Re: [PATCH 3/6] dt/bindings: Add bindings for Tegra GMI controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




2016-08-09 15:34 GMT+02:00 Jon Hunter <jonathanh@xxxxxxxxxx>:
>
> On 09/08/16 09:40, Mirza Krak wrote:
>> 2016-08-08 16:44 GMT+02:00 Jon Hunter <jonathanh@xxxxxxxxxx>:
>>>
>>> On 06/08/16 20:40, Mirza Krak wrote:
>>>> From: Mirza Krak <mirza.krak@xxxxxxxxx>
>>>>

<--snip-->

>>>> + - nvidia,snor-we-width: Number of cycles during which WE stays asserted.
>>>> +   Valid values are 0-15, default is 1
>>>> + - nvidia,snor-oe-width: Number of cycles during which OE stays asserted.
>>>> +   Valid values are 0-255, default is 1
>>>> + - nvidia,snor-wait-width: Number of cycles before READY is asserted.
>>>> +   Valid values are 0-255, default is 3
>>>> +
>>>> +Example with two SJA1000 CAN controllers connected to the GMI bus:
>>>> +
>>>> +  gmi@70090000 {
>>>> +    #address-cells = <1>;
>>>> +    #size-cells = <1>;
>>>
>>> I think 0 for size makes sense. I know that caused you problems before,
>>> but I am wondering if ...
>>>
>>>> +    ranges;
>>>
>>> ... ranges is needed here? If we do have it, I am wondering if it should
>>> be a single entry for the chip-select that is being used. For now we
>>> could only support a ranges with one entry.
>>>
>>>         #address-cells = <1>;
>>>         #size-cells = <1>;
>>>         ranges = <4 0x48000000 0x00040000>;
>>
>> I prefer if we have "ranges" with one single entry, and warn if user enters
>> multiple for now, like we discussed earlier. Should have really done it in
>> this series.
>
> I think I do as well.
>
>>>
>>>> +    nvidia,snor-mux-mode;
>>>> +    nvidia,snor-adv-inv;
>>>> +    nvidia,snor-cs-select = <4>;
>>>
>>> I would have expected these under bus@X node as they are specific to the
>>> GMI CS.
>>
>> Yes, that is true.
>>
>>>
>>> I would also expect that the actual chip-select number is encoded in the
>>> reg property.
>>>
>>>> +
>>>> +    bus@0,0 {
>>>
>>> bus@4
>>
>> ACK.
>>
>>>
>>> No mention of this bus node in the above documentation.
>>
>> I was hesitant documenting it since I am not sure if we really need it
>> in a generic case? It does make sense in my
>> specific case. But what would it look like if we could maintain CS in software.
>>
>> Do you then have a bus node per CS? I am guessing not. Is it enough to
>> document it in my "example brief"?
>
> I see what you mean. May be it is fine to document with the examples
> below how child devices should be populated. You should also state that
> currently the GMI only supports one child device currently for the
> chip-select that is being used.

Should I really need to state that? Is it not always the case, that
you have one child device per chip-select?

Best Regards
Mirza
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux