Hi,
On Mon, Jun 13, 2016 at 1:08 AM, Shawn Lin <shawn.lin@xxxxxxxxxxxxxx> wrote:
> 在 2016/6/8 6:44, Douglas Anderson 写道:
>>
>> In commit 802ac39a5566 ("mmc: sdhci-of-arasan: fix set_clock when a phy
>> is supported") we added code to power the PHY off and on whenever the
>> clock was changed but we avoided doing the power cycle code when the
>> clock was low speed. Let's now do it always.
>>
>> Although there may be other reasons for power cycling the PHY when the
>> clock changes, one of the main reasons is that we need to give the DLL a
>> chance to re-lock with the new clock.
>>
>> One of the things that the DLL is for is tuning the Receive Clock in
>> HS200 mode and STRB in HS400 mode. Thus it is clear that we should make
>> sure we power cycle the PHY (and wait for the DLL to lock) when we know
>> we'll be in one of these two speed modes. That's what the original code
>> did, though it used the clock rate rather than the speed mode. However,
>> even in speed modes other than HS200,/HS400 the DLL is used for
>> something since it can be clearly observed that the PHY doesn't function
>> properly if you leave the DLL off.
>>
>> Although it appears less important to power cycle the PHY and wait for
>> the DLL to lock when not in HS200/HS400 modes (no bugs were reported),
>> it still seems wise to let the locking always happen nevertheless.
>>
>
> From the design doc, there is no need to off/on phy when not in
> HS200/400, but maybe someone will limit the clk freq by assigning
> max-frequency in DT when in HS200/400, which will make things worse.
>
> So your patch looks sane.
>
>
>> Note: as part of this, we make sure that we never try to turn the PHY on
>> when the clock is off (when the clock rate is 0). The PHY cannot work
>> when the clock is off since its DLL can't lock.
>>
>> This change requires ("phy: rockchip-emmc: Increase lock time
>> allowance") and will cause problems if picked without that change.
>>
>> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
>> ---
>> drivers/mmc/host/sdhci-of-arasan.c | 23 ++++++++---------------
>> 1 file changed, 8 insertions(+), 15 deletions(-)
>>
>> diff --git a/drivers/mmc/host/sdhci-of-arasan.c
>> b/drivers/mmc/host/sdhci-of-arasan.c
>> index 533e2bcb10bc..3ff1711077c2 100644
>> --- a/drivers/mmc/host/sdhci-of-arasan.c
>> +++ b/drivers/mmc/host/sdhci-of-arasan.c
>> @@ -35,11 +35,13 @@
>> /**
>> * struct sdhci_arasan_data
>> * @clk_ahb: Pointer to the AHB clock
>> - * @phy: Pointer to the generic phy
>> + * @phy: Pointer to the generic phy
>> + * @phy_on: True if the PHY is turned on.
>> */
>> struct sdhci_arasan_data {
>> struct clk *clk_ahb;
>> struct phy *phy;
>> + bool phy_on;
>> };
>>
>> static unsigned int sdhci_arasan_get_timeout_clock(struct sdhci_host
>> *host)
>> @@ -61,12 +63,10 @@ static void sdhci_arasan_set_clock(struct sdhci_host
>> *host, unsigned int clock)
>> {
>> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> struct sdhci_arasan_data *sdhci_arasan =
>> sdhci_pltfm_priv(pltfm_host);
>> - bool ctrl_phy = false;
>>
>> - if (clock > MMC_HIGH_52_MAX_DTR && (!IS_ERR(sdhci_arasan->phy)))
>> - ctrl_phy = true;
>> + if (sdhci_arasan->phy_on && !IS_ERR(sdhci_arasan->phy)) {
>> + sdhci_arasan->phy_on = false;
>>
>> - if (ctrl_phy) {
>> spin_unlock_irq(&host->lock);
>> phy_power_off(sdhci_arasan->phy);
>> spin_lock_irq(&host->lock);
>> @@ -74,7 +74,9 @@ static void sdhci_arasan_set_clock(struct sdhci_host
>> *host, unsigned int clock)
>>
>> sdhci_set_clock(host, clock);
>>
>> - if (ctrl_phy) {
>> + if (host->mmc->actual_clock && !IS_ERR(sdhci_arasan->phy)) {
>> + sdhci_arasan->phy_on = true;
>> +
>> spin_unlock_irq(&host->lock);
>> phy_power_on(sdhci_arasan->phy);
>> spin_lock_irq(&host->lock);
>> @@ -257,12 +259,6 @@ static int sdhci_arasan_probe(struct platform_device
>> *pdev)
>> goto clk_disable_all;
>> }
>>
>> - ret = phy_power_on(sdhci_arasan->phy);
>> - if (ret < 0) {
>> - dev_err(&pdev->dev, "phy_power_on err.\n");
>> - goto err_phy_power;
>> - }
>> -
>
>
> Because there is too much dependency between phy and controller, so
> previous solution is to setup clk by firmware. The same case for
> suspend and resume.
>
> Look really good to do it more legit.
Thanks! I don't see a Reviewed-by tag so I'm not adding it. If you'd
like your tag added, please let me know and I will add it if I send
out another version.
-Doug
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
