Re: [PATCH] bindings: PCI: artpec: correct pci binding example

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 07/08/2016 11:39 AM, Arnd Bergmann wrote:
> On Friday, July 8, 2016 1:28:10 AM CEST Niklas Cassel wrote:
>> From: Niklas Cassel <niklas.cassel@xxxxxxxx>
>>
>>  - Increase config size. When using a PCIe switch,
>>    the previous config size only had room for one device.
>>  - Add bus range. Inherited optional property.
>>  - Map downstream I/O to PCI address 0. We can map it to any
>>    address, but let's be consistent with other drivers.
>>
>> Signed-off-by: Niklas Cassel <niklas.cassel@xxxxxxxx>
>> ---
>>  Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt | 7 ++++---
>>  1 file changed, 4 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
>> index 330a45b..5ecaea1 100644
>> --- a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
>> +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
>> @@ -24,16 +24,17 @@ Example:
>>  		compatible = "axis,artpec6-pcie", "snps,dw-pcie";
>>  		reg = <0xf8050000 0x2000
>>  		       0xf8040000 0x1000
>> -		       0xc0000000 0x1000>;
>> +		       0xc0000000 0x2000>;
> If this is your config space size
>
>>  		num-lanes = <2>;
>> +		bus-range = <0x00 0xff>;
> then the bus range looks too large. These two are typically connected.
> I couldn't immediately see which config space access function is
> used, but if you have 0x1000 bytes per bus, then the bus range matching
> a 0x2000 byte config space would be either <0x00 0x01> or <0x00 0x02>
> depending whether the root bus is part of that range.

I see your point, a config space size of 0x2000 is only enough to
hold two configuration space headers.

However, all other PCIe controllers based on Synopsys DesignWare IP
with a config space size of 0x2000, uses a bus-range of 0x0-0xff.
(Except hisilicon which for some reason uses 0x0-0xf).
Isn't it better to be consistent with the other DesignWare based controllers?

Also, isn't is possible to have a device behind bus 1, then nothing behind
bus 2, and then a device behind bus 3?
Not sure if this could actually happen though, since Linux appears to assign
the bus numbers, unless already defined by BIOS.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux