The dts file uses "bananapi" for some labels and "bananapim1plus" for other. Use the shortened "bpi_m1p" suffix for all board specific labels. Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx> --- arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts index edfb5b37939e..14fb463758e4 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts @@ -63,7 +63,7 @@ leds { compatible = "gpio-leds"; pinctrl-names = "default"; - pinctrl-0 = <&led_pins_bananapi>; + pinctrl-0 = <&led_pins_bpi_m1p>; green { label = "bananapi-m1-plus:green:usr"; @@ -81,14 +81,14 @@ mmc3_pwrseq: mmc3_pwrseq { compatible = "mmc-pwrseq-simple"; pinctrl-names = "default"; - pinctrl-0 = <&mmc3_pwrseq_pin_bananapim1plus>; + pinctrl-0 = <&mmc3_pwrseq_pin_bpi_m1p>; reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */ }; reg_gmac_3v3: gmac-3v3 { compatible = "regulator-fixed"; pinctrl-names = "default"; - pinctrl-0 = <&gmac_power_pin_bananapi>; + pinctrl-0 = <&gmac_power_pin_bpi_m1p>; regulator-name = "gmac-3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -151,7 +151,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m1p>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ @@ -194,28 +194,28 @@ }; &pio { - gmac_power_pin_bananapi: gmac_power_pin@0 { + gmac_power_pin_bpi_m1p: gmac_power_pin@0 { allwinner,pins = "PH23"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; - led_pins_bananapi: led_pins@0 { + led_pins_bpi_m1p: led_pins@0 { allwinner,pins = "PH24", "PG2"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; - mmc0_cd_pin_bananapi: mmc0_cd_pin@0 { + mmc0_cd_pin_bpi_m1p: mmc0_cd_pin@0 { allwinner,pins = "PH10"; allwinner,function = "gpio_in"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; - mmc3_pwrseq_pin_bananapim1plus: mmc3_pwrseq_pin@0 { + mmc3_pwrseq_pin_bpi_m1p: mmc3_pwrseq_pin@0 { allwinner,pins = "PH22"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; -- 2.8.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html