Re: [PATCH v2] arm64: dts: hikey: name the GPIO lines

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Linus,

On 24/06/2016 00:06, Linus Walleij wrote:
> This names the GPIO lines on the HiKey board in accordance with
> the 96Board Specification for especially the Low Speed External
> Connector: "GPIO-A" thru "GPIO-L".
> 
> This will make these line names reflect through to userspace
> so that they can easily be identified and used with the new
> character device ABI.
> 
> Some care has been taken to name all lines, not just those used
> by the external connectors, also lines that are muxed into some
> other function than GPIO: these are named "[FOO]" so that users
> can see with lsgpio what all lines are used for.
> 
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: John Stultz <john.stultz@xxxxxxxxxx>
> Cc: Rob Herring <robh@xxxxxxxxxx>
> Cc: David Mandala <david.mandala@xxxxxxxxxx>
> Cc: Haojian Zhuang <haojian.zhuang@xxxxxxxxxx>
> Cc: Wei Xu <xuwei5@xxxxxxxxxxxxx>
> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>

Applied to hisilicon soc tree.
Thanks!

Best Regards,
Wei

> ---
> ChangeLog v1->v2:
> - Use the right property name: old patch using "gpio-names" rather
>   than "gpio-line-names" that we agreed upon. Sorry...
> 
> This would be nice to have merged for kernel v4.8 so that the
> new chardev ABI can be used to obtain the lines for the external
> connector and use them from userspace from this kernel version.
> ---
>  arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 143 +++++++++++++++++++++++++
>  1 file changed, 143 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> index e92a30c87a82..593c7e43de79 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
> @@ -66,6 +66,149 @@
>  			status = "ok";
>  		};
>  
> +		/*
> +		 * Legend: proper name = the GPIO line is used as GPIO
> +		 *         NC = not connected (not routed from the SoC)
> +		 *         "[PER]" = pin is muxed for peripheral (not GPIO)
> +		 *         "" = no idea, schematic doesn't say, could be
> +		 *              unrouted (not connected to any external pin)
> +		 *         LSEC = Low Speed External Connector
> +		 *         HSEC = High Speed External Connector
> +		 *
> +		 * Pin assignments taken from LeMaker and CircuitCo Schematics
> +		 * Rev A1.
> +		 *
> +		 * For the lines routed to the external connectors the
> +		 * lines are named after the 96Boards CE Specification 1.0,
> +		 * Appendix "Expansion Connector Signal Description".
> +		 *
> +		 * When the 96Board naming of a line and the schematic name of
> +		 * the same line are in conflict, the 96Board specification
> +		 * takes precedence, which means that the external UART on the
> +		 * LSEC is named UART0 while the schematic and SoC names this
> +		 * UART2. This is only for the informational lines i.e. "[FOO]",
> +		 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
> +		 * ones actually used for GPIO.
> +		 */
> +		gpio0: gpio@f8011000 {
> +			gpio-line-names = "PWR_HOLD", "DSI_SEL",
> +			"USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
> +			"PWRON_DET", "5V_HUB_EN";
> +		};
> +
> +		gpio1: gpio@f8012000 {
> +			gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
> +			"WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
> +		};
> +
> +		gpio2: gpio@f8013000 {
> +			gpio-line-names =
> +				"GPIO-A", /* LSEC Pin 23: GPIO2_0 */
> +				"GPIO-B", /* LSEC Pin 24: GPIO2_1 */
> +				"GPIO-C", /* LSEC Pin 25: GPIO2_2 */
> +				"GPIO-D", /* LSEC Pin 26: GPIO2_3 */
> +				"GPIO-E", /* LSEC Pin 27: GPIO2_4 */
> +				"USB_ID_DET", "USB_VBUS_DET",
> +				"GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
> +		};
> +
> +		gpio3: gpio@f8014000 {
> +			gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
> +			"WLAN_ACTIVE", "NC", "NC";
> +		};
> +
> +		gpio4: gpio@f7020000 {
> +			gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
> +			"USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
> +		};
> +
> +		gpio5: gpio@f7021000 {
> +			gpio-line-names = "NC", "NC",
> +			"[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
> +			"[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
> +			"[AUX_SSI1]", "NC",
> +			"[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
> +			"[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
> +		};
> +
> +		gpio6: gpio@f7022000 {
> +			gpio-line-names =
> +			"[SPI0_DIN]", /* Pin 10: SPI0_DI */
> +			"[SPI0_DOUT]", /* Pin 14: SPI0_DO */
> +			"[SPI0_CS]", /* Pin 12: SPI0_CS_N */
> +			"[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
> +			"NC", "NC", "NC",
> +			"GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
> +		};
> +
> +		gpio7: gpio@f7023000 {
> +			gpio-line-names = "NC", "NC", "NC", "NC",
> +			"[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
> +			"[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
> +			"NC", "NC";
> +		};
> +
> +		gpio8: gpio@f7024000 {
> +			gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
> +			"", "", "", "", "", "";
> +		};
> +
> +		gpio9: gpio@f7025000 {
> +			gpio-line-names = "",
> +			"GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
> +			"GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
> +			"NC", "NC", "NC", "NC", "[ISP_CCLK0]";
> +		};
> +
> +		gpio10: gpio@f7026000 {
> +			gpio-line-names = "BOOT_SEL",
> +			"[ISP_CCLK1]",
> +			"GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
> +			"GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
> +			"NC", "NC",
> +			"[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
> +			"[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
> +		};
> +
> +		gpio11: gpio@f7027000 {
> +			gpio-line-names =
> +			"[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
> +			"[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
> +			"", "NC", "NC", "NC", "", "";
> +		};
> +
> +		gpio12: gpio@f7028000 {
> +			gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
> +			"[BT_PCM_DO]",
> +			"NC", "NC", "NC", "NC",
> +			"GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
> +		};
> +
> +		gpio13: gpio@f7029000 {
> +			gpio-line-names = "[UART0_RX]", "[UART0_TX]",
> +			"[BT_UART1_CTS]", "[BT_UART1_RTS]",
> +			"[BT_UART1_RX]", "[BT_UART1_TX]",
> +			"[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
> +			"[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
> +		};
> +
> +		gpio14: gpio@f702a000 {
> +			gpio-line-names =
> +			"[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
> +			"[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
> +			"[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
> +			"[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
> +			"[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
> +			"[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
> +			"[I2C2_SCL]", "[I2C2_SDA]";
> +		};
> +
> +		gpio15: gpio@f702b000 {
> +			gpio-line-names = "", "", "", "", "", "", "NC", "";
> +		};
> +
> +		/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
> +
>  		dwmmc_2: dwmmc2@f723f000 {
>  			ti,non-removable;
>  			non-removable;
> 

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux