Re: [PATCH v1 1/2] dt/bindings/usb: Add bindings for PIC32 MUSB driver.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 4/7/2016 4:24 PM, Purna Chandra Mandal wrote:

Document devicetree binding for the USB controller

     Device tree.

ack.

and USB Phy found on Microchip PIC32 class devices.

     PHY.

ack.

Signed-off-by: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>

---

    .../bindings/usb/microchip,pic32-musb.txt          | 67 ++++++++++++++++++++++
    1 file changed, 67 insertions(+)
    create mode 100644 Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt

diff --git a/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt b/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
new file mode 100644
index 0000000..e1cec9d
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
@@ -0,0 +1,67 @@
+Microchip PIC32 MUSB DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible       : should be "microchip,pic32mzda-usb".
+ - reg              : offset and length of "MUSB Core Registers" and
+                      "USB Clock & Reset Registers".
+ - reg-names        : should be "mc", and "usbcr" in order
+ - clocks           : clock specifier for the musb controller clock
+ - clock-names      : should be "usb_clk"
+ - interrupts       : interrupt number for MUSB Core General interrupt
+                      and DMA interrupt
+ - interrupt-names  : must be "mc" and "dma" in order.
+ - phys             : phy specifier for the otg phy.
+ - dr_mode          : should be one of "host", "peripheral" or "otg".
+ - mentor,multipoint: Should be "1" indicating the musb controller supports
+                      multipoint. This is MUSB configuration-specific setting.
+ - mentor,num-eps   : Specifies the number of endpoints. This is also a
+                      MUSB configuration-specific setting. Should be set to "8".
+ - mentor,ram-bits  : Specifies the ram address size. Should be set to "11".
+ - mentor,power     : Should be "500". This signifies the controller can supply
+                      up to 500mA when operating in host mode.

     No, these "nentor" prefixed parameters must be determined from the "compatible" prop.

Prefix "mentor" here is used to signify configuration of the MUSB controller IP, not
specifics of the chip or glue logic.

    I know.

Please suggest if replacing with "microchip" makes it better.

    No, nothing of that sort. These parameters are probably fixed for the said PIC32 implementation? If so, they shouldn't appear as the node props but should instead be hard-coded in the glue layer. Don't look at the OMAP glues, they are a bad example.

ack. Will hard code.

Except "mentor, power", that is. It was a part of the real platform data, not the MUSB config. structure.

[...]

Thanks, Purna

MBR, Sergei

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux