This patch adds the device tree support for FSL LS2088A SoC based on ARMv8 architecture. Following levels of DTSI/DTS files have been created for the LS2088A SoC family: - fsl-ls2088a.dtsi: DTS-Include file for FSL LS2088A SoC. - fsl-ls2088a-qds.dts: DTS file for FSL LS2088A QDS board. - fsl-ls2088a-rdb.dts: DTS file for FSL LS2088A RDB board. Signed-off-by: Abhimanyu Saini <abhimanyu.saini@xxxxxxx> --- arch/arm64/boot/dts/freescale/Makefile | 2 + arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts | 211 +++++++ arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts | 166 +++++ arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi | 703 ++++++++++++++++++++++ 4 files changed, 1082 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 1b7783d..60ff96a 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -3,6 +3,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts new file mode 100644 index 0000000..2b8d9f3 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts @@ -0,0 +1,211 @@ +/* + * Device Tree file for Freescale LS2088A QDS Board. + * + * Copyright (C) 2016, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@xxxxxxx> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +/include/ "fsl-ls2088a.dtsi" + +/ { + model = "Freescale Layerscape 2088A QDS Board"; + compatible = "fsl,ls2088a-qds", "fsl,ls2088a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; + +}; + +&esdhc { + status = "okay"; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x80000000 0x08000000 + 0x2 0x0 0x5 0x30000000 0x00010000 + 0x3 0x0 0x5 0x20000000 0x00010000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@2,0 { + compatible = "fsl,ifc-nand"; + reg = <0x2 0x0 0x10000>; + }; + + cpld@3,0 { + reg = <0x3 0x0 0x10000>; + compatible = "fsl,ls2088aqds-fpga", "fsl,fpga-qixis"; + }; +}; + +&i2c0 { + status = "okay"; + pca9547@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x00>; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x02>; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <500>; + }; + + ina220@41 { + compatible = "ti,ina220"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&i2c1 { + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +&dspi { + status = "okay"; + dflash0: n25q128a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <0>; + }; + dflash1: sst25wf040b { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <1>; + }; + dflash2: en25s64 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <2>; + }; +}; + +&qspi { + status = "okay"; + flash0: s25fl256s1@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <20000000>; + reg = <0>; + }; + flash2: s25fl256s1@2 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts new file mode 100644 index 0000000..6d403bc --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts @@ -0,0 +1,166 @@ +/* + * Device Tree file for Freescale LS2088A RDB Board. + * + * Copyright (C) 2016, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@xxxxxxx> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +/include/ "fsl-ls2088a.dtsi" + +/ { + model = "Freescale Layerscape 2088A RDB Board"; + compatible = "fsl,ls2088a-rdb", "fsl,ls2088a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; +}; + +&esdhc { + status = "okay"; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x80000000 0x08000000 + 0x2 0x0 0x5 0x30000000 0x00010000 + 0x3 0x0 0x5 0x20000000 0x00010000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@2,0 { + compatible = "fsl,ifc-nand"; + reg = <0x2 0x0 0x10000>; + }; + + cpld@3,0 { + reg = <0x3 0x0 0x10000>; + compatible = "fsl,ls2088aqds-fpga", "fsl,fpga-qixis"; + }; + +}; + +&i2c0 { + status = "okay"; + pca9547@75 { + compatible = "nxp,pca9547"; + reg = <0x75>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x01>; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&i2c1 { + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +&dspi { + status = "okay"; + dflash0: n25q512a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <0>; + }; +}; + +&qspi { + status = "disabled"; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi new file mode 100644 index 0000000..687ab5a --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi @@ -0,0 +1,703 @@ +/* + * Device Tree Include file for Freescale Layerscape-2088A family SoC. + * + * Copyright (C) 2016, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@xxxxxxx> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/ { + compatible = "fsl,ls2088a"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x0>; + clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x1>; + clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; + }; + + cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x100>; + clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; + }; + + cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x101>; + clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; + }; + + cpu@200 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x200>; + clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; + }; + + cpu@201 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x201>; + clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; + }; + + cpu@300 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x300>; + clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; + }; + + cpu@301 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x301>; + clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; + }; + + cluster0_l2: l2-cache0 { + compatible = "cache"; + }; + + cluster1_l2: l2-cache1 { + compatible = "cache"; + }; + + cluster2_l2: l2-cache2 { + compatible = "cache"; + }; + + cluster3_l2: l2-cache3 { + compatible = "cache"; + }; + }; + + sysclk: sysclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "sysclk"; + }; + + gic: interrupt-controller@6000000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06100000 0 0x100000>, /* GICR (RD_base + SGI_base) */ + <0x0 0x0c0c0000 0 0x2000>, /* GICC */ + <0x0 0x0c0d0000 0 0x1000>, /* GICH */ + <0x0 0x0c0e0000 0 0x20000>; /* GICV */ + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + interrupt-controller; + interrupts = <1 9 0x4>; + + its: gic-its@6020000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x6020000 0 0x20000>; + }; + }; + + reboot { + compatible ="syscon-reboot"; + regmap = <&rstcr>; + offset = <0x0>; + mask = <0x2>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */ + <1 14 0x8>, /* Physical Non-Secure PPI, active-low */ + <1 11 0x8>, /* Virtual PPI, active-low */ + <1 10 0x8>; /* Hypervisor PPI, active-low */ + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <1 7 0x8>; /* PMU PPI, Level low type */ + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + rstcr: syscon@1e60000 { + compatible = "fsl,ls2088a-rstcr", "fsl,ls2080a-rstcr", + "syscon"; + reg = <0x0 0x1e60000 0x0 0x4>; + }; + + clockgen: clocking@1300000 { + compatible = "fsl,ls2088a-clockgen"; + reg = <0 0x1300000 0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; + + serial0: serial@21c0500 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0500 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 0x4>; /* Level high type */ + }; + + serial1: serial@21c0600 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0600 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 0x4>; /* Level high type */ + }; + + cluster1_core0_watchdog: wdt@c000000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc000000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster1_core1_watchdog: wdt@c010000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc010000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster2_core0_watchdog: wdt@c100000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc100000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster2_core1_watchdog: wdt@c110000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc110000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster3_core0_watchdog: wdt@c200000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc200000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster3_core1_watchdog: wdt@c210000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc210000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster4_core0_watchdog: wdt@c300000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc300000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster4_core1_watchdog: wdt@c310000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc310000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + fsl_mc: fsl-mc@80c000000 { + compatible = "fsl,qoriq-mc"; + reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ + <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ + msi-parent = <&its>; + #address-cells = <3>; + #size-cells = <1>; + + /* + * Region type 0x0 - MC portals + * Region type 0x1 - QBMAN portals + */ + ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000 + 0x1 0x0 0x0 0x8 0x18000000 0x8000000>; + + /* + * Define the maximum number of MACs present on the SoC. + */ + dpmacs { + #address-cells = <1>; + #size-cells = <0>; + + dpmac1: dpmac@1 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x1>; + }; + + dpmac2: dpmac@2 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x2>; + }; + + dpmac3: dpmac@3 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x3>; + }; + + dpmac4: dpmac@4 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x4>; + }; + + dpmac5: dpmac@5 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x5>; + }; + + dpmac6: dpmac@6 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x6>; + }; + + dpmac7: dpmac@7 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x7>; + }; + + dpmac8: dpmac@8 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x8>; + }; + + dpmac9: dpmac@9 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x9>; + }; + + dpmac10: dpmac@a { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xa>; + }; + + dpmac11: dpmac@b { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xb>; + }; + + dpmac12: dpmac@c { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xc>; + }; + + dpmac13: dpmac@d { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xd>; + }; + + dpmac14: dpmac@e { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xe>; + }; + + dpmac15: dpmac@f { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xf>; + }; + + dpmac16: dpmac@10 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x10>; + }; + }; + }; + + smmu: iommu@5000000 { + compatible = "arm,mmu-500"; + reg = <0 0x5000000 0 0x800000>; + #global-interrupts = <12>; + interrupts = <0 13 4>, /* global secure fault */ + <0 14 4>, /* combined secure interrupt */ + <0 15 4>, /* global non-secure fault */ + <0 16 4>, /* combined non-secure interrupt */ + /* performance counter interrupts 0-7 */ + <0 211 4>, <0 212 4>, + <0 213 4>, <0 214 4>, + <0 215 4>, <0 216 4>, + <0 217 4>, <0 218 4>, + /* per context interrupt, 64 interrupts */ + <0 146 4>, <0 147 4>, + <0 148 4>, <0 149 4>, + <0 150 4>, <0 151 4>, + <0 152 4>, <0 153 4>, + <0 154 4>, <0 155 4>, + <0 156 4>, <0 157 4>, + <0 158 4>, <0 159 4>, + <0 160 4>, <0 161 4>, + <0 162 4>, <0 163 4>, + <0 164 4>, <0 165 4>, + <0 166 4>, <0 167 4>, + <0 168 4>, <0 169 4>, + <0 170 4>, <0 171 4>, + <0 172 4>, <0 173 4>, + <0 174 4>, <0 175 4>, + <0 176 4>, <0 177 4>, + <0 178 4>, <0 179 4>, + <0 180 4>, <0 181 4>, + <0 182 4>, <0 183 4>, + <0 184 4>, <0 185 4>, + <0 186 4>, <0 187 4>, + <0 188 4>, <0 189 4>, + <0 190 4>, <0 191 4>, + <0 192 4>, <0 193 4>, + <0 194 4>, <0 195 4>, + <0 196 4>, <0 197 4>, + <0 198 4>, <0 199 4>, + <0 200 4>, <0 201 4>, + <0 202 4>, <0 203 4>, + <0 204 4>, <0 205 4>, + <0 206 4>, <0 207 4>, + <0 208 4>, <0 209 4>; + mmu-masters = <&fsl_mc 0x300 0>; + }; + + dspi: dspi@2100000 { + status = "disabled"; + compatible = "fsl,ls2088a-dspi", "fsl,ls2085a-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2100000 0x0 0x10000>; + interrupts = <0 26 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + }; + + esdhc: esdhc@2140000 { + status = "disabled"; + compatible = "fsl,ls2088a-esdhc", "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <0 28 0x4>; /* Level high type */ + clock-frequency = <0>; /* Updated by bootloader */ + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + little-endian; + bus-width = <4>; + }; + + gpio0: gpio@2300000 { + compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@2310000 { + compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2310000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2320000 { + compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2320000 0x0 0x10000>; + interrupts = <0 37 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@2330000 { + compatible = "fsl,ls2088a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2330000 0x0 0x10000>; + interrupts = <0 37 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + i2c0: i2c@2000000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts = <0 34 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c1: i2c@2010000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2010000 0x0 0x10000>; + interrupts = <0 34 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c2: i2c@2020000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2020000 0x0 0x10000>; + interrupts = <0 35 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c3: i2c@2030000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2030000 0x0 0x10000>; + interrupts = <0 35 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + ifc: ifc@2240000 { + compatible = "fsl,ifc", "simple-bus"; + reg = <0x0 0x2240000 0x0 0x20000>; + interrupts = <0 21 0x4>; /* Level high type */ + little-endian; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x5 0x80000000 0x08000000 + 2 0 0x5 0x30000000 0x00010000 + 3 0 0x5 0x20000000 0x00010000>; + }; + + qspi: quadspi@20c0000 { + status = "disabled"; + compatible = "fsl,ls2088a-qspi", "fsl,ls1021a-qspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>; + reg-names = "QuadSPI", "QuadSPI-memory"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "qspi_en", "qspi"; + }; + + pcie1: pcie@3400000 { + compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie", + "snps,dw-pcie"; + reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */ + 0x20 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 108 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x20 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x20 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>, + <0000 0 0 2 &gic 0 0 0 110 4>, + <0000 0 0 3 &gic 0 0 0 111 4>, + <0000 0 0 4 &gic 0 0 0 112 4>; + }; + + pcie2: pcie@3500000 { + compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie", + "snps,dw-pcie"; + reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */ + 0x28 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 113 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x28 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x28 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>, + <0000 0 0 2 &gic 0 0 0 115 4>, + <0000 0 0 3 &gic 0 0 0 116 4>, + <0000 0 0 4 &gic 0 0 0 117 4>; + }; + + pcie3: pcie@3600000 { + compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie", + "snps,dw-pcie"; + reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */ + 0x30 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 118 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <8>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x30 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x30 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>, + <0000 0 0 2 &gic 0 0 0 120 4>, + <0000 0 0 3 &gic 0 0 0 121 4>, + <0000 0 0 4 &gic 0 0 0 122 4>; + }; + + pcie4: pcie@3700000 { + compatible = "fsl,ls2088a-pcie", "fsl,ls2080a-pcie", + "snps,dw-pcie"; + reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */ + 0x38 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <0 123 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x38 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x38 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>, + <0000 0 0 2 &gic 0 0 0 125 4>, + <0000 0 0 3 &gic 0 0 0 126 4>, + <0000 0 0 4 &gic 0 0 0 127 4>; + }; + + sata0: sata@3200000 { + status = "disabled"; + compatible = "fsl,ls2088a-ahci", "fsl,ls2080a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <0 133 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + }; + + sata1: sata@3210000 { + status = "disabled"; + compatible = "fsl,ls2088a-ahci", "fsl,ls2080a-ahci"; + reg = <0x0 0x3210000 0x0 0x10000>; + interrupts = <0 136 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + }; + + usb0: usb3@3100000 { + status = "disabled"; + compatible = "snps,dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <0 80 0x4>; /* Level high type */ + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + }; + + usb1: usb3@3110000 { + status = "disabled"; + compatible = "snps,dwc3"; + reg = <0x0 0x3110000 0x0 0x10000>; + interrupts = <0 81 0x4>; /* Level high type */ + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + }; + + ccn@4000000 { + compatible = "arm,ccn-504"; + reg = <0x0 0x04000000 0x0 0x01000000>; + interrupts = <0 12 4>; + }; + }; +}; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html