Add the interrupts cells value for 4, and the 4th cell is zero.
Due to the doc[0] said:" the system requires describing PPI affinity,
then the value must be at least 4"
The 4th cell is a phandle to a node describing a set of CPUs this
interrupt is affine to. The interrupt must be a PPI, and the node
pointed must be a subnode of the "ppi-partitions" subnode. For
interrupt types other than PPI or PPIs that are not partitionned,
this cell must be zero. See the "ppi-partitions" node description
below.
[0]:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Caesar Wang <wxt@xxxxxxxxxxxxxx>
Cc: Heiko Stuebner <heiko@xxxxxxxxx>
Cc: Will Deacon <will.deacon@xxxxxxx>
Cc: Marc Zyngier <marc.zyngier@xxxxxxx>
CC: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
---
arch/arm64/boot/dts/rockchip/rk3399.dtsi | 98 ++++++++++++++++----------------
1 file changed, 49 insertions(+), 49 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index a6dd623..8f0a069 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -159,10 +159,10 @@
timer {
compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
};
xin24m: xin24m {
@@ -181,8 +181,8 @@
dmac_bus: dma-controller@ff6d0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x0 0xff6d0000 0x0 0x4000>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <1>;
clocks = <&cru ACLK_DMAC0_PERILP>;
clock-names = "apb_pclk";
@@ -191,8 +191,8 @@
dmac_peri: dma-controller@ff6e0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x0 0xff6e0000 0x0 0x4000>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <1>;
clocks = <&cru ACLK_DMAC1_PERILP>;
clock-names = "apb_pclk";
@@ -203,7 +203,7 @@
compatible = "rockchip,rk3399-dw-mshc",
"rockchip,rk3288-dw-mshc";
reg = <0x0 0xfe310000 0x0 0x4000>;
- interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH 0>;
clock-freq-min-max = <400000 150000000>;
clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
<&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
@@ -216,7 +216,7 @@
compatible = "rockchip,rk3399-dw-mshc",
"rockchip,rk3288-dw-mshc";
reg = <0x0 0xfe320000 0x0 0x4000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH 0>;
clock-freq-min-max = <400000 150000000>;
clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
<&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
@@ -228,7 +228,7 @@
sdhci: sdhci@fe330000 {
compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1";
reg = <0x0 0xfe330000 0x0 0x10000>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH 0>;
arasan,soc-ctl-syscon = <&grf>;
assigned-clocks = <&cru SCLK_EMMC>;
assigned-clock-rates = <200000000>;
@@ -244,7 +244,7 @@
usb_host0_ehci: usb@fe380000 {
compatible = "generic-ehci";
reg = <0x0 0xfe380000 0x0 0x20000>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
clock-names = "hclk_host0", "hclk_host0_arb";
status = "disabled";
@@ -253,7 +253,7 @@
usb_host0_ohci: usb@fe3a0000 {
compatible = "generic-ohci";
reg = <0x0 0xfe3a0000 0x0 0x20000>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
clock-names = "hclk_host0", "hclk_host0_arb";
status = "disabled";
@@ -262,7 +262,7 @@
usb_host1_ehci: usb@fe3c0000 {
compatible = "generic-ehci";
reg = <0x0 0xfe3c0000 0x0 0x20000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
clock-names = "hclk_host1", "hclk_host1_arb";
status = "disabled";
@@ -271,7 +271,7 @@
usb_host1_ohci: usb@fe3e0000 {
compatible = "generic-ohci";
reg = <0x0 0xfe3e0000 0x0 0x20000>;
- interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
clock-names = "hclk_host1", "hclk_host1_arb";
status = "disabled";
@@ -279,7 +279,7 @@
gic: interrupt-controller@fee00000 {
compatible = "arm,gic-v3";
- #interrupt-cells = <3>;
+ #interrupt-cells = <4>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
@@ -290,7 +290,7 @@
<0x0 0xfff00000 0 0x10000>, /* GICC */
<0x0 0xfff10000 0 0x10000>, /* GICH */
<0x0 0xfff20000 0 0x10000>; /* GICV */
- interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
its: interrupt-controller@fee20000 {
compatible = "arm,gic-v3-its";
msi-controller;
@@ -305,7 +305,7 @@
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_xfer>;
#address-cells = <1>;
@@ -320,7 +320,7 @@
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_xfer>;
#address-cells = <1>;
@@ -335,7 +335,7 @@
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c3_xfer>;
#address-cells = <1>;
@@ -350,7 +350,7 @@
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C5>, <&cru PCLK_I2C5>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c5_xfer>;
#address-cells = <1>;
@@ -365,7 +365,7 @@
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C6>, <&cru PCLK_I2C6>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c6_xfer>;
#address-cells = <1>;
@@ -380,7 +380,7 @@
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C7>, <&cru PCLK_I2C7>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c7_xfer>;
#address-cells = <1>;
@@ -393,7 +393,7 @@
reg = <0x0 0xff180000 0x0 0x100>;
clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
@@ -406,7 +406,7 @@
reg = <0x0 0xff190000 0x0 0x100>;
clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
@@ -419,7 +419,7 @@
reg = <0x0 0xff1a0000 0x0 0x100>;
clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
@@ -432,7 +432,7 @@
reg = <0x0 0xff1b0000 0x0 0x100>;
clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
@@ -445,7 +445,7 @@
reg = <0x0 0xff1c0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>;
#address-cells = <1>;
@@ -458,7 +458,7 @@
reg = <0x0 0xff1d0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>;
#address-cells = <1>;
@@ -471,7 +471,7 @@
reg = <0x0 0xff1e0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>;
#address-cells = <1>;
@@ -484,7 +484,7 @@
reg = <0x0 0xff1f0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI4>, <&cru PCLK_SPI4>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi4_clk &spi4_tx &spi4_rx &spi4_cs0>;
#address-cells = <1>;
@@ -497,7 +497,7 @@
reg = <0x0 0xff200000 0x0 0x1000>;
clocks = <&cru SCLK_SPI5>, <&cru PCLK_SPI5>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi5_clk &spi5_tx &spi5_rx &spi5_cs0>;
#address-cells = <1>;
@@ -577,7 +577,7 @@
tsadc: tsadc@ff260000 {
compatible = "rockchip,rk3399-tsadc";
reg = <0x0 0xff260000 0x0 0x100>;
- interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH 0>;
assigned-clocks = <&cru SCLK_TSADC>;
assigned-clock-rates = <750000>;
clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
@@ -611,7 +611,7 @@
reg = <0x0 0xff350000 0x0 0x1000>;
clocks = <&pmucru SCLK_SPI3_PMU>, <&pmucru PCLK_SPI3_PMU>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi3_clk &spi3_tx &spi3_rx &spi3_cs0>;
#address-cells = <1>;
@@ -624,7 +624,7 @@
reg = <0x0 0xff370000 0x0 0x100>;
clocks = <&pmucru SCLK_UART4_PMU>, <&pmucru PCLK_UART4_PMU>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
@@ -639,7 +639,7 @@
assigned-clock-rates = <200000000>;
clocks = <&pmucru SCLK_I2C0_PMU>, <&pmucru PCLK_I2C0_PMU>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_xfer>;
#address-cells = <1>;
@@ -654,7 +654,7 @@
assigned-clock-rates = <200000000>;
clocks = <&pmucru SCLK_I2C4_PMU>, <&pmucru PCLK_I2C4_PMU>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c4_xfer>;
#address-cells = <1>;
@@ -669,7 +669,7 @@
assigned-clock-rates = <200000000>;
clocks = <&pmucru SCLK_I2C8_PMU>, <&pmucru PCLK_I2C8_PMU>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c8_xfer>;
#address-cells = <1>;
@@ -778,13 +778,13 @@
compatible = "snps,dw-wdt";
reg = <0x0 0xff840000 0x0 0x100>;
clocks = <&cru PCLK_WDT>;
- interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH 0>;
};
rktimer: rktimer@ff850000 {
compatible = "rockchip,rk3399-timer";
reg = <0x0 0xff850000 0x0 0x1000>;
- interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER00>;
clock-names = "pclk", "timer";
};
@@ -792,7 +792,7 @@
spdif: spdif@ff870000 {
compatible = "rockchip,rk3399-spdif";
reg = <0x0 0xff870000 0x0 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 7>;
dma-names = "tx";
clock-names = "mclk", "hclk";
@@ -806,7 +806,7 @@
compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s";
reg = <0x0 0xff880000 0x0 0x1000>;
rockchip,grf = <&grf>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 0>, <&dmac_bus 1>;
dma-names = "tx", "rx";
clock-names = "i2s_clk", "i2s_hclk";
@@ -819,7 +819,7 @@
i2s1: i2s@ff890000 {
compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s";
reg = <0x0 0xff890000 0x0 0x1000>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 2>, <&dmac_bus 3>;
dma-names = "tx", "rx";
clock-names = "i2s_clk", "i2s_hclk";
@@ -832,7 +832,7 @@
i2s2: i2s@ff8a0000 {
compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s";
reg = <0x0 0xff8a0000 0x0 0x1000>;
- interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 4>, <&dmac_bus 5>;
dma-names = "tx", "rx";
clock-names = "i2s_clk", "i2s_hclk";
@@ -852,7 +852,7 @@
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff720000 0x0 0x100>;
clocks = <&pmucru PCLK_GPIO0_PMU>;
- interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
@@ -865,7 +865,7 @@
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff730000 0x0 0x100>;
clocks = <&pmucru PCLK_GPIO1_PMU>;
- interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
@@ -878,7 +878,7 @@
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff780000 0x0 0x100>;
clocks = <&cru PCLK_GPIO2>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
@@ -891,7 +891,7 @@
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff788000 0x0 0x100>;
clocks = <&cru PCLK_GPIO3>;
- interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
@@ -904,7 +904,7 @@
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff790000 0x0 0x100>;
clocks = <&cru PCLK_GPIO4>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
