On 09/06/16 10:00, Kevin Tsai wrote:
> Added Vishay Capella CM36672 Proximity Sensor IIO driver. Support both
> ACPI and Device Tree.
>
> Signed-off-by: Kevin Tsai <capellamicro@xxxxxxxxx>
Few additional bits from me.
Thanks,
Jonathan
> ---
> V2:
> Thanks commends from Peter Meerwald-Stadler, Jonathan Cameron, and Linux
> Walleij. Updated for the following:
> - Remove unused defines.
> - Rewrite event registration.
> - Remove direct register values in the device tree.
> - Rewrite by regmap API.
> - Remove irq module parameter.
> - Correct cm36672_remove().
>
> .../devicetree/bindings/iio/light/cm36672.txt | 37 +
> MAINTAINERS | 4 +-
> drivers/iio/light/Kconfig | 11 +
> drivers/iio/light/Makefile | 1 +
> drivers/iio/light/cm36672.c | 820 +++++++++++++++++++++
> 5 files changed, 871 insertions(+), 2 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/iio/light/cm36672.txt
> create mode 100644 drivers/iio/light/cm36672.c
>
> diff --git a/Documentation/devicetree/bindings/iio/light/cm36672.txt b/Documentation/devicetree/bindings/iio/light/cm36672.txt
> new file mode 100644
> index 0000000..9681d2c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/light/cm36672.txt
> @@ -0,0 +1,37 @@
> +* Vishay Capella CM36672 I2C Proximity sensor
> +
> +Required properties:
> +- compatible: must be capella,cm36672"
> +- reg: the I2C slave address, usually 0x60
> +- interrupts: interrupt mapping for GPIO IRQ
> +
> +Optional properties:
> +- interrupt-parent: interrupt controller
> +- interrupts: interrupt mapping for GPIO IRQ
> +- cm36672,prx_led_current: LED current, must be one of the following values:
> + - 0: 50mA
> + - 1: 75mA
> + - 2: 100mA
> + - 3: 120mA
> + - 4: 140mA
> + - 5: 160mA
> + - 6: 180mA
> + - 7: 200mA
Use actual values and look them up in teh driver.
> +- cm36672,prx_hd: width of proximity sensor output data, must be one of the
> + following values:
> + - 0: 12-bit
> + - 1: 16-bit
Again, actual values please. Always nice if a binding is readable without
looking at the docs.
> +
> +Example:
> +
> + cm36672@60 {
> + compatible = "capella,cm36672";
> + reg = <0x60>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <30 0>;
> +
> + /* cm36672-specific properties */
> + cm36672,prx_led_current = <2>;
> + cm36672,prx_hd = <1>;
> + };
> +
> diff --git a/MAINTAINERS b/MAINTAINERS
> index ed42cb6..9618af4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2822,10 +2822,10 @@ F: security/commoncap.c
> F: kernel/capability.c
>
> CAPELLA MICROSYSTEMS LIGHT SENSOR DRIVER
> -M: Kevin Tsai <ktsai@xxxxxxxxxxxxxxxx>
> +M: Kevin Tsai <capellamicro@xxxxxxxxx>
> S: Maintained
> F: drivers/iio/light/cm*
> -F: Documentation/devicetree/bindings/i2c/trivial-devices.txt
> +F: Documentation/devicetree/bindings/iio/light/cm*
>
> CAVIUM LIQUIDIO NETWORK DRIVER
> M: Derek Chickles <derek.chickles@xxxxxxxxxxxxxxxxxx>
> diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
> index 7c566f5..cb5052a 100644
> --- a/drivers/iio/light/Kconfig
> +++ b/drivers/iio/light/Kconfig
> @@ -127,6 +127,17 @@ config CM36651
> To compile this driver as a module, choose M here:
> the module will be called cm36651.
>
> +config CM36672
> + depends on I2C
> + tristate "CM36672 driver"
> + help
> + Say Y here if you use cm36672.
> + This option enables proximity sensors using Vishay
> + Capella cm36672 device driver.
> +
> + To compile this driver as a module, choose M here:
> + the module will be called cm36672.
> +
> config GP2AP020A00F
> tristate "Sharp GP2AP020A00F Proximity/ALS sensor"
> depends on I2C
> diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile
> index 6f2a3c6..b155425 100644
> --- a/drivers/iio/light/Makefile
> +++ b/drivers/iio/light/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_CM32181) += cm32181.o
> obj-$(CONFIG_CM3232) += cm3232.o
> obj-$(CONFIG_CM3323) += cm3323.o
> obj-$(CONFIG_CM36651) += cm36651.o
> +obj-$(CONFIG_CM36672) += cm36672.o
> obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o
> obj-$(CONFIG_HID_SENSOR_ALS) += hid-sensor-als.o
> obj-$(CONFIG_HID_SENSOR_PROX) += hid-sensor-prox.o
> diff --git a/drivers/iio/light/cm36672.c b/drivers/iio/light/cm36672.c
> new file mode 100644
> index 0000000..975629f
> --- /dev/null
> +++ b/drivers/iio/light/cm36672.c
> @@ -0,0 +1,820 @@
> +/*
> + * CM36672 Proximity Sensor
> + *
> + * Copyright (C) 2014-2016 Vishay Capella
> + * Author: Kevin Tsai <capellamicro@xxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2, as published
> + * by the Free Software Foundation.
> + *
> + * IIO driver for CM36672 (7-bit I2C slave address 0x60).
> + */
> +#include <linux/kernel.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/interrupt.h>
> +#include <linux/regmap.h>
> +#include <linux/gpio.h>
> +
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +#include <linux/iio/events.h>
> +
> +#ifdef CONFIG_ACPI
> +#include <linux/acpi.h>
> +#endif
> +
> +#define CM36672_DRIVER_NAME "cm36672"
> +#define CM36672_REGMAP_NAME "cm36672_regmap"
No point in having this define, just put it inline. Also
the regmap bit is rather redundant ;)
> +
> +/* Sensor registers */
> +#define CM36672_ADDR_PRX_CONF 0x03
> +#define CM36672_ADDR_PRX_CONF3 0x04
> +#define CM36672_ADDR_PRX_THDL 0x06
> +#define CM36672_ADDR_PRX_THDH 0x07
> +#define CM36672_REGS_NUM 0x08
> +/* Read only registers */
> +#define CM36672_ADDR_PRX 0x08
> +#define CM36672_ADDR_STATUS 0x0B
> +
> +/* PRX_CONF */
> +#define CM36672_PRX_HD_SHIFT 11
> +#define CM36672_PRX_HD (1 << CM36672_PRX_HD_SHIFT)
> +
> +/* PRX_CONF: interrupt */
> +#define CM36672_PRX_INT_THDH BIT(8)
> +#define CM36672_PRX_INT_THDL BIT(9)
> +#define CM36672_PRX_INT_MASK (CM36672_PRX_INT_THDH | \
> + CM36672_PRX_INT_THDL)
> +
> +/* PRX_CONF: persistence */
> +#define CM36672_PRX_PERS_MASK (BIT(4) | BIT(5))
> +#define CM36672_PRX_PERS_SHIFT 4
> +#define CM36672_PRX_PERS_DISABLE 0
> +#define CM36672_PRX_PERS_2 (1 << CM36672_PRX_PERS_SHIFT)
> +#define CM36672_PRX_PERS_3 (2 << CM36672_PRX_PERS_SHIFT)
> +#define CM36672_PRX_PERS_4 (3 << CM36672_PRX_PERS_SHIFT)
> +
> +/* PRX_CONF: integration time */
> +#define CM36672_PRX_IT_MASK (BIT(1) | BIT(2) | BIT(3))
> +#define CM36672_PRX_IT_SHIFT 1
> +#define CM36672_PRX_IT_1T 0
> +#define CM36672_PRX_IT_1_5T (1 << CM36672_PRX_IT_SHIFT)
> +#define CM36672_PRX_IT_2T (2 << CM36672_PRX_IT_SHIFT)
> +#define CM36672_PRX_IT_2_5T (3 << CM36672_PRX_IT_SHIFT)
> +#define CM36672_PRX_IT_3T (4 << CM36672_PRX_IT_SHIFT)
> +#define CM36672_PRX_IT_3_5T (5 << CM36672_PRX_IT_SHIFT)
> +#define CM36672_PRX_IT_4T (6 << CM36672_PRX_IT_SHIFT)
> +#define CM36672_PRX_IT_8T (7 << CM36672_PRX_IT_SHIFT)
> +
> +/* PRX_CONF3 */
> +#define CM36672_PRX_LED_I_MASK (BIT(8) | BIT(9) | BIT(10))
> +#define CM36672_PRX_LED_I_SHIFT 8
> +#define CM36672_PRX_LED_I_50MA 0
> +#define CM36672_PRX_LED_I_75MA (1 << CM36672_PRX_LED_I_SHIFT)
> +#define CM36672_PRX_LED_I_100MA (2 << CM36672_PRX_LED_I_SHIFT)
> +#define CM36672_PRX_LED_I_120MA (3 << CM36672_PRX_LED_I_SHIFT)
> +#define CM36672_PRX_LED_I_140MA (4 << CM36672_PRX_LED_I_SHIFT)
> +#define CM36672_PRX_LED_I_160MA (5 << CM36672_PRX_LED_I_SHIFT)
> +#define CM36672_PRX_LED_I_180MA (6 << CM36672_PRX_LED_I_SHIFT)
> +#define CM36672_PRX_LED_I_200MA (7 << CM36672_PRX_LED_I_SHIFT)
> +
> +/* INT_FLAG */
> +#define CM36672_INT_PRX_CLOSE BIT(9)
> +#define CM36672_INT_PRX_AWAY BIT(8)
> +
> +struct cm36672_it_scale {
> + u8 it;
> + int val;
> + int val2;
> +};
> +
> +static const struct cm36672_it_scale cm36672_prx_it_scales[] = {
> + {0, 0, 100}, /* 0.00010 */
> + {1, 0, 150}, /* 0.00015 */
> + {2, 0, 200}, /* 0.00020 */
> + {3, 0, 250}, /* 0.00025 */
> + {4, 0, 300}, /* 0.00030 */
> + {5, 0, 350}, /* 0.00035 */
> + {6, 0, 400}, /* 0.00040 */
> + {7, 0, 800}, /* 0.00080 */
> +};
> +
> +#define CM36672_PRX_INT_TIME_AVAIL \
> + "0.000100 0.000150 0.000200 0.000250 " \
> + "0.000300 0.000350 0.000400 0.000800"
> +
> +static const u16 cm36672_regs_default[] = {
At very least, use an enum for the registers, and then name the elements
here.
[REGISTER_OF_MAGIC] = 0x0001,
etc.
> + 0x0001,
> + 0x0000,
> + 0x0000,
> + CM36672_PRX_INT_THDH | CM36672_PRX_INT_THDL |
> + CM36672_PRX_IT_2T | CM36672_PRX_PERS_3,
> + CM36672_PRX_LED_I_100MA,
> + 0x0000,
> + 0x0005,
> + 0x000A,
> +};
> +
> +struct cm36672_chip {
> + const struct cm36672_platform_data *pdata;
> + struct i2c_client *client;
> + struct mutex lock;
> +
> + /* regmap fields */
> + struct regmap *regmap;
> + struct regmap_field *reg_prx_int_hi;
> + struct regmap_field *reg_prx_int_lo;
> + struct regmap_field *reg_prx_it;
> +
> + u16 regs[CM36672_REGS_NUM];
> +};
> +
> +static const struct reg_field cm36672_reg_field_prx_int_hi =
> + REG_FIELD(CM36672_ADDR_PRX_CONF, 8, 8);
> +static const struct reg_field cm36672_reg_field_prx_int_lo =
> + REG_FIELD(CM36672_ADDR_PRX_CONF, 9, 9);
> +static const struct reg_field cm36672_reg_field_prx_it =
> + REG_FIELD(CM36672_ADDR_PRX_CONF, 1, 3);
> +
> +#ifdef CONFIG_OF
> +static void cm36672_mod_u16(u16 *reg, u16 mask, u8 shift, u16 val)
> +{
> + *reg &= ~mask;
> + *reg |= (u16)(val << shift);
> +}
> +
> +static void cm36672_parse_dt(struct cm36672_chip *chip)
> +{
> + struct device_node *dn = chip->client->dev.of_node;
> + u32 temp_val;
> +
> + if (!of_property_read_u32(dn, "cm36672,prx_led_current",
> + &temp_val))
> + cm36672_mod_u16(&chip->regs[CM36672_ADDR_PRX_CONF3],
> + CM36672_PRX_LED_I_MASK,
> + CM36672_PRX_LED_I_SHIFT,
> + (u16)temp_val);
> +
> + if (!of_property_read_u32(dn, "cm36672,prx_hd", &temp_val))
> + cm36672_mod_u16(&chip->regs[CM36672_ADDR_PRX_CONF],
> + CM36672_PRX_HD, CM36672_PRX_HD_SHIFT,
> + (u16)temp_val);
> +}
> +#endif
> +
> +#ifdef CONFIG_ACPI
> +/**
> + * cm36672_acpi_get_cpm_info() - Get CPM object from ACPI
> + * @client: pointer of struct i2c_client.
> + * @obj_name: pointer of ACPI object name.
> + * @count: maximum size of return array.
> + * @vals: pointer of array for return elements.
> + *
> + * Convert ACPI CPM table to array. Special thanks to Srinivas Pandruvada's
> + * help to implement this routine.
> + *
> + * Return: -ENODEV for fail. Otherwise the number of elements.
> + */
> +static int cm36672_acpi_get_cpm_info(struct i2c_client *client, char *obj_name,
> + int count, u64 *vals)
> +{
> + acpi_handle handle;
> + struct acpi_buffer buffer = {ACPI_ALLOCATE_BUFFER, NULL};
> + int i;
> + acpi_status status;
> + union acpi_object *cpm;
> +
> + handle = ACPI_HANDLE(&client->dev);
> + if (!handle)
> + return -ENODEV;
> +
> + status = acpi_evaluate_object(handle, obj_name, NULL, &buffer);
> + if (ACPI_FAILURE(status)) {
> + dev_err(&client->dev, "object %s not found\n", obj_name);
> + return -ENODEV;
> + }
> +
> + cpm = buffer.pointer;
> + for (i = 0; i < cpm->package.count && i < count; ++i) {
> + union acpi_object *elem;
> +
> + elem = &(cpm->package.elements[i]);
> + vals[i] = elem->integer.value;
> + }
> +
> + kfree(buffer.pointer);
This is particularly ugly from the ACPI side of things given there
is no explicit indication in the evaluate_object above that it
is doing any allocations... Ah well, if that's the way it is such
is life I guess.
> +
> + return i;
> +}
> +
> +static void cm36672_parse_acpi(struct cm36672_chip *chip)
> +{
> + struct i2c_client *client = chip->client;
> + int cpm_elem_count, i;
> + u64 cpm_elems[20];
> +
> + cpm_elem_count = cm36672_acpi_get_cpm_info(client, "CPM0",
> + ARRAY_SIZE(cpm_elems), cpm_elems);
> +
> + if (cpm_elem_count > 0) {
> + int header_num = 3;
> + int regs_bmp = cpm_elems[2];
> + int reg_num = cpm_elem_count - header_num;
> +
> + if (reg_num > CM36672_REGS_NUM)
> + reg_num = CM36672_REGS_NUM;
> + for (i = 0; i < reg_num; i++)
> + if (regs_bmp & (1 << i))
> + chip->regs[i] = cpm_elems[header_num + i];
> + }
> +}
> +
> +#endif
> +
> +static int cm36672_regfield_init(struct cm36672_chip *chip)
> +{
> + struct device *dev = &chip->client->dev;
> + struct regmap *regmap = chip->regmap;
> +
> + chip->reg_prx_int_lo = devm_regmap_field_alloc(dev, regmap,
> + cm36672_reg_field_prx_int_lo);
> + if (IS_ERR(chip->reg_prx_int_lo)) {
> + dev_err(dev, "%s: reg_prx_int_lo init failed\n", __func__);
> + return PTR_ERR(chip->reg_prx_int_lo);
> + }
> +
> + chip->reg_prx_int_hi = devm_regmap_field_alloc(dev, regmap,
> + cm36672_reg_field_prx_int_hi);
> + if (IS_ERR(chip->reg_prx_int_hi)) {
> + dev_err(dev, "%s: reg_prx_int_hi init failed\n", __func__);
> + return PTR_ERR(chip->reg_prx_int_hi);
> + }
> +
> + chip->reg_prx_it = devm_regmap_field_alloc(dev, regmap,
> + cm36672_reg_field_prx_it);
> + if (IS_ERR(chip->reg_prx_it)) {
> + dev_err(dev, "%s: reg_prx_it init failed\n", __func__);
> + return PTR_ERR(chip->reg_prx_it);
> + }
As mentioned in the other branch of the thread, a small amount of
reorganization and this can be a single loop. I'd not bother
two much with the error messages here as it's very unlikely to ever
fail...
> +
> + return 0;
> +}
> +
> +/**
> + * cm36672_setup_reg() - Initialize sensor to default values.
> + * @chip: pointer of struct cm36672_chip
> + *
> + * Return: 0 for success; otherwise an error code.
> + */
> +static int cm36672_setup_reg(struct cm36672_chip *chip)
> +{
> + int i, reg, ret;
> + u16 prx_conf;
> +
> + memcpy((char *)&chip->regs, (char *)&cm36672_regs_default,
> + sizeof(cm36672_regs_default));
> +
> +#ifdef CONFIG_OF
> + if (chip->client->dev.of_node)
> + cm36672_parse_dt(chip);
> +#endif
> +
> +#ifdef CONFIG_ACPI
> + if (ACPI_HANDLE(&chip->client->dev))
> + cm36672_parse_acpi(chip);
> +#endif
> +
> + /* Store regs[CM36672_ADDR_PRX_CONF] */
> + prx_conf = chip->regs[CM36672_ADDR_PRX_CONF];
> +
> + /* Disable INT when initialize registers */
> + chip->regs[CM36672_ADDR_PRX_CONF] &= ~CM36672_PRX_INT_THDH;
> + chip->regs[CM36672_ADDR_PRX_CONF] &= ~CM36672_PRX_INT_THDL;
> +
> + for (i = 0; i < CM36672_REGS_NUM; i++) {
> + ret = regmap_write(chip->regmap, i, chip->regs[i]);
> + if (ret < 0)
> + return ret;
> + }
> +
> + /* Restore regs[CM36672_ADDR_PRX_CONF] */
> + chip->regs[CM36672_ADDR_PRX_CONF] = prx_conf;
> +
> + /* Force to clear flags */
> + ret = regmap_read(chip->regmap, CM36672_ADDR_STATUS, ®);
> + if (ret < 0) {
> + dev_err(&chip->client->dev,
> + "%s: Failed to read Status register, err= %d\n",
> + __func__, ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * cm36672_irq_handler() - Interrupt handling routine.
> + * @irq: irq number
> + * @private: pointer of void
> + *
> + * Return: IRQ_HANDLED.
> + */
> +static irqreturn_t cm36672_irq_handler(int irq, void *private)
> +{
> + struct iio_dev *indio_dev = private;
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + s64 timestamp = iio_get_time_ns();
> + int ret, status;
> +
> + ret = regmap_read(chip->regmap, CM36672_ADDR_STATUS, &status);
> + if (ret < 0)
> + return IRQ_HANDLED;
> +
> + if (status & CM36672_INT_PRX_CLOSE)
> + iio_push_event(indio_dev,
> + IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, 0,
> + IIO_EV_TYPE_THRESH,
> + IIO_EV_DIR_RISING),
> + timestamp);
> +
> + if (status & CM36672_INT_PRX_AWAY)
> + iio_push_event(indio_dev,
> + IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY, 0,
> + IIO_EV_TYPE_THRESH,
> + IIO_EV_DIR_FALLING),
> + timestamp);
> +
> + return IRQ_HANDLED;
> +}
> +
> +/**
> + * cm36672_read_prx_it() - Get the current proximity integration time.
> + * @chip: point of struct cm36672_chip
> + * @val: point of the integer part of integration time
> + * @val2: point of the micro part of integration time
> + *
> + * Return: IIO_VAL_INT_PLUS_MICRO for success; otherwise an error code.
> + */
> +static int cm36672_read_prx_it(struct cm36672_chip *chip, int *val, int *val2)
> +{
> + int ret, index;
> +
> + ret = regmap_field_read(chip->reg_prx_it, &index);
> + if (ret < 0)
> + return ret;
> +
> + if (index < 0 || index >= ARRAY_SIZE(cm36672_prx_it_scales))
> + return -EINVAL;
> +
> + *val = cm36672_prx_it_scales[index].val;
> + *val2 = cm36672_prx_it_scales[index].val2;
> +
> + return IIO_VAL_INT_PLUS_MICRO;
> +}
> +
> +/**
> + * cm36672_write_prx_it() - Set the proximity integration time.
> + * @chip: point of struct cm36672_chip
> + * @val: the integer part of integration time
> + * @val2: the micro part of integration time
> + *
> + * Return: 0 for success; otherwise an error code.
> + */
> +static int cm36672_write_prx_it(struct cm36672_chip *chip, int val, int val2)
> +{
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(cm36672_prx_it_scales); i++)
> + if (val == cm36672_prx_it_scales[i].val &&
> + val2 == cm36672_prx_it_scales[i].val2)
> + return regmap_field_write(chip->reg_prx_it, i);
> +
> + return -EINVAL;
> +}
> +
> +/**
> + * cm36672_prx_read() - Read from proximity sensor.
> + * @indio_dev: point of struct iio_dev
> + * @chan: point of struct iio_chan_spec
> + * @val: point of integer
This is documenting the types, not what they are. Fix that orjust
drop the documentation as it is not informative.
> + * @val2: point of integer
> + * @mask: iio_chan_info_enum
> + *
> + * Return: IIO_VAL type for success; otherwise an error code.
> + */
> +static int cm36672_prx_read(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + int ret;
> +
> + if (chan->type != IIO_PROXIMITY)
> + return -EINVAL;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_INT_TIME:
> + return cm36672_read_prx_it(chip, val, val2);
> + case IIO_CHAN_INFO_RAW:
> + ret = regmap_read(chip->regmap, CM36672_ADDR_PRX, val);
> + if (ret < 0)
> + return ret;
> + return IIO_VAL_INT;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +/**
> + * cm36672_prx_write() - Write to proximity sensor.
Does the prx part add any information? If this is just a proximity
sensor I'd drop it throughout.
> + * @indio_dev: point of struct iio_dev
> + * @chan: point of struct iio_chan_spec
> + * @val: integer for integer part
> + * @val2: integer for micro part
> + * @mask: iio_chan_info_enum
> + *
> + * Return: Equal or great than 0 for success; otherwise an error code.
> + */
> +static int cm36672_prx_write(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int val, int val2, long mask)
> +{
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_INT_TIME:
> + return cm36672_write_prx_it(chip, val, val2);
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int cm36672_read_event(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + enum iio_event_info info,
> + int *val, int *val2)
> +{
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + int ret = -EINVAL;
> +
> + if (info != IIO_EV_INFO_VALUE)
> + return -EINVAL;
> +
> + if (chan->type == IIO_PROXIMITY) {
> + *val2 = 0;
> + if (dir == IIO_EV_DIR_RISING)
> + ret = regmap_read(chip->regmap, CM36672_ADDR_PRX_THDH,
> + val);
> + else if (dir == IIO_EV_DIR_FALLING)
> + ret = regmap_read(chip->regmap, CM36672_ADDR_PRX_THDL,
> + val);
> + }
> +
> + if (ret < 0)
> + return ret;
> +
> + return IIO_VAL_INT;
> +}
> +
> +static int cm36672_write_event(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + enum iio_event_info info,
> + int val, int val2)
> +{
> + int reg, ret = 0;
> + int value, max;
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> +
> + if (info != IIO_EV_INFO_VALUE)
> + return -EINVAL;
> +
> + if (chan->type == IIO_PROXIMITY) {
> + ret = regmap_read(chip->regmap, CM36672_ADDR_PRX_CONF, &value);
> + max = (value & CM36672_PRX_HD) ? 65535:4095;
> + if (val < 0 || val > max)
> + return -EINVAL;
> + if (dir == IIO_EV_DIR_RISING)
> + reg = CM36672_ADDR_PRX_THDH;
> + else if (dir == IIO_EV_DIR_FALLING)
> + reg = CM36672_ADDR_PRX_THDL;
> + else
> + return -EINVAL;
> +
> + ret = regmap_write(chip->regmap, reg, val);
> + if (ret < 0)
> + return ret;
> + } else
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static int cm36672_read_event_config(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir)
> +{
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + int ret, state;
> +
> + if (chan->type == IIO_PROXIMITY) {
> + if (dir == IIO_EV_DIR_RISING)
> + ret = regmap_field_read(chip->reg_prx_int_hi, &state);
> + else if (dir == IIO_EV_DIR_FALLING)
> + ret = regmap_field_read(chip->reg_prx_int_lo, &state);
> + else
> + return -EINVAL;
> +
> + if (ret)
> + return ret;
> +
> + return state;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int cm36672_write_event_config(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + int state)
> +{
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + int ret;
> +
> + if (chan->type == IIO_PROXIMITY) {
> + if (dir == IIO_EV_DIR_RISING)
> + ret = regmap_field_write(chip->reg_prx_int_hi, state);
> + else if (dir == IIO_EV_DIR_FALLING)
> + ret = regmap_field_write(chip->reg_prx_int_lo, state);
> + else
> + return -EINVAL;
> +
> + if (ret)
> + return ret;
> +
> + return 0;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static const struct iio_event_spec cm36672_prx_event_spec[] = {
> + {
> + .type = IIO_EV_TYPE_THRESH,
> + .dir = IIO_EV_DIR_RISING,
> + .mask_separate = BIT(IIO_EV_INFO_VALUE) |
> + BIT(IIO_EV_INFO_ENABLE),
> + },
> + {
> + .type = IIO_EV_TYPE_THRESH,
> + .dir = IIO_EV_DIR_FALLING,
> + .mask_separate = BIT(IIO_EV_INFO_VALUE) |
> + BIT(IIO_EV_INFO_ENABLE),
> + },
> +};
> +
> +static const struct iio_chan_spec cm36672_channels[] = {
> + {
> + .type = IIO_PROXIMITY,
> + .info_mask_separate =
> + BIT(IIO_CHAN_INFO_RAW),
> + BIT(IIO_CHAN_INFO_INT_TIME),
> + .channel = 0,
> + .indexed = 0,
> + .scan_index = -1,
> + .event_spec = cm36672_prx_event_spec,
> + .num_event_specs = ARRAY_SIZE(cm36672_prx_event_spec),
> + },
> +};
> +
> +static bool cm36672_is_writeable_reg(struct device *dev, unsigned int reg)
> +{
> + if (reg <= CM36672_ADDR_PRX_THDH)
> + return true;
> + return false;
> +}
> +
> +static IIO_CONST_ATTR(in_proximity_integration_time_available,
> + CM36672_PRX_INT_TIME_AVAIL);
> +
> +static struct attribute *cm36672_attributes[] = {
> + &iio_const_attr_in_proximity_integration_time_available.dev_attr.attr,
> + NULL,
> +};
> +
> +static const struct attribute_group cm36672_attribute_group = {
> + .attrs = cm36672_attributes
> +};
> +
> +static const struct iio_info cm36672_info = {
> + .driver_module = THIS_MODULE,
> + .read_raw = &cm36672_prx_read,
> + .write_raw = &cm36672_prx_write,
> + .attrs = &cm36672_attribute_group,
> + .read_event_value = cm36672_read_event,
> + .write_event_value = cm36672_write_event,
> + .read_event_config = cm36672_read_event_config,
> + .write_event_config = cm36672_write_event_config,
> +};
> +
> +static const struct iio_info cm36672_info_no_irq = {
> + .driver_module = THIS_MODULE,
> + .read_raw = &cm36672_prx_read,
> + .write_raw = &cm36672_prx_write,
> + .attrs = &cm36672_attribute_group,
> +};
> +
> +static const struct regmap_config cm36672_regmap_config = {
> + .name = CM36672_REGMAP_NAME,
> + .reg_bits = 8,
> + .val_bits = 16,
> + .writeable_reg = cm36672_is_writeable_reg,
> + .use_single_rw = true,
> + .val_format_endian = REGMAP_ENDIAN_LITTLE,
> +};
> +
> +static int cm36672_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct cm36672_chip *chip;
> + struct iio_dev *indio_dev;
> + struct regmap *regmap;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + regmap = devm_regmap_init_i2c(client, &cm36672_regmap_config);
> + if (IS_ERR(regmap)) {
> + dev_err(&client->dev, "%s: regmap initialize failed\n",
> + __func__);
> + return PTR_ERR(regmap);
> + }
> +
> + chip = iio_priv(indio_dev);
> + i2c_set_clientdata(client, indio_dev);
> + chip->client = client;
> + chip->regmap = regmap;
> +
> + mutex_init(&chip->lock);
> + indio_dev->dev.parent = &client->dev;
> + indio_dev->channels = cm36672_channels;
> + indio_dev->num_channels = ARRAY_SIZE(cm36672_channels);
> + indio_dev->name = CM36672_DRIVER_NAME;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + ret = cm36672_regfield_init(chip);
> + if (ret) {
> + dev_err(&client->dev, "%s: regfield init failed\n", __func__);
> + return ret;
> + }
> +
> + ret = cm36672_setup_reg(chip);
> + if (ret) {
> + dev_err(&client->dev, "%s: register setup failed\n", __func__);
> + return ret;
> + }
> +
> + if (client->irq) {
> + indio_dev->info = &cm36672_info;
> +
> + ret = request_threaded_irq(client->irq, NULL,
> + cm36672_irq_handler,
> + IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> + "cm36672", indio_dev);
> + if (ret) {
> + dev_err(&client->dev,
> + "%s: request irq failed\n",
> + __func__);
> + return ret;
> + }
> +
> + /* Enable interrupt if default request*/
> + if (chip->regs[CM36672_ADDR_PRX_CONF] & CM36672_PRX_INT_MASK) {
> + ret = regmap_write(chip->regmap, CM36672_ADDR_PRX_CONF,
> + chip->regs[CM36672_ADDR_PRX_CONF]);
> + if (ret) {
You aren't unwinding the irq here. I'd suggest using a goto and
explicit error path in this code. Less error prone as the code evolves.
Also I'd expect the interrupt to be disabled in later errors and it
isn't... Rule of thumb, on error back out all stuff you've done before
it.
> + dev_err(&client->dev,
> + "%s: enable interrupt failed\n",
> + __func__);
> + return ret;
> + }
> + }
> + } else
> + indio_dev->info = &cm36672_info_no_irq;
> +
> + ret = iio_device_register(indio_dev);
> + if (ret) {
> + dev_err(&client->dev,
> + "%s: registering device failed\n",
> + __func__);
> + if (client->irq)
> + free_irq(client->irq, indio_dev);
> + }
> +
> + return 0;
> +}
> +
> +static int cm36672_remove(struct i2c_client *client)
> +{
> + struct iio_dev *indio_dev = i2c_get_clientdata(client);
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> +
> + iio_device_unregister(indio_dev);
> + regmap_update_bits(chip->regmap, CM36672_ADDR_PRX_CONF, 1, 1);
> + if (client->irq)
> + free_irq(client->irq, indio_dev);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id cm36672_id[] = {
> + { "cm36672", 0 },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, cm36672_id);
> +
> +static const struct of_device_id cm36672_of_match[] = {
> + { .compatible = "capella,cm36672" },
> + { }
> +};
> +
> +#ifdef CONFIG_ACPI
> +static const struct acpi_device_id cm36672_acpi_match[] = {
> + { "CPLM6672", 0},
> + {},
> +};
> +
> +MODULE_DEVICE_TABLE(acpi, cm36672_acpi_match);
> +#endif
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int cm36672_suspend(struct device *dev)
> +{
> + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + struct i2c_client *client = chip->client;
> + int i, ret;
> +
> + for (i = 0; i < CM36672_REGS_NUM; i++) {
> + ret = i2c_smbus_read_word_data(client, i);
> + if (ret < 0)
> + return ret;
> + chip->regs[i] = ret;
> + }
> +
> + return regmap_update_bits(chip->regmap, CM36672_ADDR_PRX_CONF, 1, 1);
> +}
> +
> +static int cm36672_resume(struct device *dev)
> +{
> + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
> + struct cm36672_chip *chip = iio_priv(indio_dev);
> + struct i2c_client *client = chip->client;
> + int i, ret;
> +
> + for (i = 0; i < CM36672_REGS_NUM; i++) {
> + ret = i2c_smbus_write_word_data(client, i, chip->regs[i]);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return regmap_update_bits(chip->regmap, CM36672_ADDR_PRX_CONF, 1, 0);
> +}
> +
> +static const struct dev_pm_ops cm36672_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(cm36672_suspend, cm36672_resume)};
> +#endif
> +
> +static struct i2c_driver cm36672_driver = {
> + .driver = {
> + .name = CM36672_DRIVER_NAME,
> + .owner = THIS_MODULE,
> + .of_match_table = cm36672_of_match,
> +#ifdef CONFIG_ACPI
> + .acpi_match_table = ACPI_PTR(cm36672_acpi_match),
> +#endif
> +#ifdef CONFIG_PM_SLEEP
> + .pm = &cm36672_pm_ops,
> +#endif
> + },
> + .id_table = cm36672_id,
> + .probe = cm36672_probe,
> + .remove = cm36672_remove,
> +};
> +
> +module_i2c_driver(cm36672_driver);
> +
> +MODULE_AUTHOR("Kevin Tsai <capellamicro@xxxxxxxxx>");
> +MODULE_DESCRIPTION("CM36672 proximity sensor driver");
> +MODULE_LICENSE("GPL v2");
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
