Add devicetree binding for the TI DA850/OMAP-L138/AM18xx MultiChannel Buffered Serial Port (McBSP) The optional register range "dat" is not implemented at the moment. The current driver supports only DMA into RX/TX registers but no FIFO. Once the FIFO is implemented in the driver the "dat" range will be used. Signed-off-by: Petr Kulhavy <petr@xxxxxxxxx> --- v1: initial v2: add missing TC channel in dmas properties (for compatibility with the new EDMA3 binding) remove "-audio" postfix from the compatible string remove "channel-combine" property v3: remove the index note from the "mpu" property. specify exactly the supported platforms in compatible string v4: minor correction in the example ("interrupt names"), re-added index note to the "mpu" property. v5: example updated to match da850.dtsi: using "sound@" and removed leading zeros from the reg property .../devicetree/bindings/sound/davinci-mcbsp.txt | 52 ++++++++++++++++++++++ 1 file changed, 52 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/davinci-mcbsp.txt diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt new file mode 100644 index 000000000000..e9184ff3c2fa --- /dev/null +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -0,0 +1,52 @@ +Texas Instruments DaVinci McBSP module +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +This binding describes the "Multi-channel Buffered Serial Port" (McBSP) +audio interface found in some TI DaVinci processors like the OMAP-L138 or AM180x. + + +Required properties: +~~~~~~~~~~~~~~~~~~~~ +- compatible : + "ti,da850-mcbsp" : for DA850, AM180x and OPAM-L138 platforms + +- reg : physical base address and length of the controller memory mapped + region(s). +- reg-names : Should contain: + * "mpu" for the main registers (required). For compatibility + with the existing software, this is required to be the first entry. + * "dat" for the data FIFO (optional). + +- dmas: three element list of DMA controller phandles, DMA request line and + TC channel ordered triplets. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. The dma + identifiers must be "rx" and "tx". + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ +- interrupts : Interrupt numbers for McBSP +- interrupt-names : Known interrupt names are "rx" and "tx" + +- pinctrl-0: Should specify pin control group used for this controller. +- pinctrl-names: Should contain only one value - "default", for more details + please refer to pinctrl-bindings.txt + +Example (AM1808): +~~~~~~~~~~~~~~~~~ + +mcbsp0: sound@110000 { + compatible = "ti,da850-mcbsp"; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp0_pins>; + + reg = <0x110000 0x1000>, + <0x310000 0x1000>; + reg-names = "mpu", "dat"; + interrupts = <97 98>; + interrupt-names = "rx", "tx"; + dmas = <&edma0 3 1 + &edma0 2 1>; + dma-names = "tx", "rx"; + status = "okay"; +}; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html