On 06/06/16 20:15, Iyappan Subramanian wrote:
This patch looks for CONFIG_MDIO_XGENE and based on phy-handle DT/ACPI
fields, sets the mdio_driver flag. The rest of the driver uses the
I'm a bit confused, you introduced mdio_driver flag already in patch 1.
this flag for any MDIO management, in the case of backward compatibility.
Also, some code clean up done around mdio configuration/remove.
IMHO code clean up should be part of a different patch.
Signed-off-by: Iyappan Subramanian <isubramanian@xxxxxxx>
Tested-by: Fushen Chen <fchen@xxxxxxx>
Tested-by: Toan Le <toanle@xxxxxxx>
Tested-by: Matthias Brugger <mbrugger@xxxxxxxx>
---
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c | 60 +++-----
drivers/net/ethernet/apm/xgene/xgene_enet_main.c | 165 +++++++++++++++-------
drivers/net/ethernet/apm/xgene/xgene_enet_main.h | 2 +
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c | 13 +-
4 files changed, 148 insertions(+), 92 deletions(-)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
index 5d6d14b..38d6ee4 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
@@ -476,9 +476,13 @@ static void xgene_gmac_reset(struct xgene_enet_pdata *pdata)
static void xgene_enet_configure_clock(struct xgene_enet_pdata *pdata)
{
struct device *dev = &pdata->pdev->dev;
+ struct clk *parent;
if (dev->of_node) {
- struct clk *parent = clk_get_parent(pdata->clk);
+ if (IS_ERR(pdata->clk))
+ return;
+
+ parent = clk_get_parent(pdata->clk);
switch (pdata->phy_speed) {
case SPEED_10:
@@ -572,6 +576,9 @@ static void xgene_gmac_init(struct xgene_enet_pdata *pdata)
{
u32 value;
+ if (!pdata->mdio_driver)
+ xgene_gmac_reset(pdata);
+
xgene_gmac_set_speed(pdata);
xgene_gmac_set_mac_addr(pdata);
@@ -677,7 +684,14 @@ static int xgene_enet_reset(struct xgene_enet_pdata *pdata)
if (!xgene_ring_mgr_init(pdata))
return -ENODEV;
- xgene_enet_ecc_init(pdata);
+ if (!pdata->mdio_driver) {
+ if (!IS_ERR(pdata->clk)) {
+ clk_prepare_enable(pdata->clk);
+ clk_disable_unprepare(pdata->clk);
+ clk_prepare_enable(pdata->clk);
+ xgene_enet_ecc_init(pdata);
+ }
+ }
In the first patch you add xgene_enet_ecc_init and delete the clock
handling. Here you do it the other way round. And in patch 5 you put
both after calling xgene_enet_config_ring_if_assoc.
Are these changes needed like this in every patch?
xgene_enet_config_ring_if_assoc(pdata);
return 0;
@@ -800,27 +814,9 @@ static int xgene_mdiobus_register(struct xgene_enet_pdata *pdata,
struct mii_bus *mdio)
{
struct device *dev = &pdata->pdev->dev;
- struct device_node *mdio_np = NULL;
- struct device_node *child_np;
- u32 phyid;
if (dev->of_node) {
- for_each_child_of_node(dev->of_node, child_np) {
- if (of_device_is_compatible(child_np,
- "apm,xgene-mdio")) {
- mdio_np = child_np;
- break;
- }
- }
-
- if (!mdio_np) {
- mdiobus_free(mdio);
- return 0;
- }
-
- pdata->mdio_driver = false;
-
- return of_mdiobus_register(mdio, mdio_np);
+ return of_mdiobus_register(mdio, pdata->mdio_np);
} else {
#ifdef CONFIG_ACPI
struct phy_device *phy;
@@ -839,13 +835,7 @@ static int xgene_mdiobus_register(struct xgene_enet_pdata *pdata,
if (ret)
return ret;
- ret = device_property_read_u32(dev, "phy-channel", &phyid);
- if (ret)
- ret = device_property_read_u32(dev, "phy-addr", &phyid);
- if (ret)
- return -EINVAL;
-
- phy = get_phy_device(mdio, phyid, false);
+ phy = get_phy_device(mdio, pdata->phy_id, false);
if (IS_ERR(phy))
return -EIO;
@@ -858,6 +848,8 @@ static int xgene_mdiobus_register(struct xgene_enet_pdata *pdata,
return ret;
#endif
}
+
+ return 0;
}
int xgene_enet_mdio_config(struct xgene_enet_pdata *pdata)
@@ -885,10 +877,6 @@ int xgene_enet_mdio_config(struct xgene_enet_pdata *pdata)
if (mdio_bus->state == MDIOBUS_REGISTERED)
mdiobus_unregister(pdata->mdio_bus);
mdiobus_free(mdio_bus);
- if (pdata->mdio_driver) {
- ret = xgene_enet_phy_connect(ndev);
- return 0;
- }
return ret;
}
pdata->mdio_bus = mdio_bus;
@@ -911,11 +899,9 @@ void xgene_enet_mdio_remove(struct xgene_enet_pdata *pdata)
if (pdata->phy_dev)
phy_disconnect(pdata->phy_dev);
- if (!pdata->mdio_driver) {
- mdiobus_unregister(pdata->mdio_bus);
- mdiobus_free(pdata->mdio_bus);
- pdata->mdio_bus = NULL;
- }
+ mdiobus_unregister(pdata->mdio_bus);
+ mdiobus_free(pdata->mdio_bus);
+ pdata->mdio_bus = NULL;
}
const struct xgene_mac_ops xgene_gmac_ops = {
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_main.c b/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
index d451e5d..c31ea56 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_main.c
@@ -1182,31 +1182,27 @@ static const struct net_device_ops xgene_ndev_ops = {
#ifdef CONFIG_ACPI
static void xgene_get_port_id_acpi(struct device *dev,
- struct xgene_enet_pdata *pdata)
+ struct xgene_enet_pdata *pdata)
A space slipped in which we don't need.
{
acpi_status status;
u64 temp;
status = acpi_evaluate_integer(ACPI_HANDLE(dev), "_SUN", NULL, &temp);
- if (ACPI_FAILURE(status)) {
+ if (ACPI_FAILURE(status))
pdata->port_id = 0;
- } else {
+ else
pdata->port_id = temp;
- }
-
- return;
}
#endif
-static void xgene_get_port_id_dt(struct device *dev, struct xgene_enet_pdata *pdata)
+static void xgene_get_port_id_dt(struct device *dev,
+ struct xgene_enet_pdata *pdata)
{
u32 id = 0;
of_property_read_u32(dev->of_node, "port-id", &id);
pdata->port_id = id & BIT(0);
-
- return;
}
static int xgene_get_tx_delay(struct xgene_enet_pdata *pdata)
@@ -1284,6 +1280,86 @@ static int xgene_enet_get_irqs(struct xgene_enet_pdata *pdata)
return 0;
}
+static int xgene_enet_check_phy_handle(struct xgene_enet_pdata *pdata)
+{
+ struct device *dev = &pdata->pdev->dev;
+ int ret, phy_id, phy_mode = pdata->phy_mode;
+ struct device_node *mdio_np = NULL;
+ const char *ph;
+#ifdef CONFIG_ACPI
+ struct acpi_reference_args args;
+ struct fwnode_handle *fw_node;
+#endif
+
+ if (!IS_ENABLED(CONFIG_MDIO_XGENE))
+ return 0;
Kconfig option is introduced in patch 3. So I suppose we should add at
least this lines to this patch. Or at least we should change the order
of the patches, to not introduce a check for a Kconfig option before it
is even present in the kernel. What do you think?
+
+ if (dev->of_node) {
+ ret = device_property_read_string(dev, "phy-handle", &ph);
+
+ if (phy_mode == PHY_INTERFACE_MODE_RGMII) {
+ if (ret) {
+ dev_err(dev, "Unable to get phy-handle\n");
+ return ret;
+ }
+
+ mdio_np = of_find_compatible_node(dev->of_node, NULL,
+ "apm,xgene-mdio");
+ if (!mdio_np)
+ pdata->mdio_driver = true;
+ else
+ pdata->mdio_np = mdio_np;
+ } else {
+ if (!ret)
+ pdata->mdio_driver = true;
+ }
+ } else {
+#ifdef CONFIG_ACPI
+ fw_node = acpi_fwnode_handle(ACPI_COMPANION(dev));
+ ret = acpi_node_get_property_reference(fw_node, "mboxes", 0,
+ &args);
+ if (!ACPI_FAILURE(ret)) {
+ pdata->mdio_driver = true;
+ pdata->phy_dev = args.adev->driver_data;
+ } else {
+ ret = device_property_read_u32(dev, "phy-channel",
+ &phy_id);
+ if (ret) {
+ ret = device_property_read_u32(dev, "phy-addr",
+ &phy_id);
+ }
+
+ if (!ret)
+ pdata->phy_id = phy_id;
+ }
+#endif
+ }
+
+ return 0;
+}
+
+static int xgene_enet_get_clk(struct xgene_enet_pdata *pdata)
+{
+ struct device *dev = &pdata->pdev->dev;
+
+ if (!dev->of_node)
+ return 0;
+
+ pdata->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(pdata->clk)) {
+ if (pdata->phy_mode == PHY_INTERFACE_MODE_RGMII) {
+ dev_err(dev, "Unable to get clock\n");
+ return -ENODEV;
+ } else {
+ /* Firmware may have set up the clock already. */
+ dev_info(dev, "clocks have been setup already\n");
AFAIK clk_get does not check if the bootloader has set up the clock. It
just gives you a reference to a clock that was defined in the clock
driver of your SOC. So for me this comment and dev_info make no sense.
Regards,
Matthias
+ pdata->clk = NULL;
+ }
+ }
+
+ return 0;
+}
+
static int xgene_enet_get_resources(struct xgene_enet_pdata *pdata)
{
struct platform_device *pdev;
@@ -1292,7 +1368,6 @@ static int xgene_enet_get_resources(struct xgene_enet_pdata *pdata)
struct resource *res;
void __iomem *base_addr;
u32 offset;
- const char *ph;
int ret = 0;
pdev = pdata->pdev;
@@ -1370,15 +1445,13 @@ static int xgene_enet_get_resources(struct xgene_enet_pdata *pdata)
if (ret)
return ret;
- ret = device_property_read_string(dev, "phy-handle", &ph);
- if (!ret)
- pdata->mdio_driver = true;
+ ret = xgene_enet_check_phy_handle(pdata);
+ if (ret)
+ return ret;
- pdata->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(pdata->clk)) {
- /* Firmware may have set up the clock already. */
- dev_info(dev, "clocks have been setup already\n");
- }
+ ret = xgene_enet_get_clk(pdata);
+ if (ret)
+ return ret;
if ((pdata->phy_mode != PHY_INTERFACE_MODE_XGMII) &&
(pdata->enet_id == XGENE_ENET1))
@@ -1434,8 +1507,6 @@ static int xgene_enet_init_hw(struct xgene_enet_pdata *pdata)
}
}
- dst_ring_num = xgene_enet_dst_ring_num(pdata->rx_ring[0]);
- buf_pool = pdata->rx_ring[0]->buf_pool;
if (pdata->phy_mode == PHY_INTERFACE_MODE_XGMII) {
/* Initialize and Enable PreClassifier Tree */
enet_cle->max_nodes = 512;
@@ -1451,9 +1522,12 @@ static int xgene_enet_init_hw(struct xgene_enet_pdata *pdata)
return ret;
}
} else {
+ dst_ring_num = xgene_enet_dst_ring_num(pdata->rx_ring[0]);
+ buf_pool = pdata->rx_ring[0]->buf_pool;
pdata->port_ops->cle_bypass(pdata, dst_ring_num, buf_pool->id);
}
+ pdata->phy_speed = SPEED_UNKNOWN;
pdata->mac_ops->init(pdata);
return ret;
@@ -1563,22 +1637,6 @@ static void xgene_enet_napi_add(struct xgene_enet_pdata *pdata)
}
}
-static void xgene_enet_napi_del(struct xgene_enet_pdata *pdata)
-{
- struct napi_struct *napi;
- int i;
-
- for (i = 0; i < pdata->rxq_cnt; i++) {
- napi = &pdata->rx_ring[i]->napi;
- netif_napi_del(napi);
- }
-
- for (i = 0; i < pdata->cq_cnt; i++) {
- napi = &pdata->tx_ring[i]->cp_ring->napi;
- netif_napi_del(napi);
- }
-}
-
static int xgene_enet_probe(struct platform_device *pdev)
{
struct net_device *ndev;
@@ -1609,8 +1667,7 @@ static int xgene_enet_probe(struct platform_device *pdev)
of_id = of_match_device(xgene_enet_of_match, &pdev->dev);
if (of_id) {
pdata->enet_id = (enum xgene_enet_id)of_id->data;
- }
- else {
+ } else {
#ifdef CONFIG_ACPI
const struct acpi_device_id *acpi_id;
enum xgene_enet_id enet_id;
@@ -1622,6 +1679,7 @@ static int xgene_enet_probe(struct platform_device *pdev)
}
#endif
}
+
if (!pdata->enet_id) {
free_netdev(ndev);
return -ENODEV;
@@ -1656,23 +1714,25 @@ static int xgene_enet_probe(struct platform_device *pdev)
goto err_netdev;
link_state = pdata->mac_ops->link_state;
- if (pdata->phy_mode == PHY_INTERFACE_MODE_RGMII) {
- ret = xgene_enet_mdio_config(pdata);
- if (ret)
- goto err_netdev;
- } else if (pdata->phy_mode == PHY_INTERFACE_MODE_SGMII) {
+ ret = 0;
+ if (pdata->phy_mode == PHY_INTERFACE_MODE_XGMII) {
+ INIT_DELAYED_WORK(&pdata->link_work, link_state);
+ } else {
if (pdata->mdio_driver)
ret = xgene_enet_phy_connect(ndev);
+ else if (pdata->phy_mode == PHY_INTERFACE_MODE_RGMII)
+ ret = xgene_enet_mdio_config(pdata);
else
INIT_DELAYED_WORK(&pdata->link_work, link_state);
- } else {
- INIT_DELAYED_WORK(&pdata->link_work, link_state);
}
+ if (ret)
+ goto err;
xgene_enet_napi_add(pdata);
return 0;
err_netdev:
- unregister_netdev(ndev);
+ if (ndev->reg_state == NETREG_REGISTERED)
+ unregister_netdev(ndev);
err:
free_netdev(ndev);
return ret;
@@ -1691,11 +1751,16 @@ static int xgene_enet_remove(struct platform_device *pdev)
mac_ops->rx_disable(pdata);
mac_ops->tx_disable(pdata);
- xgene_enet_napi_del(pdata);
- if (pdata->phy_mode == PHY_INTERFACE_MODE_RGMII)
- xgene_enet_mdio_remove(pdata);
- else if (pdata->phy_mode == PHY_INTERFACE_MODE_SGMII)
+ rtnl_lock();
+ if (netif_running(ndev))
+ dev_close(ndev);
+ rtnl_unlock();
+
+ if (pdata->mdio_driver)
xgene_enet_phy_disconnect(pdata);
+ else if (pdata->phy_mode == PHY_INTERFACE_MODE_RGMII)
+ xgene_enet_mdio_remove(pdata);
+
unregister_netdev(ndev);
xgene_enet_delete_desc_rings(pdata);
pdata->port_ops->shutdown(pdata);
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_main.h b/drivers/net/ethernet/apm/xgene/xgene_enet_main.h
index 0fe1a96..c2804c2 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_main.h
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_main.h
@@ -212,6 +212,8 @@ struct xgene_enet_pdata {
u32 mss;
u8 tx_delay;
u8 rx_delay;
+ struct device_node *mdio_np;
+ int phy_id;
bool mdio_driver;
};
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c b/drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c
index a7a6c05..ae93dc2 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c
@@ -257,9 +257,7 @@ static void xgene_sgmac_set_speed(struct xgene_enet_pdata *p)
u32 mc2, value;
if (p->phy_speed != SPEED_UNKNOWN) {
- value = xgene_mii_phy_read(p, INT_PHY_ADDR,
- SGMII_BASE_PAGE_ABILITY_ADDR >> 2);
- if (!(value & LINK_UP)) {
+ if (!xgene_enet_link_status(p)) {
xgene_mii_phy_write(p, INT_PHY_ADDR,
SGMII_TBI_CONTROL_ADDR >> 2,
0x8000);
@@ -325,7 +323,8 @@ static void xgene_sgmac_init(struct xgene_enet_pdata *p)
u32 enet_spare_cfg_reg, rsif_config_reg;
u32 cfg_bypass_reg, rx_dv_gate_reg;
- xgene_sgmac_reset(p);
+ if (!(p->enet_id == XGENE_ENET2 && p->mdio_driver))
+ xgene_sgmac_reset(p);
/* Enable auto-negotiation */
xgene_mii_phy_write(p, INT_PHY_ADDR, SGMII_TBI_CONTROL_ADDR >> 2,
@@ -416,6 +415,8 @@ static void xgene_sgmac_tx_disable(struct xgene_enet_pdata *p)
static int xgene_enet_reset(struct xgene_enet_pdata *p)
{
+ int ret;
+
if (!xgene_ring_mgr_init(p))
return -ENODEV;
@@ -428,7 +429,9 @@ static int xgene_enet_reset(struct xgene_enet_pdata *p)
clk_prepare_enable(p->clk);
}
- xgene_enet_ecc_init(p);
+ ret = xgene_enet_ecc_init(p);
+ if (ret)
+ return ret;
xgene_enet_config_ring_if_assoc(p);
return 0;
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
