From: Mark Rutland [mailto:mark.rutland@xxxxxxx] Data: Tuesday, November 26, 2013 10:09 PM >To: Duan Fugang-B38611 >Cc: jic23@xxxxxxxxxx; sachin.kamat@xxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; >shawn.guo@xxxxxxxxxx; Li Frank-B20596; linux-iio@xxxxxxxxxxxxxxx >Subject: Re: [PATCH v3 3/3] Documentation: add the binding file for Freescale >vf610 ADC driver > >On Tue, Nov 26, 2013 at 10:56:34AM +0000, Fugang Duan wrote: >> The patch adds the binding file for Freescale vf610 ADC driver. >> >> Signed-off-by: Fugang Duan <B38611@xxxxxxxxxxxxx> >> --- >> .../devicetree/bindings/iio/adc/vf610-adc.txt | 57 >++++++++++++++++++++ >> 1 files changed, 57 insertions(+), 0 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt >> b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt >> new file mode 100644 >> index 0000000..4101516 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt >> @@ -0,0 +1,57 @@ >> +Freescale vf610 Analog to Digital Converter bindings >> + >> +The devicetree bindings are for the new ADC driver written for >> +vf610/i.MX6slx and upward SoCs from Freescale. >> + >> +Required properties: >> +- compatible: Should be "fsl,vf610-adc" > >s/be/contain/ > >> +- reg: Offset and length of the register set for the device >> +- interrupts: Should contain the interrupt for the device >> +- clocks: The clocks needed by the ADC controller > >How many? Which ones? > >> +- clock-names: the name of the clocks > >Either define the set of names, or don't use clock-names. It's useless if it >doesn't tell you anything. > >> + >> +Optional properties: >> +- fsl,adc-io-pinctl: Enable field for the I/O port control of MCU pins used >as analog inputs. >> +- fsl,adc-vref: ADC refrence voltage value, unit is uV. > >Can you not query the regulator to figure this out? This is optional, some board design have no fixed regulator, just supply fixed voltage from MCU digital power which Cannot handled by the module. > >> +- fsl,adc-clk-div: Current clock divider value, such as 1,2,4,8,16 and so on. > >Could you elaborate on this? What's it used for and why is it needed? Exp: ADC clock source is ipg bus clock, the clk divider can control the ADC sample speed while other setting don't change: The sample speed that clock divider is equal to 1 is twice than the divider is equal to 2. Anyway, it can control sample speed by user. > >> +- fsl,adc-res: ADC conversion mode selection, such as 8 for 8-bit, 10 for >10-bit, 12 for 12-bit mode. > >This sounds like something that could be changed at runtime. Why does this need >to be configured in the DT? > >> +- fsl,adc-sam-time: ADC sample time duration, number of ADC clocks, >> +such as 2, 4, 6, 8, 12, 16, 20, 24 > >Likewise. > >Please don't poinltessly abbreviate, "sample" is much better than "sam" >here... > >> +- fsl,adc-aver-sam-sel: Determines how many ADC conversions will be averaged >to create the ADC average result. >> + The Optional value is 4, 8, 16, 32. > >Likewise. For above ADC configuration, ADC conversion mode, sample time duration, hardware average sample selection, and so on. All of them can changed at runtime. The only method is to introduce the ioctl interface for user to change them at runtime. How about you think ? > >> +- fsl,adc-hw-aver-en: Bool type to decide enable hardware average function. > >When would you wnat this and when wouldn't you? > >Similarly, "averages" is far clearer than "aver". Ok, I see. Thanks. > >> +- fsl,adc-low-power-mode: Bool type to decide enable ADC low power mode. > >Similarly? > >> +- fsl,adc-high-speed-conv: Bool type to decide enable ADC high speed mode. > >Similarly? > >> +- vref: The regulator to support ADC refrence voltage. > >s/vref/vref-supply/ > >Thanks, >Mark. Thanks for your review. Summary, there have many comments why don't let some ADC configuration change at runtime. The driver still don't add ioctl interface for user to configurate the ADC setting. So the setting are got from DT. Do you have one good method to change the configuration at runtime ? Thanks, Andy -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
