On Mon, Nov 18, 2013 at 3:34 PM, Grygorii Strashko <grygorii.strashko@xxxxxx> wrote: > On 11/18/2013 03:11 PM, Linus Walleij wrote: >> I think we recently established that map creating cannot be done >> in gpio_to_irq* functions as that will not work properly if you request >> an IRQ from device tree without first obtaining the IRQ from the GPIO >> number with this function. > > Why? Could you point on corresponding thread, pls? All that contain this: "gpio: interrupt consistency check for OF GPIO IRQs" http://marc.info/?l=linux-kernel&w=2&r=1&s=interrupt+consistency&q=b > Current call tree is: > irq_create_of_mapping() > |-hwirq = omain->ops->xlate() > |-irq_create_mapping(domain, hwirq) OK that works for the pure device-tree scenario so mostly this is OK. The problem that appear is if someone is using platform data-provided IRQs off the irq_chip without calling gpio_to_irq() on the GPIO line first. This has been determined to be legal to do, so preferably create the map when registering the lines. >> Also: please write a patch that marks the IRQ lines. >> Call gpio_lock_as_irq(*gpio_chip, offset); in the >> irqchip startup/shutdown functions. (Can be a separate >> patch.) > > It seems, some misunderstanding is here. So I'd like to clarify few points > and would be very appreciate for your comments: > 1) This patch itself will work unless we switch to DT (as in the following > patch) Sure.... but this does not seem to have much to do with my request to use gpio_lock_as_irq(). > 2) After this patch the following object structure will be created during > Davinci GPIO driver initialization (DA850 has 144 IRQ lines): > - gpio_chip0(0..31) > |- irq_domain1 > - gpio_chip1(32..63) > |- irq_domain2 > - gpio_chip2(64..95) > |- irq_domain3 > - gpio_chip3(96..127) > |- irq_domain4 > - gpio_chip4(128..143) > |- irq_domain5 OK that's nice. > 3) But in case of DT only one GPIO controller node will be created > Example: > gpio: gpio@1e26000 { > compatible = "ti,dm6441-gpio"; > gpio-controller; > reg = <0x226000 0x1000>; > interrupt-parent = <&intc>; > interrupts = <42 IRQ_TYPE_EDGE_BOTH 43 IRQ_TYPE_EDGE_BOTH > 44 IRQ_TYPE_EDGE_BOTH 45 IRQ_TYPE_EDGE_BOTH > 46 IRQ_TYPE_EDGE_BOTH 47 IRQ_TYPE_EDGE_BOTH > 48 IRQ_TYPE_EDGE_BOTH 49 IRQ_TYPE_EDGE_BOTH > 50 IRQ_TYPE_EDGE_BOTH>; > interrupt-controller; > #interrupt-cells = <2>; > ti,ngpio = <144>; > ti,davinci-gpio-unbanked = <0>; > } Yep... > 4) As result, to make GPIO bindings/mappings work - we'll need to implement > .of_xlate() callback per GPIO chip, which will provide us with valid valid > gpio_chip and offset of gpio inside chip > (It was discussed before and supposed to be done as next step). Yeah.. this is usually a bit tricky. > For example, gpio_chip3 and offset=15 should be selected: > devA { > gpios = <&gpio 111 GPIO_ACTIVE_HIGH>; > } > > 5) What should be done to make GPIO IRQ bindings/mappings work? > > Example: > devB { > interrupt-parent = <&gpio>; > interrupts = <111 IRQ_TYPE_EDGE_BOTH>; > } > > Should we implement one IRQ domain per all GPIO chips (per GPIO controller)? I don't know, I cannot really see where the problem is. The IRQ domain is for translationg hardware numbers such as bit offsets into Linux IRQ numbers and nothing else, so I'd suggest that as long as the thing you are translating/mapping is something simple like a bit index you're doing the right thing. If it becomes something complex where that index is not just a bit but an index into an array of registers at various locations it is abusing the irqdomain. So I think you should create one irqdomain per GPIO instance or bank or whatever you want to call it: like if there is this one register with 32 bits, then it gets its own IRQdomain. I think you should try to keep the 5 irqdomains, but whatever gives the simplest code is usually the right answer, and divide-and-conquer (split down the problem) is usually a good idea. How the GPIO block(s) are represented in the device tree is another totally separate issue about hardware description, do not let the device tree model your driver structure. Yours, Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
