phy-sun4i-usb now has proper dr_mode handling, it always registers an
extcon, and sends a notify with the mode (even when in peripheral- /
host-only mode) at least once.
So we can simply the sunxi musb glue by always registering its extcon
notifier and relying on sunxi_musb_work() to enable vbus when in
host-only mode.
This also enables host- and peripheral-only mode with vbus monitoring.
Tested-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
Acked-by: Bin Liu <b-liu@xxxxxx>
---
Changes in v2:
-No changes
Changes in v3:
-No changes
Changes in v4:
-Add Maxime's Tested-by
-Add Bin Liu's Acked-by
Changes in v5:
-No changes
---
drivers/usb/musb/sunxi.c | 68 ++++++++++++++++++------------------------------
1 file changed, 25 insertions(+), 43 deletions(-)
diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
index 7650051..a17eb2a 100644
--- a/drivers/usb/musb/sunxi.c
+++ b/drivers/usb/musb/sunxi.c
@@ -256,12 +256,10 @@ static int sunxi_musb_init(struct musb *musb)
writeb(SUNXI_MUSB_VEND0_PIO_MODE, musb->mregs + SUNXI_MUSB_VEND0);
/* Register notifier before calling phy_init() */
- if (musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE) {
- ret = extcon_register_notifier(glue->extcon, EXTCON_USB_HOST,
- &glue->host_nb);
- if (ret)
- goto error_reset_assert;
- }
+ ret = extcon_register_notifier(glue->extcon, EXTCON_USB_HOST,
+ &glue->host_nb);
+ if (ret)
+ goto error_reset_assert;
ret = phy_init(glue->phy);
if (ret)
@@ -275,9 +273,8 @@ static int sunxi_musb_init(struct musb *musb)
return 0;
error_unregister_notifier:
- if (musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE)
- extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
- &glue->host_nb);
+ extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
+ &glue->host_nb);
error_reset_assert:
if (test_bit(SUNXI_MUSB_FL_HAS_RESET, &glue->flags))
reset_control_assert(glue->rst);
@@ -301,9 +298,8 @@ static int sunxi_musb_exit(struct musb *musb)
phy_exit(glue->phy);
- if (musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE)
- extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
- &glue->host_nb);
+ extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
+ &glue->host_nb);
if (test_bit(SUNXI_MUSB_FL_HAS_RESET, &glue->flags))
reset_control_assert(glue->rst);
@@ -315,25 +311,6 @@ static int sunxi_musb_exit(struct musb *musb)
return 0;
}
-static int sunxi_set_mode(struct musb *musb, u8 mode)
-{
- struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
- int ret;
-
- if (mode == MUSB_HOST) {
- ret = phy_power_on(glue->phy);
- if (ret)
- return ret;
-
- set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
- /* Stop musb work from turning vbus off again */
- set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
- musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
- }
-
- return 0;
-}
-
static void sunxi_musb_enable(struct musb *musb)
{
struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
@@ -582,7 +559,6 @@ static const struct musb_platform_ops sunxi_musb_ops = {
.exit = sunxi_musb_exit,
.enable = sunxi_musb_enable,
.disable = sunxi_musb_disable,
- .set_mode = sunxi_set_mode,
.fifo_offset = sunxi_musb_fifo_offset,
.ep_offset = sunxi_musb_ep_offset,
.busctl_offset = sunxi_musb_busctl_offset,
@@ -638,10 +614,6 @@ static int sunxi_musb_probe(struct platform_device *pdev)
return -EINVAL;
}
- glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
- if (!glue)
- return -ENOMEM;
-
memset(&pdata, 0, sizeof(pdata));
switch (usb_get_dr_mode(&pdev->dev)) {
#if defined CONFIG_USB_MUSB_DUAL_ROLE || defined CONFIG_USB_MUSB_HOST
@@ -649,15 +621,13 @@ static int sunxi_musb_probe(struct platform_device *pdev)
pdata.mode = MUSB_PORT_MODE_HOST;
break;
#endif
+#if defined CONFIG_USB_MUSB_DUAL_ROLE || defined CONFIG_USB_MUSB_GADGET
+ case USB_DR_MODE_PERIPHERAL:
+ pdata.mode = MUSB_PORT_MODE_GADGET;
+ break;
+#endif
#ifdef CONFIG_USB_MUSB_DUAL_ROLE
case USB_DR_MODE_OTG:
- glue->extcon = extcon_get_edev_by_phandle(&pdev->dev, 0);
- if (IS_ERR(glue->extcon)) {
- if (PTR_ERR(glue->extcon) == -EPROBE_DEFER)
- return -EPROBE_DEFER;
- dev_err(&pdev->dev, "Invalid or missing extcon\n");
- return PTR_ERR(glue->extcon);
- }
pdata.mode = MUSB_PORT_MODE_DUAL_ROLE;
break;
#endif
@@ -668,6 +638,10 @@ static int sunxi_musb_probe(struct platform_device *pdev)
pdata.platform_ops = &sunxi_musb_ops;
pdata.config = &sunxi_musb_hdrc_config;
+ glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
+ if (!glue)
+ return -ENOMEM;
+
glue->dev = &pdev->dev;
INIT_WORK(&glue->work, sunxi_musb_work);
glue->host_nb.notifier_call = sunxi_musb_host_notifier;
@@ -701,6 +675,14 @@ static int sunxi_musb_probe(struct platform_device *pdev)
}
}
+ glue->extcon = extcon_get_edev_by_phandle(&pdev->dev, 0);
+ if (IS_ERR(glue->extcon)) {
+ if (PTR_ERR(glue->extcon) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ dev_err(&pdev->dev, "Invalid or missing extcon\n");
+ return PTR_ERR(glue->extcon);
+ }
+
glue->phy = devm_phy_get(&pdev->dev, "usb");
if (IS_ERR(glue->phy)) {
if (PTR_ERR(glue->phy) == -EPROBE_DEFER)
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
