns >> increment. >>>> In case the ppb requested is negative AND subns adjustment greater >> than >>>> the addendsub, ns_incr is reduced by 1 and subns_incr is adjusted in >>>> positive accordingly. >>>> >>>> Signed-off-by: Harini Katakam <harinik@xxxxxxxxxx>: >>>> --- >>>> drivers/net/ethernet/cadence/macb.c | 372 >> ++++++++++++++++++++++++++++++++++- >>>> drivers/net/ethernet/cadence/macb.h | 64 ++++++ >>>> 2 files changed, 428 insertions(+), 8 deletions(-) >>>> >>>> diff --git a/drivers/net/ethernet/cadence/macb.c >> b/drivers/net/ethernet/cadence/macb.c >>>> index bb2932c..b531008 100644 >>>> --- a/drivers/net/ethernet/cadence/macb.c >>>> +++ b/drivers/net/ethernet/cadence/macb.c >>>> @@ -30,6 +30,8 @@ >>>> #include <linux/of_device.h> >>>> #include <linux/of_mdio.h> >> >> [..] >> >>>> + unsigned int ns_incr; >>>> + unsigned int subns_incr; >>>> }; >>>> >>>> static inline bool macb_is_gem(struct macb *bp) >>>> -- >>>> 1.7.9.5 >>> >>> Ping >>> >>> Thanks. >> >> Harini, >> >> I come back to this patch of last year and I'm sorry about being so late >> answering you. >> >> Andrei who is added to the discussion will have some time to deal with >> this feature and we would like to make some progress with it. He already >> had some work done on his side before I recall your email. >> >> So, could you please re-send your original 1588 patch with Andrei in >> copy so that we can all (re-)start the discussion and progress for >> adding this feature. >> >> We must also note that some hardware differences between our platforms >> may have an impact on the code and how we implement things (as >> highlighted on this forum: >> http://www.at91.com/discussions/viewtopic.php/f,12/t,25462.html). >> Anyway, we'll overcome this and have a widely tested solution at the end >> of the day! >> >> Thanks for your patience, bye! >> >> PS: for some reason, I only have this "ping" part of your email but not >> the original one >> -- >> Nicolas Ferre -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
