The high-speed phy on qcom SoCs is controlled via the ULPI
viewport.
Cc: Kishon Vijay Abraham I <kishon@xxxxxx>
Cc: <devicetree@xxxxxxxxxxxxxxx>
Signed-off-by: Stephen Boyd <stephen.boyd@xxxxxxxxxx>
---
.../devicetree/bindings/phy/qcom,usb-hs-phy.txt | 71 ++++++
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hs.c | 283 +++++++++++++++++++++
4 files changed, 363 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hs.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
new file mode 100644
index 000000000000..2bd22c53cee0
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
@@ -0,0 +1,71 @@
+Qualcomm's USB HS PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hs-phy"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for the reference and sleep
+ clocks
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "ref" and "sleep" for the reference and sleep
+ clocks respectively
+
+- resets:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain the phy and POR resets
+
+- reset-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy" and "por" for the phy and POR resets
+ respectively
+
+- v3p3-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 3.3V supply
+
+- v1p8-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 1.8V supply
+
+- qcom,init-seq:
+ Usage: optional
+ Value type: <u8 array>
+ Definition: Should contain a sequence of ULPI register and address pairs to
+ program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related
+ to Device Mode Eye Diagram test.
+
+EXAMPLE
+
+otg: usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hs-phy";
+ #phy-cells = <0>;
+ clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "sleep";
+ resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
+ reset-names = "phy", "por";
+ v3p3-supply = <&pm8941_l24>;
+ v1p8-supply = <&pm8941_l6>;
+ qcom,init-seq = /bits/ 8 <0x81 0x63>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index a2866949dc97..cfb3ded0896d 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -406,6 +406,14 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HS
+ tristate "Qualcomm USB HS PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB high-speed ULPI compliant phy on Qualcomm
+ chipsets.
+
config PHY_QCOM_USB_HSIC
tristate "Qualcomm USB HSIC ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 982e84a290ec..21435fc0b656 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
diff --git a/drivers/phy/phy-qcom-usb-hs.c b/drivers/phy/phy-qcom-usb-hs.c
new file mode 100644
index 000000000000..8be83100ecd9
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hs.c
@@ -0,0 +1,283 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of_device.h>
+#include <linux/reset.h>
+#include <linux/extcon.h>
+#include <linux/notifier.h>
+#include <linux/usb/of.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_PWR_CLK_MNG_REG 0x88
+# define ULPI_PWR_OTG_COMP_DISABLE BIT(0)
+
+#define ULPI_MISC_A 0x96
+# define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
+# define ULPI_MISC_A_VBUSVLDEXT BIT(0)
+
+
+struct ulpi_seq {
+ u8 addr;
+ u8 val;
+};
+
+struct qcom_usb_hs_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct clk *ref_clk;
+ struct clk *sleep_clk;
+ struct regulator *v1p8;
+ struct regulator *v3p3;
+ struct reset_control *reset;
+ struct ulpi_seq *init_seq;
+ struct notifier_block vbus_notify;
+ struct extcon_dev *vbus_edev;
+ struct extcon_dev *id_edev;
+ enum usb_dr_mode dr_mode;
+};
+
+static int
+qcom_usb_hs_phy_vbus_notifier(struct notifier_block *nb, unsigned long event,
+ void *ptr)
+{
+ struct qcom_usb_hs_phy *uphy;
+ int is_host;
+ u8 addr;
+
+ uphy = container_of(nb, struct qcom_usb_hs_phy, vbus_notify);
+ is_host = extcon_get_cable_state_(uphy->id_edev, EXTCON_USB_HOST);
+ if (is_host < 0)
+ is_host = 0; /* No id event means always a peripheral */
+
+ if (event && !is_host)
+ addr = ULPI_SET(ULPI_MISC_A);
+ else
+ addr = ULPI_CLR(ULPI_MISC_A);
+
+ return ulpi_write(uphy->ulpi, addr,
+ ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static int qcom_usb_hs_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ const struct ulpi_seq *seq;
+ int ret, state;
+
+ ret = clk_prepare_enable(uphy->ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ ret = regulator_set_voltage(uphy->v1p8, 1800000, 1800000);
+ if (ret)
+ goto err_1p8;
+ ret = regulator_set_load(uphy->v1p8, 50000);
+ if (ret < 0)
+ goto err_1p8;
+
+ ret = regulator_enable(uphy->v1p8);
+ if (ret)
+ goto err_1p8;
+
+ ret = regulator_set_voltage_triplet(uphy->v3p3, 3050000, 3300000,
+ 3300000);
+ if (ret)
+ goto err_3p3;
+
+ ret = regulator_set_load(uphy->v3p3, 50000);
+ if (ret < 0)
+ goto err_3p3;
+
+ ret = regulator_enable(uphy->v3p3);
+ if (ret)
+ goto err_3p3;
+
+ for (seq = uphy->init_seq; seq->addr; seq++) {
+ ret = ulpi_write(ulpi, seq->addr, seq->val);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->reset) {
+ ret = reset_control_reset(uphy->reset);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->vbus_edev) {
+ ulpi_write(ulpi, ULPI_SET(ULPI_PWR_CLK_MNG_REG),
+ ULPI_PWR_OTG_COMP_DISABLE);
+ state = extcon_get_cable_state_(uphy->vbus_edev, EXTCON_USB);
+ /* setup initial state */
+ qcom_usb_hs_phy_vbus_notifier(&uphy->vbus_notify, state,
+ uphy->vbus_edev);
+ } else {
+ u8 val;
+
+ switch (uphy->dr_mode) {
+ case USB_DR_MODE_OTG:
+ val = ULPI_INT_IDGRD;
+ case USB_DR_MODE_PERIPHERAL:
+ val |= ULPI_INT_SESS_VALID;
+ break;
+ default:
+ val = 0;
+ }
+
+ ret = ulpi_write(ulpi, ULPI_USB_INT_EN_RISE, val);
+ if (ret)
+ goto err_ulpi;
+ ret = ulpi_write(ulpi, ULPI_USB_INT_EN_FALL, val);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ return 0;
+err_ulpi:
+ regulator_disable(uphy->v3p3);
+err_3p3:
+ regulator_disable(uphy->v1p8);
+err_1p8:
+ clk_disable_unprepare(uphy->sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->ref_clk);
+ return ret;
+}
+
+static int qcom_usb_hs_phy_power_off(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+
+ regulator_disable(uphy->v3p3);
+ regulator_disable(uphy->v1p8);
+ clk_disable_unprepare(uphy->sleep_clk);
+ clk_disable_unprepare(uphy->ref_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hs_phy_ops = {
+ .power_on = qcom_usb_hs_phy_power_on,
+ .power_off = qcom_usb_hs_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hs_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hs_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+ struct regulator *reg;
+ struct reset_control *reset;
+ int size;
+ int ret;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+ uphy->ulpi = ulpi;
+ uphy->dr_mode = of_usb_get_dr_mode_by_phy(ulpi->dev.of_node);
+
+ size = of_property_count_u8_elems(ulpi->dev.of_node, "qcom,init-seq");
+ if (size < 0)
+ size = 0;
+ uphy->init_seq = devm_kmalloc_array(&ulpi->dev, (size / 2) + 1,
+ sizeof(*uphy->init_seq), GFP_KERNEL);
+ if (!uphy->init_seq)
+ return -ENOMEM;
+ ret = of_property_read_u8_array(ulpi->dev.of_node, "qcom,init-seq",
+ (u8 *)uphy->init_seq, size);
+ if (ret && size)
+ return ret;
+ /* NUL terminate */
+ uphy->init_seq[size / 2].addr = uphy->init_seq[size / 2].val = 0;
+
+ uphy->ref_clk = clk = devm_clk_get(&ulpi->dev, "ref");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->sleep_clk = clk = devm_clk_get(&ulpi->dev, "sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->v1p8 = reg = devm_regulator_get(&ulpi->dev, "v1p8");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->v3p3 = reg = devm_regulator_get(&ulpi->dev, "v3p3");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->reset = reset = devm_reset_control_get(&ulpi->dev, "por");
+ if (IS_ERR(reset)) {
+ if (PTR_ERR(reset) == -EPROBE_DEFER)
+ return PTR_ERR(reset);
+ uphy->reset = NULL;
+ }
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hs_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+
+ uphy->vbus_edev = extcon_get_edev_by_phandle(&ulpi->dev, 0);
+ if (IS_ERR(uphy->vbus_edev)) {
+ if (PTR_ERR(uphy->vbus_edev) != -ENODEV)
+ return PTR_ERR(uphy->vbus_edev);
+ uphy->vbus_edev = NULL;
+ }
+
+ uphy->id_edev = extcon_get_edev_by_phandle(&ulpi->dev, 1);
+ if (IS_ERR(uphy->id_edev)) {
+ if (PTR_ERR(uphy->id_edev) != -ENODEV)
+ return PTR_ERR(uphy->id_edev);
+ uphy->id_edev = NULL;
+ }
+
+ if (uphy->vbus_edev) {
+ uphy->vbus_notify.notifier_call = qcom_usb_hs_phy_vbus_notifier;
+ ret = extcon_register_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ return ret;
+ }
+
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hs_phy_match[] = {
+ { .compatible = "qcom,usb-hs-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hs_phy_match);
+
+static struct ulpi_driver qcom_usb_hs_phy_driver = {
+ .probe = qcom_usb_hs_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hs_phy",
+ .of_match_table = qcom_usb_hs_phy_match
+ },
+};
+module_ulpi_driver(qcom_usb_hs_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HS phy");
+MODULE_LICENSE("GPL v2");
--
2.9.0.rc2.8.ga28705d
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
