Re: [PATCH v2] ARM: dts: sun8i: Add dts file for Olimex A33-OLinuXino

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Mon, Jun 20, 2016 at 2:42 PM, Stefan Mavrodiev
<stefan.mavrodiev@xxxxxxxxx> wrote:
> A33-OLinuXino is A33 development board designed by Olimex LTD.
>
> It has AXP233 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
> headphone and mic jacks, connector for LiPo battery and optional
> 4GB NAND Flash.
>
> It has two 40-pin headers. One for LCD panel, and one for
> additional modules. Also there is CSI/DSI connector.
>
> Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@xxxxxxxxx>
> ---
> Changes for v2:
>         - Removed unused power nodes
>         - Removed default-trigger for green led
>         - Removed "always-on" option for LCD power
>
>  arch/arm/boot/dts/Makefile                |   1 +
>  arch/arm/boot/dts/sun8i-a33-olinuxino.dts | 207 ++++++++++++++++++++++++++++++
>  2 files changed, 208 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-a33-olinuxino.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 970e906..b78f363 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -760,6 +760,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>         sun8i-a33-ippo-q8h-v1.2.dtb \
>         sun8i-a33-q8-tablet.dtb \
>         sun8i-a33-sinlinx-sina33.dtb \
> +       sun8i-a33-olinuxino.dtb \
>         sun8i-a83t-allwinner-h8homlet-v2.dtb \
>         sun8i-a83t-cubietruck-plus.dtb \
>         sun8i-h3-orangepi-2.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts
> new file mode 100644
> index 0000000..14fa801
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts
> @@ -0,0 +1,207 @@
> +/*
> + * Copyright 2016 - Stefan Mavrodiev <stefan.mavrodiev@xxxxxxxxx>
> + *                  Olimex LTD. <support@xxxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-a33.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +       model = "A33-OLinuXino";
> +       compatible = "allwinner,sun8i-a33";
> +
> +       aliases {
> +               serial0 = &uart0;
> +       };
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&led_pin_olinuxino>;
> +
> +               green {
> +                       label = "olinuxino:green:usr";
> +                       gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* LED2 */
> +               };
> +       };
> +};
> +
> +&ehci0 {
> +       status = "okay";
> +};
> +
> +&ohci0 {
> +       status = "okay";
> +};

Please sort the nodes alphabetically.

> +
> +&mmc0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
> +       vmmc-supply = <&reg_dcdc1>;
> +       bus-width = <4>;
> +       cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
> +       cd-inverted;
> +       status = "okay";
> +};
> +
> +&pio {
> +       mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
> +               allwinner,pins = "PB4";
> +               allwinner,function = "gpio_in";
> +               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +       };
> +
> +       led_pin_olinuxino: led_pins@0 {
> +               allwinner,pins = "PB7";
> +               allwinner,function = "gpio_out";
> +               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +       };
> +};
> +
> +&r_rsb {
> +       status = "okay";
> +
> +       axp22x: pmic@3a3 {
> +               compatible = "x-powers,axp223";
> +               reg = <0x3a3>;
> +               interrupt-parent = <&nmi_intc>;
> +               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +               eldoin-supply = <&reg_dcdc1>;
> +       };
> +};
> +
> +#include "axp22x.dtsi"
> +
> +&reg_dcdc1 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-dsi";
> +};
> +
> +&reg_dc1sw {
> +       regulator-name = "vcc-lcd";
> +};
> +
> +&reg_dcdc2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <900000>;
> +       regulator-max-microvolt = <1400000>;
> +       regulator-name = "vdd-sys";
> +};
> +
> +&reg_dcdc3 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <900000>;
> +       regulator-max-microvolt = <1400000>;
> +       regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc5 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1500000>;
> +       regulator-max-microvolt = <1500000>;
> +       regulator-name = "vcc-dram";
> +};
> +
> +&reg_dc5ldo {
> +       regulator-always-on;
> +       regulator-min-microvolt = <900000>;
> +       regulator-max-microvolt = <1400000>;
> +       regulator-name = "vdd-cpus";
> +};
> +
> +&reg_aldo1 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-io";
> +};
> +
> +&reg_aldo2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <2350000>;
> +       regulator-max-microvolt = <2650000>;
> +       regulator-name = "vdd-dll";
> +};
> +
> +&reg_aldo3 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-avcc";
> +};

These as well.

> +
> +&reg_rtc_ldo {
> +       regulator-name = "vcc-rtc";
> +};
> +
> +&uart0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&uart0_pins_b>;
> +       status = "okay";
> +};
> +
> +&usb_otg {
> +       dr_mode = "host";
> +       status = "okay";
> +};
> +
> +&usbphy {
> +       usb0_vbus-supply = <&reg_vcc5v0>;
> +       status = "okay";
> +
> +};
> +
> +&simplefb_lcd {
> +       vcc-lcd-supply = <&reg_dc1sw>;
> +};

This one as well.

ChenYu

> --
> 2.8.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux