Hi all, This is a follow-up for my last power sequence framework patch set [1]. According to Rob Herring and Ulf Hansson's comments[2], I use a generic power sequence library for parsing the power sequence elements on DT, and implement generic power sequence on library. The host driver can allocate power sequence instance, and calls pwrseq APIs accordingly. In future, if there are special power sequence requirements, the special power sequence library can be created. This patch set is tested on i.mx6 sabresx evk using a dts change, I use two hot-plug devices to simulate this use case, the related binding change is updated at patch [1/6], The udoo board changes were tested using my last power sequence patch set.[3] Except for hard-wired MMC and USB devices, I find the USB ULPI PHY also need to power on itself before it can be found by ULPI bus. [1] http://www.spinics.net/lists/linux-usb/msg142755.html [2] http://www.spinics.net/lists/linux-usb/msg143106.html [3] http://www.spinics.net/lists/linux-usb/msg142815.html Changes for v5: - Delete pwrseq_register/pwrseq_unregister, which is useless currently - Fix the linker error when the pwrseq user is compiled as module Changes for v4: - Create the patch on next-20160722 - Fix the of_node is not NULL after chipidea driver is unbinded [Patch 5/6] - Using more friendly wait method for reset gpio [Patch 2/6] - Support multiple input clocks [Patch 2/6] - Add Rob Herring's ack for DT changes - Add Joshua Clayton's Tested-by Changes for v3: - Delete "power-sequence" property at binding-doc, and change related code at both library and user code. - Change binding-doc example node name with Rob's comments - of_get_named_gpio_flags only gets the gpio, but without setting gpio flags, add additional code request gpio with proper gpio flags - Add Philipp Zabel's Ack and MAINTAINER's entry Changes for v2: - Delete "pwrseq" prefix and clock-names for properties at dt binding - Should use structure not but its pointer for kzalloc - Since chipidea core has no of_node, let core's of_node equals glue layer's at core's probe Peter Chen (6): binding-doc: power: pwrseq-generic: add binding doc for generic power sequence library power: add power sequence library binding-doc: usb: usb-device: add optional properties for power sequence usb: core: add power sequence handling for USB devices usb: chipidea: let chipidea core device of_node equal's glue layer device of_node ARM: dts: imx6qdl-udoo.dtsi: fix onboard USB HUB property .../bindings/power/pwrseq/pwrseq-generic.txt | 48 ++++++ .../devicetree/bindings/usb/usb-device.txt | 10 +- MAINTAINERS | 9 ++ arch/arm/boot/dts/imx6qdl-udoo.dtsi | 26 ++-- drivers/power/Kconfig | 1 + drivers/power/Makefile | 1 + drivers/power/pwrseq/Kconfig | 20 +++ drivers/power/pwrseq/Makefile | 2 + drivers/power/pwrseq/core.c | 62 ++++++++ drivers/power/pwrseq/pwrseq_generic.c | 168 +++++++++++++++++++++ drivers/usb/chipidea/core.c | 11 ++ drivers/usb/core/Makefile | 1 + drivers/usb/core/hub.c | 12 +- drivers/usb/core/hub.h | 12 ++ drivers/usb/core/pwrseq.c | 100 ++++++++++++ include/linux/power/pwrseq.h | 47 ++++++ 16 files changed, 513 insertions(+), 17 deletions(-) create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt create mode 100644 drivers/power/pwrseq/Kconfig create mode 100644 drivers/power/pwrseq/Makefile create mode 100644 drivers/power/pwrseq/core.c create mode 100644 drivers/power/pwrseq/pwrseq_generic.c create mode 100644 drivers/usb/core/pwrseq.c create mode 100644 include/linux/power/pwrseq.h -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
