Hi,
On Mon, Jun 20, 2016 at 7:26 PM, Peter Chen <hzpeterchen@xxxxxxxxx> wrote:
> On Fri, Jun 17, 2016 at 12:16:48PM -0500, Rob Herring wrote:
>> On Fri, Jun 17, 2016 at 5:09 AM, Peter Chen <peter.chen@xxxxxxx> wrote:
>> > Add binding doc for generic usb power sequence driver, and update
>> > generic usb device binding-doc accordingly.
>> >
>> > Signed-off-by: Peter Chen <peter.chen@xxxxxxx>
>> > ---
>> > .../bindings/power/pwrseq/pwrseq-usb-generic.txt | 31 ++++++++++++++++++++++
>> > .../devicetree/bindings/usb/usb-device.txt | 2 ++
>> > 2 files changed, 33 insertions(+)
>> > create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-usb-generic.txt
>> >
>> > diff --git a/Documentation/devicetree/bindings/power/pwrseq/pwrseq-usb-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-usb-generic.txt
>> > new file mode 100644
>> > index 0000000..8ad98382
>> > --- /dev/null
>> > +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-usb-generic.txt
>> > @@ -0,0 +1,31 @@
>> > +The power sequence for generic USB Devices
>> > +
>> > +Some hard-wired USB devices need to do power sequence to let the
>> > +device work normally, the typical power sequence like: enable USB
>> > +PHY clock, toggle reset pin, etc. But current Linux USB driver
>> > +lacks of such code to do it, it may cause some hard-wired USB devices
>> > +works abnormal or can't be recognized by controller at all. The
>> > +power sequence will be done before this device can be found at USB
>> > +bus.
>> > +
>> > +Required properties:
>> > +- compatible : contains "usb-pwrseq-generic".
>>
>> In case I have not been clear, no.
>>
>> I am not going to accept anything along the lines of the current mmc
>> pwrseq. I am basically okay with Krzysztof's proposal as it is *only*
>> an added property and not a duplication of information. I'd suggest
>> you figure out how to make the kernel work with that rather than
>> trying to work-around whatever kernel limitations there are.
>>
>
> I see.
>
> Would you agree with below:
>
> &usbotg1 {
> vbus-supply = <®_usb_otg1_vbus>;
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb_otg1_id>;
> status = "okay";
>
> #address-cells = <1>;
> #size-cells = <0>;
> hub: genesys@1 {
> compatible = "usb5e3,608";
> reg = <1>;
>
> power-sequence;
> reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */
> reset-duration-us = <10>;
> clocks = <&clks IMX6SX_CLK_CKO>;
>
> #address-cells = <1>;
> #size-cells = <0>;
> ethernet: asix@1 {
> compatible = "usbb95,1708";
> reg = <1>;
>
> power-sequence;
> reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */
> reset-duration-us = <15>;
> clocks = <&clks IMX6SX_CLK_IPG>;
> };
> };
> };
>
> If the node has property "power-sequence", the pwrseq core will create
> related platform device, and the driver under pwrseq driver will handle
> power sequence stuffs. The property below "power-sequence" will be
> handled at pwrseq driver.
Isn't this binding what Krzysztof proposed? His series also provides example
code for enabling USB device power sequencing. Does it not work for you?
Having 2 series by 2 separate people doing the same thing but slightly
different is very confusing.
Regards
ChenYu
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
