Hi,
On 15.04.2016 18:46, Grygorii Strashko wrote:
On 04/12/2016 08:25 PM, Marcin Niestroj wrote:
Hi,
On 08.04.2016 19:16, Grygorii Strashko wrote:
On 04/08/2016 06:14 PM, Tony Lindgren wrote:
* Grygorii Strashko <grygorii.strashko@xxxxxx> [160408 03:41]:
Hi Tony,
On 04/05/2016 01:40 AM, Tony Lindgren wrote:
Hi,
* Marcin Niestroj <m.niestroj@xxxxxxxxxxxxxxxx> [160404 08:57]:
Support configuration of ext_wakeup sources. This patch makes it
possible to enable ext_wakeup and set it's polarity, depending on
board
configuration. AM335x's dedicated PMIC (tps65217) uses ext_wakeup to
notify about power-button presses. Handling power-button presses
enables
to recover from RTC-only power states correctly.
I suggest you just set this pin up as a minimal gpiochip. That way
we can use the standard binding :) And if we get lucky, this pin can
also trigger during runtime.
Following my comments on v2 of this patch I propose to rollback to
this version of the patch.
It seems doesn't fit in gpiochip, it's more likely irqchip, but since
rtc can't generate IRQ there are nor reasons for these genetic
experiments and RTC's specific bindings looks more suitable, at
least for me.
Hmm well gpiochips typically are irqchip too. IMO the generic binding
here sounds like "gpio-wakeup" as it's an input with polarity and with
an optional interrupt.
Plain irqchip would work too in this case if there are no other GPIO
specific features. Some other RTCs may have more GPIO like features.
In any case, setting the ext_wakeup up as an irqchip means that the
RTC controller can be used as a dedicated wakeirq with Linux :)
It can't :( It can't generate IRQ when state of ext_wakeup line has
been changed.
Are you guys sure there's no wake pin events during runtime? AFAIK
the RTCs just typically produce an interrupt when programmed to
do so, they don't know the state of the SoC.
I do not think that It can be fit in gpiochip or irqchip -
in my opinion right way is to proceed with bindings proposed by
Marcin in this patch v1.
But, probably, it could fit in pinctrl:
- this is pin's configuration
- this is one-time configuration
- or - configuration which can be applied before suspend
and resorted after suspend.
if you still wanna try some generic framework.
pinctrl bindings looks ok for our use case (enable/disable input,
configure debounce), except I don't see any way to pass polarity
(active low/high) to the driver.
Below code is just a POC that pinctrl can be used here.
It does one time configuration at boot, but more sates can be added
- sleep, poweroff:
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 13ac882..9580c82 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -1248,11 +1248,40 @@
rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
- reg = <0x48838000 0x100>;
+ reg = <0x48838000 0x98>;
interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "rtcss";
clocks = <&sys_32k_ck>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ rtc_pmx: pinmux@48838098 {
+ compatible = "pinctrl-single";
+ reg = <0x48838098 0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x007fffff>;
+
+ pinctrl-names = "default"/*, "sleep"*/;
+ pinctrl-0 = <&rtc_default>;
+/* pinctrl-1 = <&rtc_sleep>;*/
+
+ rtc_default: rtc_default {
+ pinctrl-single,pins = <
+ 0x0 0x000B0111
+ 0x4 0x00000004
+ >;
+ };
+/* rtc_sleep: rtc_sleep {
+ pinctrl-single,pins = <
+ 0x0 0x00000000
+ 0x4 0x00000000
+ >;
+ };*/
+ };
};
/* OCP2SCP1 */
diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c
index ec2e9c5..28c67a4 100644
--- a/drivers/rtc/rtc-omap.c
+++ b/drivers/rtc/rtc-omap.c
@@ -428,8 +428,10 @@ static void omap_rtc_power_off(void)
rtc->type->unlock(rtc);
/* enable pmic_power_en control */
+/*
val = rtc_readl(rtc, OMAP_RTC_PMIC_REG);
rtc_writel(rtc, OMAP_RTC_PMIC_REG, val | OMAP_RTC_PMIC_POWER_EN_EN);
+*/
/* set alarm two seconds from now */
omap_rtc_read_time_raw(rtc, &tm);
@@ -650,6 +652,8 @@ static int omap_rtc_probe(struct platform_device *pdev)
reg | OMAP_RTC_OSC_SEL_32KCLK_SRC);
}
+ of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+
rtc->type->lock(rtc);
device_init_wakeup(&pdev->dev, true);
I made few changes to the POC you provided.
In below code we check reg resource size in order to know if we
should update RTC_PMIC or it is pinctrl responsibility. It's a little
hack, but we make sure, that every device with not modified device-tree
will work as previously. If we want to add support for ext_wakeup, we
just change reg resouce size in device-tree in order to not overlap
requested memory regions in rtc-omap and pinctrl.
I used am335x-chilisom instead of dra7 and updated
pinctrl-single,funcion-mask so the EXT_WAKEUP_STATUS is always cleared
after boot.
So the question now is: is this acceptable? Do we want to continue with
this approach?
diff --git a/arch/arm/boot/dts/am335x-chilisom.dtsi
b/arch/arm/boot/dts/am335x-chilisom.dtsi
index bc0880d..525ed4f 100644
--- a/arch/arm/boot/dts/am335x-chilisom.dtsi
+++ b/arch/arm/boot/dts/am335x-chilisom.dtsi
@@ -124,6 +124,31 @@
&rtc {
system-power-controller;
+
+ reg = <0x44e3e000 0x98>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ rtc_pinmux: pinmux@0x44e3e098 {
+ compatible = "pinctrl-single";
+ reg = <0x44e3e098 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x10fff>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_pins_default>;
+
+ rtc_pins_default: rtc_pins_default {
+ pinctrl-single,pins = <
+ 0x0 0x00010011
+ 0x4 0x00000000
+ >;
+ };
+ };
};
/* NAND Flash */
diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c
index ec2e9c5..db2512c 100644
--- a/drivers/rtc/rtc-omap.c
+++ b/drivers/rtc/rtc-omap.c
@@ -134,6 +134,7 @@ struct omap_rtc_device_type {
struct omap_rtc {
struct rtc_device *rtc;
void __iomem *base;
+ resource_size_t res_size;
struct clk *clk;
int irq_alarm;
int irq_timer;
@@ -428,8 +429,11 @@ static void omap_rtc_power_off(void)
rtc->type->unlock(rtc);
/* enable pmic_power_en control */
- val = rtc_readl(rtc, OMAP_RTC_PMIC_REG);
- rtc_writel(rtc, OMAP_RTC_PMIC_REG, val | OMAP_RTC_PMIC_POWER_EN_EN);
+ if (rtc->res_size > OMAP_RTC_PMIC_REG) {
+ val = rtc_readl(rtc, OMAP_RTC_PMIC_REG);
+ rtc_writel(rtc, OMAP_RTC_PMIC_REG,
+ val | OMAP_RTC_PMIC_POWER_EN_EN);
+ }
/* set alarm two seconds from now */
omap_rtc_read_time_raw(rtc, &tm);
@@ -567,6 +571,7 @@ static int omap_rtc_probe(struct platform_device *pdev)
clk_prepare_enable(rtc->clk);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ rtc->res_size = resource_size(res);
rtc->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(rtc->base))
return PTR_ERR(rtc->base);
@@ -681,6 +686,9 @@ static int omap_rtc_probe(struct platform_device *pdev)
}
}
+ /* handle pinmux nodes which configure ext_wakeup inputs */
+ of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+
return 0;
err:
--
Marcin Niestroj
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html