Warning (unit_address_vs_reg): Node /keyboard/button@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /keyboard/button@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /keyboard/button@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /keyboard/button@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@8 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
---
v2:
- Change regulator name from fixedregulator3v3 to regulator-3v3.
---
arch/arm/boot/dts/r8a7790-lager.dts | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 749ba02b6a53a9de..9d20ace33b01d935 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -76,28 +76,28 @@
keyboard {
compatible = "gpio-keys";
- button@1 {
+ one {
linux,code = <KEY_1>;
label = "SW2-1";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
};
- button@2 {
+ two {
linux,code = <KEY_2>;
label = "SW2-2";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
};
- button@3 {
+ three {
linux,code = <KEY_3>;
label = "SW2-3";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
};
- button@4 {
+ four {
linux,code = <KEY_4>;
label = "SW2-4";
wakeup-source;
@@ -119,7 +119,7 @@
};
};
- fixedregulator3v3: fixedregulator@0 {
+ fixedregulator3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
@@ -128,7 +128,7 @@
regulator-always-on;
};
- vcc_sdhi0: regulator@1 {
+ vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
@@ -139,7 +139,7 @@
enable-active-high;
};
- vccq_sdhi0: regulator@2 {
+ vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
@@ -152,7 +152,7 @@
1800000 0>;
};
- vcc_sdhi2: regulator@3 {
+ vcc_sdhi2: regulator-vcc-sdhi2 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
@@ -163,7 +163,7 @@
enable-active-high;
};
- vccq_sdhi2: regulator@4 {
+ vccq_sdhi2: regulator-vccq-sdhi2 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
@@ -263,7 +263,7 @@
* instantiate the slave device at runtime according to the documentation.
* You can then communicate with the slave via IIC3.
*/
- i2cexio: i2c@8 {
+ i2cexio: i2c-8 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic0>, <&i2c0>;
i2c-bus-name = "i2c-exio";
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
