Add devicetree binding for the TI DA850/OMAP-L138/AM18xx
MultiChannel Buffered Serial Port (McBSP)
The optional register range "dat" is not implemented at the moment.
The current driver supports only DMA into RX/TX registers but no FIFO.
Once the FIFO is implemented in the driver the "dat" range will be used.
Signed-off-by: Petr Kulhavy <petr@xxxxxxxxx>
---
v1: initial
v2: add missing TC channel in dmas properties (for compatibility with the new EDMA3 binding)
remove "-audio" postfix from the compatible string
remove "channel-combine" property
v3: remove the index note from the "mpu" property.
specify exactly the supported platforms in compatible string
v4: minor correction in the example ("interrupt names"), re-added index note to the "mpu" property.
.../devicetree/bindings/sound/davinci-mcbsp.txt | 52 ++++++++++++++++++++++
1 file changed, 52 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/davinci-mcbsp.txt
diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt
new file mode 100644
index 000000000000..bb957129b333
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt
@@ -0,0 +1,52 @@
+Texas Instruments DaVinci McBSP module
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+This binding describes the "Multi-channel Buffered Serial Port" (McBSP)
+audio interface found in some TI DaVinci processors like the OMAP-L138 or AM180x.
+
+
+Required properties:
+~~~~~~~~~~~~~~~~~~~~
+- compatible :
+ "ti,da850-mcbsp" : for DA850, AM180x and OPAM-L138 platforms
+
+- reg : physical base address and length of the controller memory mapped
+ region(s).
+- reg-names : Should contain:
+ * "mpu" for the main registers (required). For compatibility
+ with the existing software, this is required to be the first entry.
+ * "dat" for the data FIFO (optional).
+
+- dmas: three element list of DMA controller phandles, DMA request line and
+ TC channel ordered triplets.
+- dma-names: identifier string for each DMA request line in the dmas property.
+ These strings correspond 1:1 with the ordered pairs in dmas. The dma
+ identifiers must be "rx" and "tx".
+
+Optional properties:
+~~~~~~~~~~~~~~~~~~~~
+- interrupts : Interrupt numbers for McBSP
+- interrupt-names : Known interrupt names are "rx" and "tx"
+
+- pinctrl-0: Should specify pin control group used for this controller.
+- pinctrl-names: Should contain only one value - "default", for more details
+ please refer to pinctrl-bindings.txt
+
+Example (AM1808):
+~~~~~~~~~~~~~~~~~
+
+mcbsp0: mcbsp@1d10000 {
+ compatible = "ti,da850-mcbsp";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcbsp0_pins>;
+
+ reg = <0x00110000 0x1000>,
+ <0x00310000 0x1000>;
+ reg-names = "mpu", "dat";
+ interrupts = <97 98>;
+ interrupt-names = "rx", "tx";
+ dmas = <&edma0 3 1
+ &edma0 2 1>;
+ dma-names = "tx", "rx";
+ status = "okay";
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
