We used to use a fixed rate clock for the UARTs. Now that we have clock support we can associate the correct clocks to the UARTs and drop the 26MHz fixed rate UART clock. Signed-off-by: Erin Lo <erin.lo@xxxxxxxxxxxx> --- This patch dependents on "Add clock support for Mediatek MT2701"[1]. If we have clock support, we must associate the correct clocks to the UARTs. Otherwise it will cause booting issue. Please also accept this patch together with [1]. [1]http://lists.infradead.org/pipermail/linux-mediatek/2016-April/004938.html --- arch/arm/boot/dts/mt2701.dtsi | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi index 171d4da..e79e88f 100644 --- a/arch/arm/boot/dts/mt2701.dtsi +++ b/arch/arm/boot/dts/mt2701.dtsi @@ -71,12 +71,6 @@ #clock-cells = <0>; }; - uart_clk: dummy26m { - compatible = "fixed-clock"; - clock-frequency = <26000000>; - #clock-cells = <0>; - }; - clk26m: oscillator@0 { compatible = "fixed-clock"; #clock-cells = <0>; @@ -167,7 +161,8 @@ "mediatek,mt6577-uart"; reg = <0 0x11002000 0 0x400>; interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>; - clocks = <&uart_clk>; + clocks = <&pericfg CLK_PERI_UART0_SEL>, <&pericfg CLK_PERI_UART0>; + clock-names = "baud", "bus"; status = "disabled"; }; @@ -176,7 +171,8 @@ "mediatek,mt6577-uart"; reg = <0 0x11003000 0 0x400>; interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; - clocks = <&uart_clk>; + clocks = <&pericfg CLK_PERI_UART1_SEL>, <&pericfg CLK_PERI_UART1>; + clock-names = "baud", "bus"; status = "disabled"; }; @@ -185,7 +181,8 @@ "mediatek,mt6577-uart"; reg = <0 0x11004000 0 0x400>; interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_LOW>; - clocks = <&uart_clk>; + clocks = <&pericfg CLK_PERI_UART2_SEL>, <&pericfg CLK_PERI_UART2>; + clock-names = "baud", "bus"; status = "disabled"; }; @@ -194,7 +191,8 @@ "mediatek,mt6577-uart"; reg = <0 0x11005000 0 0x400>; interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_LOW>; - clocks = <&uart_clk>; + clocks = <&pericfg CLK_PERI_UART3_SEL>, <&pericfg CLK_PERI_UART3>; + clock-names = "baud", "bus"; status = "disabled"; }; }; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
