The EBI (External Bus Interface) is used to access external peripherals
(NOR, SRAM, NAND, and other specific devices like ethernet controllers).
Each device is assigned a CS line and an address range and can have its
own configuration (timings, access mode, bus width, ...).
This driver provides a generic DT binding to configure a device according
to its requirements.
For specific device controllers (like the NAND one) the SMC timings
should be configured by the controller driver through the matrix and
smc syscon regmaps.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@xxxxxxxxxxxxxxx>
Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
---
Changes since v6:
- rework the binding to put per-device config information into a
separate subnode and have devices connected to the EBI bus
defined as direct children of the EBI node
- make all EBI timings mandatory
- keep adding sub-devices when a failure occurs on one of them
Changes since v5:
- remove the "atmel,specialized-logic" property: now all devices are
are attached to the SMC logic by default, and specialized drivers
(like the NAND controller one), should change this configuration
manually.
- provide hardware readout to allow partial config description.
This is mainly here to keep existing platforms (where everything
is configured by the bootloader/bootstrap) in working state.
- rename "atmel,tdf-optimized" into "atmel,tdf-mode" and switch from
a boolean to string property to properly support partial config
Changes since v4:
- fix inconsistencies in SMC and MATRIX registers definition
- add missing compatible strings for at91sam9rl SoC
- fix DT bindings documentation
- replace "atmel,generic-dev" property by "atmel,specialized-logic"
Changes since v3:
- added AT91_MATRIX_USBPUCR_PUON definition
- removed useless macros (those directly returning SoC specific register
offsets)
- use syscon_regmap_lookup_by_phandle instead of of_parse_phandle +
syscon_node_to_regmap
- drop AT91_EBICSA_REGFIELD and AT91_MULTI_EBICSA_REGFIELD macros
Changes since v2:
- minor fixes int DT bindings doc
- fix SMC macros
- make use of SMC macros defined in include/linux/mfd/syscon/atmel-smc.h
Changes since v1:
- almost everything :-)
drivers/memory/Kconfig | 11 +
drivers/memory/Makefile | 1 +
drivers/memory/atmel-ebi.c | 681 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 693 insertions(+)
create mode 100644 drivers/memory/atmel-ebi.c
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 51d5cd2..4780136 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -25,6 +25,17 @@ config ATMEL_SDRAMC
Starting with the at91sam9g45, this controller supports SDR, DDR and
LP-DDR memories.
+config ATMEL_EBI
+ bool "Atmel EBI driver"
+ default y
+ depends on ARCH_AT91 && OF
+ select MFD_SYSCON
+ help
+ Driver for Atmel EBI controller.
+ Used to configure the EBI (external bus interface) when the device-
+ tree is used. This bus supports NANDs, external ethernet controller,
+ SRAMs, ATA devices, etc.
+
config TI_AEMIF
tristate "Texas Instruments AEMIF driver"
depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index 890bdf4..965da6b 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_OF) += of_memory.o
endif
obj-$(CONFIG_ARM_PL172_MPMC) += pl172.o
obj-$(CONFIG_ATMEL_SDRAMC) += atmel-sdramc.o
+obj-$(CONFIG_ATMEL_EBI) += atmel-ebi.o
obj-$(CONFIG_TI_AEMIF) += ti-aemif.o
obj-$(CONFIG_TI_EMIF) += emif.o
obj-$(CONFIG_OMAP_GPMC) += omap-gpmc.o
diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
new file mode 100644
index 0000000..7f6b70b
--- /dev/null
+++ b/drivers/memory/atmel-ebi.c
@@ -0,0 +1,681 @@
+/*
+ * EBI driver for Atmel chips
+ * inspired by the fsl weim bus driver
+ *
+ * Copyright (C) 2013 JJ Hiblot.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/atmel-matrix.h>
+#include <linux/mfd/syscon/atmel-smc.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+struct at91sam9_smc_timings {
+ u32 ncs_rd_setup_ns;
+ u32 nrd_setup_ns;
+ u32 ncs_wr_setup_ns;
+ u32 nwe_setup_ns;
+ u32 ncs_rd_pulse_ns;
+ u32 nrd_pulse_ns;
+ u32 ncs_wr_pulse_ns;
+ u32 nwe_pulse_ns;
+ u32 nrd_cycle_ns;
+ u32 nwe_cycle_ns;
+ u32 tdf_ns;
+};
+
+struct at91sam9_smc_generic_fields {
+ struct regmap_field *setup;
+ struct regmap_field *pulse;
+ struct regmap_field *cycle;
+ struct regmap_field *mode;
+};
+
+struct at91sam9_ebi_dev_config {
+ struct at91sam9_smc_timings timings;
+ u32 mode;
+};
+
+struct at91_ebi_dev_config {
+ int cs;
+ union {
+ struct at91sam9_ebi_dev_config sam9;
+ };
+};
+
+struct at91_ebi;
+
+struct at91_ebi_dev {
+ struct list_head node;
+ struct at91_ebi *ebi;
+ u32 mode;
+ int numcs;
+ struct at91_ebi_dev_config configs[];
+};
+
+struct at91_ebi_caps {
+ unsigned int available_cs;
+ const struct reg_field *ebi_csa;
+ void (*get_config)(struct at91_ebi_dev *ebid,
+ struct at91_ebi_dev_config *conf);
+ int (*xlate_config)(struct at91_ebi_dev *ebid,
+ struct device_node *configs_np,
+ struct at91_ebi_dev_config *conf);
+ int (*apply_config)(struct at91_ebi_dev *ebid,
+ struct at91_ebi_dev_config *conf);
+ int (*init)(struct at91_ebi *ebi);
+};
+
+struct at91_ebi {
+ struct clk *clk;
+ struct regmap *smc;
+ struct regmap *matrix;
+
+ struct regmap_field *ebi_csa;
+
+ struct device *dev;
+ const struct at91_ebi_caps *caps;
+ struct list_head devs;
+ union {
+ struct at91sam9_smc_generic_fields sam9;
+ };
+};
+
+static void at91sam9_ebi_get_config(struct at91_ebi_dev *ebid,
+ struct at91_ebi_dev_config *conf)
+{
+ struct at91sam9_smc_generic_fields *fields = &ebid->ebi->sam9;
+ unsigned int clk_rate = clk_get_rate(ebid->ebi->clk);
+ struct at91sam9_ebi_dev_config *config = &conf->sam9;
+ struct at91sam9_smc_timings *timings = &config->timings;
+ unsigned int val;
+
+ regmap_fields_read(fields->mode, conf->cs, &val);
+ config->mode = val & ~AT91_SMC_TDF;
+
+ val = (val & AT91_SMC_TDF) >> 16;
+ timings->tdf_ns = clk_rate * val;
+
+ regmap_fields_read(fields->setup, conf->cs, &val);
+ timings->ncs_rd_setup_ns = (val >> 24) & 0x1f;
+ timings->ncs_rd_setup_ns += ((val >> 29) & 0x1) * 128;
+ timings->ncs_rd_setup_ns *= clk_rate;
+ timings->nrd_setup_ns = (val >> 16) & 0x1f;
+ timings->nrd_setup_ns += ((val >> 21) & 0x1) * 128;
+ timings->nrd_setup_ns *= clk_rate;
+ timings->ncs_wr_setup_ns = (val >> 8) & 0x1f;
+ timings->ncs_wr_setup_ns += ((val >> 13) & 0x1) * 128;
+ timings->ncs_wr_setup_ns *= clk_rate;
+ timings->nwe_setup_ns = val & 0x1f;
+ timings->nwe_setup_ns += ((val >> 5) & 0x1) * 128;
+ timings->nwe_setup_ns *= clk_rate;
+
+ regmap_fields_read(fields->pulse, conf->cs, &val);
+ timings->ncs_rd_pulse_ns = (val >> 24) & 0x3f;
+ timings->ncs_rd_pulse_ns += ((val >> 30) & 0x1) * 256;
+ timings->ncs_rd_pulse_ns *= clk_rate;
+ timings->nrd_pulse_ns = (val >> 16) & 0x3f;
+ timings->nrd_pulse_ns += ((val >> 22) & 0x1) * 256;
+ timings->nrd_pulse_ns *= clk_rate;
+ timings->ncs_wr_pulse_ns = (val >> 8) & 0x3f;
+ timings->ncs_wr_pulse_ns += ((val >> 14) & 0x1) * 256;
+ timings->ncs_wr_pulse_ns *= clk_rate;
+ timings->nwe_pulse_ns = val & 0x3f;
+ timings->nwe_pulse_ns += ((val >> 6) & 0x1) * 256;
+ timings->nwe_pulse_ns *= clk_rate;
+
+ regmap_fields_read(fields->cycle, conf->cs, &val);
+ timings->nrd_cycle_ns = (val >> 16) & 0x7f;
+ timings->nrd_cycle_ns += ((val >> 23) & 0x3) * 256;
+ timings->nrd_cycle_ns *= clk_rate;
+ timings->nwe_cycle_ns = val & 0x7f;
+ timings->nwe_cycle_ns += ((val >> 7) & 0x3) * 256;
+ timings->nwe_cycle_ns *= clk_rate;
+}
+
+static int at91sam9_smc_xslate_timings(struct at91_ebi_dev *ebid,
+ struct device_node *np,
+ struct at91sam9_smc_timings *timings)
+{
+ int ret;
+
+ ret = of_property_read_u32(np, "atmel,ncs-rd-setup-ns",
+ &timings->ncs_rd_setup_ns);
+ ret |= of_property_read_u32(np, "atmel,nrd-setup-ns",
+ &timings->nrd_setup_ns);
+ ret |= of_property_read_u32(np, "atmel,ncs-wr-setup-ns",
+ &timings->ncs_wr_setup_ns);
+ ret |= of_property_read_u32(np, "atmel,nwe-setup-ns",
+ &timings->nwe_setup_ns);
+ ret |= of_property_read_u32(np, "atmel,ncs-rd-pulse-ns",
+ &timings->ncs_rd_pulse_ns);
+ ret |= of_property_read_u32(np, "atmel,nrd-pulse-ns",
+ &timings->nrd_pulse_ns);
+ ret |= of_property_read_u32(np, "atmel,ncs-wr-pulse-ns",
+ &timings->ncs_wr_pulse_ns);
+ ret |= of_property_read_u32(np, "atmel,nwe-pulse-ns",
+ &timings->nwe_pulse_ns);
+ ret |= of_property_read_u32(np, "atmel,nwe-cycle-ns",
+ &timings->nwe_cycle_ns);
+ ret |= of_property_read_u32(np, "atmel,nrd-cycle-ns",
+ &timings->nrd_cycle_ns);
+ ret |= of_property_read_u32(np, "atmel,tdf-ns",
+ &timings->tdf_ns);
+
+ if (ret) {
+ dev_err(ebid->ebi->dev,
+ "missing or invalid timings definition in %s",
+ np->name);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int at91sam9_ebi_xslate_config(struct at91_ebi_dev *ebid,
+ struct device_node *np,
+ struct at91_ebi_dev_config *conf)
+{
+ struct at91sam9_ebi_dev_config *config = &conf->sam9;
+ const char *tmp_str;
+ u32 tmp;
+ int ret;
+
+ ret = of_property_read_u32(np, "atmel,bus-width", &tmp);
+ if (!ret) {
+ switch (tmp) {
+ case 8:
+ config->mode |= AT91_SMC_DBW_8;
+ break;
+
+ case 16:
+ config->mode |= AT91_SMC_DBW_16;
+ break;
+
+ case 32:
+ config->mode |= AT91_SMC_DBW_32;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ }
+
+ tmp_str = NULL;
+ of_property_read_string(np, "atmel,tdf-mode", &tmp_str);
+ if (tmp_str && !strcmp(tmp_str, "optimized"))
+ config->mode |= AT91_SMC_TDFMODE_OPTIMIZED;
+
+ tmp_str = NULL;
+ of_property_read_string(np, "atmel,byte-access-type", &tmp_str);
+ if (tmp_str && !strcmp(tmp_str, "write"))
+ config->mode |= AT91_SMC_BAT_WRITE;
+
+ tmp_str = NULL;
+ of_property_read_string(np, "atmel,read-mode", &tmp_str);
+ if (tmp_str && !strcmp(tmp_str, "nrd"))
+ config->mode |= AT91_SMC_READMODE_NRD;
+
+ tmp_str = NULL;
+ of_property_read_string(np, "atmel,write-mode", &tmp_str);
+ if (tmp_str && !strcmp(tmp_str, "nwe"))
+ config->mode |= AT91_SMC_WRITEMODE_NWE;
+
+ tmp_str = NULL;
+ of_property_read_string(np, "atmel,exnw-mode", &tmp_str);
+ if (tmp_str) {
+ if (!strcmp(tmp_str, "frozen"))
+ config->mode |= AT91_SMC_EXNWMODE_FROZEN;
+ else if (!strcmp(tmp_str, "ready"))
+ config->mode |= AT91_SMC_EXNWMODE_READY;
+ }
+
+ ret = of_property_read_u32(np, "atmel,page-mode", &tmp);
+ if (!ret) {
+ switch (tmp) {
+ case 4:
+ config->mode |= AT91_SMC_PS_4;
+ break;
+
+ case 8:
+ config->mode |= AT91_SMC_PS_8;
+ break;
+
+ case 16:
+ config->mode |= AT91_SMC_PS_16;
+ break;
+
+ case 32:
+ config->mode |= AT91_SMC_PS_32;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ config->mode |= AT91_SMC_PMEN;
+ }
+
+ return at91sam9_smc_xslate_timings(ebid, np, &config->timings);
+}
+
+static int at91sam9_ebi_apply_config(struct at91_ebi_dev *ebid,
+ struct at91_ebi_dev_config *conf)
+{
+ unsigned int clk_rate = clk_get_rate(ebid->ebi->clk);
+ struct at91sam9_ebi_dev_config *config = &conf->sam9;
+ struct at91sam9_smc_timings *timings = &config->timings;
+ struct at91sam9_smc_generic_fields *fields = &ebid->ebi->sam9;
+ u32 coded_val;
+ u32 val;
+
+ coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+ timings->ncs_rd_setup_ns);
+ val = AT91SAM9_SMC_NCS_NRDSETUP(coded_val);
+ coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+ timings->nrd_setup_ns);
+ val |= AT91SAM9_SMC_NRDSETUP(coded_val);
+ coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+ timings->ncs_wr_setup_ns);
+ val |= AT91SAM9_SMC_NCS_WRSETUP(coded_val);
+ coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+ timings->nwe_setup_ns);
+ val |= AT91SAM9_SMC_NWESETUP(coded_val);
+ regmap_fields_write(fields->setup, conf->cs, val);
+
+ coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+ timings->ncs_rd_pulse_ns);
+ val = AT91SAM9_SMC_NCS_NRDPULSE(coded_val);
+ coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+ timings->nrd_pulse_ns);
+ val |= AT91SAM9_SMC_NRDPULSE(coded_val);
+ coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+ timings->ncs_wr_pulse_ns);
+ val |= AT91SAM9_SMC_NCS_WRPULSE(coded_val);
+ coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+ timings->nwe_pulse_ns);
+ val |= AT91SAM9_SMC_NWEPULSE(coded_val);
+ regmap_fields_write(fields->pulse, conf->cs, val);
+
+ coded_val = at91sam9_smc_cycle_ns_to_cycles(clk_rate,
+ timings->nrd_cycle_ns);
+ val = AT91SAM9_SMC_NRDCYCLE(coded_val);
+ coded_val = at91sam9_smc_cycle_ns_to_cycles(clk_rate,
+ timings->nwe_cycle_ns);
+ val |= AT91SAM9_SMC_NWECYCLE(coded_val);
+ regmap_fields_write(fields->cycle, conf->cs, val);
+
+ val = DIV_ROUND_UP(timings->tdf_ns, clk_rate);
+ if (val > AT91_SMC_TDF_MAX)
+ val = AT91_SMC_TDF_MAX;
+ regmap_fields_write(fields->mode, conf->cs,
+ config->mode | AT91_SMC_TDF_(val));
+
+ return 0;
+}
+
+static int at91sam9_ebi_init(struct at91_ebi *ebi)
+{
+ struct at91sam9_smc_generic_fields *fields = &ebi->sam9;
+ struct reg_field field = REG_FIELD(0, 0, 31);
+
+ field.id_size = fls(ebi->caps->available_cs);
+ field.id_offset = AT91SAM9_SMC_GENERIC_BLK_SZ;
+
+ field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC);
+ fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->setup))
+ return PTR_ERR(fields->setup);
+
+ field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC);
+ fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->pulse))
+ return PTR_ERR(fields->pulse);
+
+ field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC);
+ fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->cycle))
+ return PTR_ERR(fields->cycle);
+
+ field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC);
+ fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->mode))
+ return PTR_ERR(fields->mode);
+
+ return 0;
+}
+
+static int sama5d3_ebi_init(struct at91_ebi *ebi)
+{
+ struct at91sam9_smc_generic_fields *fields = &ebi->sam9;
+ struct reg_field field = REG_FIELD(0, 0, 31);
+
+ field.id_size = fls(ebi->caps->available_cs);
+ field.id_offset = SAMA5_SMC_GENERIC_BLK_SZ;
+
+ field.reg = AT91SAM9_SMC_SETUP(SAMA5_SMC_GENERIC);
+ fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->setup))
+ return PTR_ERR(fields->setup);
+
+ field.reg = AT91SAM9_SMC_PULSE(SAMA5_SMC_GENERIC);
+ fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->pulse))
+ return PTR_ERR(fields->pulse);
+
+ field.reg = AT91SAM9_SMC_CYCLE(SAMA5_SMC_GENERIC);
+ fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->cycle))
+ return PTR_ERR(fields->cycle);
+
+ field.reg = SAMA5_SMC_MODE(SAMA5_SMC_GENERIC);
+ fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+ if (IS_ERR(fields->mode))
+ return PTR_ERR(fields->mode);
+
+ return 0;
+}
+
+static int at91_ebi_dev_setup(struct at91_ebi *ebi, struct device_node *np,
+ struct device_node *configs, int reg_cells)
+{
+ const struct at91_ebi_caps *caps = ebi->caps;
+ struct device *dev = ebi->dev;
+ struct at91_ebi_dev *ebid;
+ int ret, numcs = 0, i;
+
+ numcs = of_property_count_elems_of_size(np, "reg",
+ reg_cells * sizeof(u32));
+ if (numcs <= 0) {
+ dev_err(dev, "invalid reg property\n");
+ return -EINVAL;
+ }
+
+ ebid = devm_kzalloc(ebi->dev,
+ sizeof(*ebid) + (numcs * sizeof(*ebid->configs)),
+ GFP_KERNEL);
+ if (!ebid)
+ return -ENOMEM;
+
+ ebid->ebi = ebi;
+
+ for (i = 0; i < numcs; i++) {
+ struct at91_ebi_dev_config *conf = &ebid->configs[i];
+ struct device_node *conf_np;
+ char conf_name[16];
+ u32 cs;
+
+ ret = of_property_read_u32_index(np, "reg", i * reg_cells,
+ &cs);
+ if (ret)
+ return ret;
+
+ if (cs > AT91_MATRIX_EBI_NUM_CS ||
+ !(ebi->caps->available_cs & BIT(cs))) {
+ dev_err(dev, "invalid reg property\n");
+ return -EINVAL;
+ }
+
+ conf->cs = cs;
+ snprintf(conf_name, sizeof(conf_name), "config-%d", cs);
+ conf_np = of_get_child_by_name(configs, conf_name);
+ if (conf_np) {
+ ret = caps->xlate_config(ebid, conf_np, conf);
+ if (ret)
+ return ret;
+
+ ret = caps->apply_config(ebid, conf);
+ if (ret)
+ return ret;
+
+ /* Attach the EBI device to the generic SMC logic. */
+ if (ebi->ebi_csa)
+ regmap_field_update_bits(ebi->ebi_csa,
+ BIT(cs), 0);
+ of_node_put(conf_np);
+
+ }
+
+ caps->get_config(ebid, conf);
+ }
+
+ list_add_tail(&ebid->node, &ebi->devs);
+
+ return 0;
+}
+
+static const struct reg_field at91sam9260_ebi_csa =
+ REG_FIELD(AT91SAM9260_MATRIX_EBICSA, 0,
+ AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9260_ebi_caps = {
+ .available_cs = 0xff,
+ .ebi_csa = &at91sam9260_ebi_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9261_ebi_csa =
+ REG_FIELD(AT91SAM9261_MATRIX_EBICSA, 0,
+ AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9261_ebi_caps = {
+ .available_cs = 0xff,
+ .ebi_csa = &at91sam9261_ebi_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9263_ebi0_csa =
+ REG_FIELD(AT91SAM9263_MATRIX_EBI0CSA, 0,
+ AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9263_ebi0_caps = {
+ .available_cs = 0x3f,
+ .ebi_csa = &at91sam9263_ebi0_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9263_ebi1_csa =
+ REG_FIELD(AT91SAM9263_MATRIX_EBI1CSA, 0,
+ AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9263_ebi1_caps = {
+ .available_cs = 0x7,
+ .ebi_csa = &at91sam9263_ebi1_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9rl_ebi_csa =
+ REG_FIELD(AT91SAM9RL_MATRIX_EBICSA, 0,
+ AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9rl_ebi_caps = {
+ .available_cs = 0x3f,
+ .ebi_csa = &at91sam9rl_ebi_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9g45_ebi_csa =
+ REG_FIELD(AT91SAM9G45_MATRIX_EBICSA, 0,
+ AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9g45_ebi_caps = {
+ .available_cs = 0x3f,
+ .ebi_csa = &at91sam9g45_ebi_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct at91_ebi_caps at91sam9x5_ebi_caps = {
+ .available_cs = 0x3f,
+ .ebi_csa = &at91sam9263_ebi0_csa,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = at91sam9_ebi_init,
+};
+
+static const struct at91_ebi_caps sama5d3_ebi_caps = {
+ .available_cs = 0xf,
+ .get_config = at91sam9_ebi_get_config,
+ .xlate_config = at91sam9_ebi_xslate_config,
+ .apply_config = at91sam9_ebi_apply_config,
+ .init = sama5d3_ebi_init,
+};
+
+static const struct of_device_id at91_ebi_id_table[] = {
+ {
+ .compatible = "atmel,at91sam9260-ebi",
+ .data = &at91sam9260_ebi_caps,
+ },
+ {
+ .compatible = "atmel,at91sam9261-ebi",
+ .data = &at91sam9261_ebi_caps,
+ },
+ {
+ .compatible = "atmel,at91sam9263-ebi0",
+ .data = &at91sam9263_ebi0_caps,
+ },
+ {
+ .compatible = "atmel,at91sam9263-ebi1",
+ .data = &at91sam9263_ebi1_caps,
+ },
+ {
+ .compatible = "atmel,at91sam9rl-ebi",
+ .data = &at91sam9rl_ebi_caps,
+ },
+ {
+ .compatible = "atmel,at91sam9g45-ebi",
+ .data = &at91sam9g45_ebi_caps,
+ },
+ {
+ .compatible = "atmel,at91sam9x5-ebi",
+ .data = &at91sam9x5_ebi_caps,
+ },
+ {
+ .compatible = "atmel,sama5d3-ebi",
+ .data = &sama5d3_ebi_caps,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, at91_ebi_id_table);
+
+static int at91_ebi_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *child, *configs, *np = dev->of_node;
+ const struct of_device_id *match;
+ struct at91_ebi *ebi;
+ int ret, reg_cells;
+ struct clk *clk;
+ u32 val;
+
+ match = of_match_device(at91_ebi_id_table, dev);
+ if (!match || !match->data)
+ return -EINVAL;
+
+ ebi = devm_kzalloc(dev, sizeof(*ebi), GFP_KERNEL);
+ if (!ebi)
+ return -ENOMEM;
+
+ INIT_LIST_HEAD(&ebi->devs);
+ ebi->caps = match->data;
+ ebi->dev = dev;
+
+ clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ebi->clk = clk;
+
+ ebi->smc = syscon_regmap_lookup_by_phandle(np, "atmel,smc");
+ if (IS_ERR(ebi->smc))
+ return PTR_ERR(ebi->smc);
+
+ /*
+ * The sama5d3 does not provide an EBICSA register and thus does need
+ * to access the matrix registers.
+ */
+ if (ebi->caps->ebi_csa) {
+ ebi->matrix =
+ syscon_regmap_lookup_by_phandle(np, "atmel,matrix");
+ if (IS_ERR(ebi->matrix))
+ return PTR_ERR(ebi->matrix);
+
+ ebi->ebi_csa = regmap_field_alloc(ebi->matrix,
+ *ebi->caps->ebi_csa);
+ if (IS_ERR(ebi->ebi_csa))
+ return PTR_ERR(ebi->ebi_csa);
+ }
+
+ ret = ebi->caps->init(ebi);
+ if (ret)
+ return ret;
+
+ configs = of_get_child_by_name(np, "configs");
+
+ ret = of_property_read_u32(np, "#address-cells", &val);
+ if (ret) {
+ dev_err(dev, "missing #address-cells property\n");
+ return ret;
+ }
+
+ reg_cells = val;
+
+ ret = of_property_read_u32(np, "#size-cells", &val);
+ if (ret) {
+ dev_err(dev, "missing #address-cells property\n");
+ return ret;
+ }
+
+ reg_cells += val;
+
+ for_each_available_child_of_node(np, child) {
+ if (!of_find_property(child, "reg", NULL))
+ continue;
+
+ ret = at91_ebi_dev_setup(ebi, child, configs, reg_cells);
+ if (ret)
+ dev_err(dev, "failed to instantiate %s",
+ child->name);
+ }
+ of_node_put(configs);
+
+ return of_platform_populate(np, NULL, NULL, dev);
+}
+
+static struct platform_driver at91_ebi_driver = {
+ .driver = {
+ .name = "atmel-ebi",
+ .of_match_table = at91_ebi_id_table,
+ },
+};
+module_platform_driver_probe(at91_ebi_driver, at91_ebi_probe);
+
+MODULE_AUTHOR("JJ Hiblot");
+MODULE_DESCRIPTION("Atmel EBI driver");
+MODULE_LICENSE("GPL");
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
