This is an alternative SH7751 PCI driver.
Existing driver (arch/sh/drivers/pci/pci-sh7751) uses SH specific interface.
But this driver uses common PCI interface. It is more modern and generic.
Changes v4
Add reg description.
Signed-off-by: Yoshinori Sato <ysato@xxxxxxxxxxxxxxxxxxxx>
---
.../devicetree/bindings/pci/sh7751-pci.txt | 37 +++
arch/sh/boards/Kconfig | 1 +
arch/sh/drivers/Makefile | 2 +
arch/sh/include/asm/io.h | 6 +
drivers/pci/host/Kconfig | 7 +
drivers/pci/host/Makefile | 1 +
drivers/pci/host/pci-sh7751.c | 326 +++++++++++++++++++++
7 files changed, 380 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/sh7751-pci.txt
create mode 100644 drivers/pci/host/pci-sh7751.c
diff --git a/Documentation/devicetree/bindings/pci/sh7751-pci.txt b/Documentation/devicetree/bindings/pci/sh7751-pci.txt
new file mode 100644
index 0000000..2df9af6
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/sh7751-pci.txt
@@ -0,0 +1,37 @@
+* Renesas SH7751 PCI host interfaces
+
+Required properties:
+ - compatible: "renesas,sh7751-pci" is required.
+ And board specific compatible if fixup required.
+ - reg: contain two entries.
+ first entry: PCI controller register base address and length.
+ second entry: BUS controller register base address and length.
+ - #address-cells: set to <2>
+ - #size-cells: set to <1>
+ - bus-range: PCI bus numbers covered
+ - device_type: set to "pci"
+ - ranges: ranges for the PCI memory and I/O regions.
+ - interrupt-map-mask and interrupt-map: standard PCI properties
+ to define the mapping of the PCI interface to interrupt
+ numbers.
+
+Example:
+ pci: pci-controller@fe200000 {
+ compatible = "renesas,sh7751-pci", "iodata,landisk";
+ device_type = "pci";
+ bus-range = <0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0x02000000 0x00000000 0xfd000000 0xfd000000 0x00000000 0x01000000>,
+ <0x01000000 0x00000000 0xfe240000 0x00000000 0x00000000 0x00040000>;
+ reg = <0xfe200000 0x0400>,
+ <0xff800000 0x0030>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0x1800 0 7>;
+ interrupt-map = <0x0000 0 1 &cpldintc 0 0>,
+ 0x0800 0 1 &cpldintc 1 0>,
+ 0x1000 0 1 &cpldintc 2 0>,
+ 0x1800 0 1 &cpldintc 3 0>,
+ 0x1800 0 2 &cpldintc 0 0>;
+ };
+};
diff --git a/arch/sh/boards/Kconfig b/arch/sh/boards/Kconfig
index b6ff9df..cfde921 100644
--- a/arch/sh/boards/Kconfig
+++ b/arch/sh/boards/Kconfig
@@ -14,6 +14,7 @@ config SH_DEVICE_TREE
select GENERIC_CALIBRATE_DELAY
select GENERIC_IOMAP
select COMMON_CLK
+ select SYS_SUPPORTS_PCI
help
Select Board Described by Device Tree to build a kernel that
does not hard-code any board-specific knowledge but instead uses
diff --git a/arch/sh/drivers/Makefile b/arch/sh/drivers/Makefile
index e13f06b..382e86f 100644
--- a/arch/sh/drivers/Makefile
+++ b/arch/sh/drivers/Makefile
@@ -4,7 +4,9 @@
obj-y += dma/
+ifndef CONFIG_SH_DEVICE_TREE
obj-$(CONFIG_PCI) += pci/
+endif
obj-$(CONFIG_SUPERHYWAY) += superhyway/
obj-$(CONFIG_PUSH_SWITCH) += push-switch.o
obj-$(CONFIG_HEARTBEAT) += heartbeat.o
diff --git a/arch/sh/include/asm/io.h b/arch/sh/include/asm/io.h
index 3280a6b..df62a9f 100644
--- a/arch/sh/include/asm/io.h
+++ b/arch/sh/include/asm/io.h
@@ -387,6 +387,12 @@ static inline int iounmap_fixed(void __iomem *addr) { return -EINVAL; }
int valid_phys_addr_range(phys_addr_t addr, size_t size);
int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
+#define PCI_IOBASE 0xfe240000UL
+
+#define HAVE_ARCH_PIO_SIZE
+#define PIO_OFFSET PCI_IOBASE
+#define PIO_MASK 0x3ffffUL
+#define PIO_RESERVED 0x40000UL
#endif /* __KERNEL__ */
#endif /* __ASM_SH_IO_H */
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 5d2374e..df60505 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -245,4 +245,11 @@ config PCIE_ARMADA_8K
Designware hardware and therefore the driver re-uses the
Designware core functions to implement the driver.
+config PCI_SH7751
+ bool "Renesas SH7751 On-Chip PCI controller"
+ depends on OF && SUPERH
+ select PCI_HOST_COMMON
+ help
+ Say Y here if you want PCI support on SH7751.
+
endmenu
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index 9c8698e..4681e49 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -29,3 +29,4 @@ obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
obj-$(CONFIG_PCI_HOST_THUNDER_ECAM) += pci-thunder-ecam.o
obj-$(CONFIG_PCI_HOST_THUNDER_PEM) += pci-thunder-pem.o
obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
+obj-$(CONFIG_PCI_SH7751) += pci-sh7751.o
diff --git a/drivers/pci/host/pci-sh7751.c b/drivers/pci/host/pci-sh7751.c
new file mode 100644
index 0000000..d851fcf3
--- /dev/null
+++ b/drivers/pci/host/pci-sh7751.c
@@ -0,0 +1,326 @@
+/*
+ * SH7751 PCI driver
+ * Copyright (C) 2016 Yoshinori Sato
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include "../ecam.h"
+
+#define SH7751_PCICONF1 0x4 /* PCI Config Reg 1 */
+#define SH7751_PCICONF4 0x10 /* PCI Config Reg 4 */
+#define SH7751_PCICONF5 0x14 /* PCI Config Reg 5 */
+#define SH7751_PCICONF6 0x18 /* PCI Config Reg 6 */
+#define SH4_PCICR 0x100 /* PCI Control Register */
+ #define SH4_PCICR_PREFIX 0xA5000000 /* CR prefix for write */
+ #define SH4_PCICR_FTO BIT(10) /* TRDY/IRDY Enable */
+ #define SH4_PCICR_TRSB BIT(9) /* Target Read Single */
+ #define SH4_PCICR_BSWP BIT(8) /* Target Byte Swap */
+ #define SH4_PCICR_PLUP BIT(7) /* Enable PCI Pullup */
+ #define SH4_PCICR_ARBM BIT(6) /* PCI Arbitration Mode */
+#define SH4_PCICR_MD (BIT(4) | BIT(5)) /* MD9 and MD10 status */
+ #define SH4_PCICR_SERR BIT(3) /* SERR output assert */
+ #define SH4_PCICR_INTA BIT(2) /* INTA output assert */
+ #define SH4_PCICR_PRST BIT(1) /* PCI Reset Assert */
+ #define SH4_PCICR_CFIN BIT(0) /* Central Fun. Init Done */
+#define SH4_PCILSR0 0x104 /* PCI Local Space Register0 */
+#define SH4_PCILSR1 0x108 /* PCI Local Space Register1 */
+#define SH4_PCILAR0 0x10C /* PCI Local Addr Register1 */
+#define SH4_PCILAR1 0x110 /* PCI Local Addr Register1 */
+#define SH4_PCIINTM 0x118 /* PCI Interrupt Mask */
+ #define SH4_PCIINTM_TTADIM BIT(14) /* Target-target abort interrupt */
+ #define SH4_PCIINTM_TMTOIM BIT(9) /* Target retry timeout */
+ #define SH4_PCIINTM_MDEIM BIT(8) /* Master function disable error */
+ #define SH4_PCIINTM_APEDIM BIT(7) /* Address parity error detection */
+ #define SH4_PCIINTM_SDIM BIT(6) /* SERR detection */
+ #define SH4_PCIINTM_DPEITWM BIT(5) /* Data parity error for target write */
+ #define SH4_PCIINTM_PEDITRM BIT(4) /* PERR detection for target read */
+ #define SH4_PCIINTM_TADIMM BIT(3) /* Target abort for master */
+ #define SH4_PCIINTM_MADIMM BIT(2) /* Master abort for master */
+ #define SH4_PCIINTM_MWPDIM BIT(1) /* Master write data parity error */
+ #define SH4_PCIINTM_MRDPEIM BIT(0) /* Master read data parity error */
+#define SH4_PCIAINTM 0x134 /* Arbiter Int. Mask Register */
+#define SH4_PCIPAR 0x1C0 /* PIO Address Register */
+ #define SH4_PCIPAR_CFGEN 0x80000000 /* Configuration Enable */
+ #define SH4_PCIPAR_BUSNO 0x00FF0000 /* Config. Bus Number */
+ #define SH4_PCIPAR_DEVNO 0x0000FF00 /* Config. Device Number */
+ #define SH4_PCIPAR_REGAD 0x000000FC /* Register Address Number */
+#define SH4_PCIPINT 0x1CC /* Power Mgmnt Int. Register */
+ #define SH4_PCIPINT_D3 0x00000002 /* D3 Pwr Mgmt. Interrupt */
+ #define SH4_PCIPINT_D0 0x00000001 /* D0 Pwr Mgmt. Interrupt */
+#define SH4_PCICLKR 0x1D4 /* Clock Ctrl. Register */
+/* For definitions of BCR, MCR see ... */
+#define SH4_PCIBCR1 0x1E0 /* Memory BCR1 Register */
+ #define SH4_PCIMBR0 SH4_PCIBCR1
+#define SH4_PCIBCR2 0x1E4 /* Memory BCR2 Register */
+ #define SH4_PCIMBMR0 SH4_PCIBCR2
+#define SH4_PCIWCR1 0x1E8 /* Wait Control 1 Register */
+#define SH4_PCIWCR2 0x1EC /* Wait Control 2 Register */
+#define SH4_PCIWCR3 0x1F0 /* Wait Control 3 Register */
+ #define SH4_PCIMBR2 SH4_PCIWCR3
+#define SH4_PCIMCR 0x1F4 /* Memory Control Register */
+#define SH4_PCIPDR 0x220 /* Port IO Data Register */
+
+/* Platform Specific Values */
+#define SH7751_VENDOR_ID 0x1054
+#define SH7751_DEVICE_ID 0x3505
+#define SH7751R_DEVICE_ID 0x350e
+
+/* Memory Control Registers */
+#define SH7751_BCR1 0x0000 /* Memory BCR1 Register */
+#define SH7751_BCR2 0x0004 /* Memory BCR2 Register */
+#define SH7751_BCR3 0x0050 /* Memory BCR3 Register */
+#define SH7751_WCR1 0x0008 /* Wait Control 1 Register */
+#define SH7751_WCR2 0x000C /* Wait Control 2 Register */
+#define SH7751_WCR3 0x0010 /* Wait Control 3 Register */
+#define SH7751_MCR 0x0014 /* Memory Control Register */
+
+#define pcic_writel(val, reg) iowrite32(val, pci_reg_base + (reg))
+#define pcic_readl(reg) ioread32(pci_reg_base + (reg))
+
+/*
+ * PCIC fixups
+ */
+
+#define PCIMCR_MRSET 0x40000000
+#define PCIMCR_RFSH 0x00000004
+
+static void __init landisk_fixup(void __iomem *pci_reg_base, void __iomem *bcr)
+{
+ unsigned long bcr1, mcr;
+
+ bcr1 = ioread32(bcr + SH7751_BCR1);
+ bcr1 |= 0x00080000; /* Enable Bit 19 BREQEN, set PCIC to slave */
+ pcic_writel(bcr1, SH4_PCIBCR1);
+
+ mcr = ioread32(bcr + SH7751_MCR);
+ mcr &= (~PCIMCR_MRSET) & (~PCIMCR_RFSH);
+ pcic_writel(mcr, SH4_PCIMCR);
+
+ pcic_writel(0x0c000000, PCI_BASE_ADDRESS_1);
+ pcic_writel(0xd0000000, PCI_BASE_ADDRESS_2);
+ pcic_writel(0x0c000000, SH4_PCILAR0);
+ pcic_writel(0x00000000, SH4_PCILAR1);
+}
+
+static void __init r2dplus_fixup(void __iomem *pci_reg_base, void __iomem *bcr)
+{
+ unsigned long bcr1, mcr;
+
+ bcr1 = ioread32(bcr + SH7751_BCR1);
+ bcr1 |= 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */
+ pcic_writel(bcr1, SH4_PCIBCR1);
+
+ /* Enable all interrupts, so we known what to fix */
+ pcic_writel(0x0000c3ff, SH4_PCIINTM);
+ pcic_writel(0x0000380f, SH4_PCIAINTM);
+
+ pcic_writel(0xfb900047, SH7751_PCICONF1);
+ pcic_writel(0xab000001, SH7751_PCICONF4);
+
+ mcr = ioread32(bcr + SH7751_MCR);
+ mcr &= (~PCIMCR_MRSET) & (~PCIMCR_RFSH);
+ pcic_writel(mcr, SH4_PCIMCR);
+
+ pcic_writel(0x0c000000, SH7751_PCICONF5);
+ pcic_writel(0xd0000000, SH7751_PCICONF6);
+ pcic_writel(0x0c000000, SH4_PCILAR0);
+ pcic_writel(0x00000000, SH4_PCILAR1);
+}
+
+/*
+ * Direct access to PCI hardware...
+ */
+#define CONFIG_CMD(bus, devfn, where) \
+ (0x80000000 | (bus->number << 16) | (devfn << 8) | (where & ~3))
+
+/*
+ * Functions for accessing PCI configuration space with type 1 accesses
+ */
+static void __iomem *sh7751_map_bus(struct pci_bus *bus,
+ unsigned int devfn, int where)
+{
+ struct pci_config_window *cfg = bus->sysdata;
+ void __iomem *pci_reg_base = (void __iomem *)cfg->res.start;
+
+ pcic_writel(CONFIG_CMD(bus, devfn, where), SH4_PCIPAR);
+ return pci_reg_base + SH4_PCIPDR;
+}
+
+static const struct of_device_id fixup_of_match[] = {
+ { .compatible = "iodata,landisk-pci", .data = landisk_fixup, },
+ { .compatible = "renesas,r2dplus-pci", .data = r2dplus_fixup, },
+ { },
+};
+
+static const struct of_device_id sh7751_pci_of_match[] = {
+ { .compatible = "renesas,sh7751-pci", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, sh7751_pci_of_match);
+
+static resource_size_t sh7751_align_resource(struct pci_dev *dev,
+ const struct resource *res,
+ resource_size_t start,
+ resource_size_t size,
+ resource_size_t align)
+{
+ if (res->flags & IORESOURCE_IO) {
+ if (start < PCIBIOS_MIN_IO + 0x1000)
+ start = PCIBIOS_MIN_IO + 0x1000;
+
+ /*
+ * Put everything into 0x00-0xff region modulo 0x400.
+ */
+ if (start & 0x300)
+ start = (start + 0x3ff) & ~0x3ff;
+ }
+
+ return start;
+}
+
+static void __init set_pci_bcr(void __iomem *pci_reg_base,
+ void __iomem *bcr,
+ unsigned int area)
+{
+ unsigned long word;
+
+ word = ioread32(bcr + SH7751_BCR1);
+ /* check BCR for SDRAM in area */
+ if (((word >> area) & 1) == 0) {
+ pr_info("PCI: Area %d is not configured for SDRAM. BCR1=0x%lx\n",
+ area, word);
+ return;
+ }
+ pcic_writel(word, SH4_PCIBCR1);
+
+ word = ioread16(bcr + SH7751_BCR2);
+ /* check BCR2 for 32bit SDRAM interface*/
+ if (((word >> (area << 1)) & 0x3) != 0x3) {
+ pr_info("PCI: Area %d is not 32 bit SDRAM. BCR2=0x%lx\n",
+ area, word);
+ return;
+ }
+ pcic_writel(word, SH4_PCIBCR2);
+}
+
+static __init int sh7751_cfg_init(struct device *dev,
+ struct pci_config_window *cfg)
+{
+ cfg->priv = sh7751_align_resource;
+ return 0;
+}
+
+static struct pci_ecam_ops ecm_ops __initdata = {
+ .init = sh7751_cfg_init,
+ .pci_ops = {
+ .read = pci_generic_config_read32,
+ .write = pci_generic_config_write32,
+ .map_bus = sh7751_map_bus,
+ }
+};
+
+static __init int sh7751_pci_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ u32 id;
+ u32 reg, word;
+ void __iomem *pci_reg_base;
+ void __iomem *bcr;
+ const struct of_device_id *match;
+ void (*fixup_fn)(void __iomem *pci_reg_base, void __iomem *bcr);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pci_reg_base = ioremap(res->start, resource_size(res));
+ if (IS_ERR(pci_reg_base))
+ return PTR_ERR(pci_reg_base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ bcr = ioremap(res->start, resource_size(res));
+ if (IS_ERR(bcr))
+ return PTR_ERR(bcr);
+
+ /* check for SH7751/SH7751R hardware */
+ id = pcic_readl(PCI_VENDOR_ID);
+ if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) &&
+ id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) {
+ pr_warn("PCI: This is not an SH7751(R)\n");
+ return -ENODEV;
+ }
+ dev_info(&pdev->dev, "PCI core found at %pR\n",
+ pci_reg_base);
+
+ /* Set the BCRs to enable PCI access */
+ reg = ioread32(bcr);
+ reg |= 0x80000;
+ iowrite32(reg, bcr);
+
+ /* Turn the clocks back on (not done in reset)*/
+ pcic_writel(0, SH4_PCICLKR);
+ /* Clear Powerdown IRQs (not done in reset) */
+ word = SH4_PCIPINT_D3 | SH4_PCIPINT_D0;
+ pcic_writel(word, SH4_PCIPINT);
+
+ /* set the command/status bits to:
+ * Wait Cycle Control + Parity Enable + Bus Master +
+ * Mem space enable
+ */
+ word = PCI_COMMAND_WAIT | PCI_COMMAND_PARITY |
+ PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pcic_writel(word, PCI_COMMAND);
+
+ /* define this host as the host bridge */
+ word = PCI_BASE_CLASS_BRIDGE << 24;
+ pcic_writel(word, PCI_CLASS_REVISION);
+
+ /* Set IO and Mem windows to local address
+ * Make PCI and local address the same for easy 1 to 1 mapping
+ */
+ word = memory_end - memory_start - 1;
+ pcic_writel(word, SH4_PCILSR0);
+ /* Set the values on window 0 PCI config registers */
+ word = P2SEGADDR(__pa(memory_start));
+ pcic_writel(word, SH4_PCILAR0);
+ pcic_writel(word, PCI_BASE_ADDRESS_1);
+
+ set_pci_bcr(pci_reg_base, bcr, (__pa(memory_start) >> 27) & 0x07);
+
+ /* configure the wait control registers */
+ word = ioread32(bcr + SH7751_WCR1);
+ pcic_writel(word, SH4_PCIWCR1);
+ word = ioread32(bcr + SH7751_WCR2);
+ pcic_writel(word, SH4_PCIWCR2);
+ word = ioread32(bcr + SH7751_WCR3);
+ pcic_writel(word, SH4_PCIWCR3);
+ word = ioread32(bcr + SH7751_MCR);
+ pcic_writel(word, SH4_PCIMCR);
+
+ match = of_match_node(fixup_of_match, pdev->dev.of_node);
+ if (match) {
+ fixup_fn = match->data;
+ fixup_fn(pci_reg_base, bcr);
+ }
+ /*
+ * SH7751 init done, set central function init complete
+ * use round robin mode to stop a device starving/overruning
+ */
+ word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_ARBM;
+ pcic_writel(word, SH4_PCICR);
+
+ return pci_host_common_probe(pdev, &ecm_ops);
+}
+
+static __refdata struct platform_driver sh7751_pci_driver = {
+ .driver = {
+ .name = "sh7751-pci",
+ .of_match_table = sh7751_pci_of_match,
+ },
+ .probe = sh7751_pci_probe,
+};
+builtin_platform_driver(sh7751_pci_driver);
--
2.7.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
