Re: [RFC] Reset pins of phys and their representation in a device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




[adding Krzysztof as cc]

On Thu, May 12, 2016 at 8:25 AM, Sergei Shtylyov
<sergei.shtylyov@xxxxxxxxxxxxxxxxxx> wrote:
> Hello.
>
>
> On 5/12/2016 10:15 AM, Uwe Kleine-König wrote:
>
>> I have a machine here where the reset pin of the phy is connected to a
>> GPIO.
>>
>> There are different possibilities available today to handle this
>> situation, here are the ones I'm aware of:
>>
>>  - Use a gpio-hog to set the reset gpio to non-active
>>    This might result in dependency problems (and that's what I am
>>    currently faced with) because there is no connection in the device
>>    tree between the hog and the phy.
>>
>>  - [Documentation/devicetree/bindings/net/fsl-fec.txt]
>>    The fec node supports properties
>>
>>         phy-reset-gpios = <&gpio2 14 0>;
>>         phy-reset-duration = <200> /* milliseconds */;
>>
>>    Something similar exists in TI's vendor kernel
>>
>> (http://git.ti.com/ti-linux-kernel/ti-linux-kernel/commit/17d192b999ee904ced223c16cef76111a51c461b)
>>    with different (and IMHO bader) naming.
>>    This is the wrong place to specify the gpios; they shouldn't be in the
>>    mac's node, but in a phy node instead.
>>
>> So what I actually want is to put the gpio specification in the right
>> place and let it look as follows:
>>
>>         mymdiobus {
>>                 [...]
>>                 myfirstphy: ethernet-phy@0 {
>>                         compatible = "ethernet-phy-ieee802.3-c22";
>>                         reg = <0>;
>>
>>                         reset-gpios = <&gpio2 14 0>;
>>                         reset-duration-ms = <200>;
>>                 };
>>
>>                 mysecondphy: ethernet-phy@2 {
>>                         compatible = "ethernet-phy-ieee802.3-c22";
>>                         reg = <2>;
>>
>>                         reset-gpios = <&gpio3 10 0>;
>>                         reset-duration-ms = <200>;
>>                 };
>>         };
>>
>> And with this we could defer probe of &myfirstphy if &gpio2 isn't
>> available yet.
>>
>> Does this sound sensible? Does something like that already exist which I
>> missed? Any further ideas/comments?
>
>
> http://patchwork.ozlabs.org/patch/616495/
>
>    I'll post a new version RSN.
>

This seems to be similar to what's needed by MMC/SD/SDIO devices (i.e:
a WiFi chip) that needs some power sequence for reset and be
enumerable.

Krzysztof has been working  to make the MMC pwrseq framework more
generic [0] since he wants to use it also for built-in USB devices.

>From a quick look at the patches mentioned in this thread, it seems
that the same framework can be used to reset the PHYs unless I'm
missing something. Have you considered using this? It would be good if
there is a consistent way to define the power sequence for devices
across the different subsystems.

[0]: https://lkml.org/lkml/2016/5/5/230

Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux