DRA72-EVM now has an upgrade to Rev C with ES2.0 silicon. As part of
this change, a few updates were factored in that were software
incompatible with previous board in few areas:
- We now use DP83867 ethernet phy instead of older DP838865 which fails
in certain usecases.
- Two ethernet ports now instead of the single one in rev B.
- polarities changed for certain pcf gpios
- Due to SoC phy current requirements, VDDA supplies are split between
ldo5 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is
still supplied by ldo5.
NOTE: It does not make much sense to spin off a new board compatible
flag since there is no real benefit for the same.
Signed-off-by: Nishanth Menon <nm@xxxxxx>
---
arch/arm/boot/dts/Makefile | 3 +-
.../dts/{dra72-evm.dts => dra72-evm-common.dtsi} | 26 +-
arch/arm/boot/dts/dra72-evm-revc.dts | 73 ++
arch/arm/boot/dts/dra72-evm.dts | 835 +--------------------
4 files changed, 89 insertions(+), 848 deletions(-)
copy arch/arm/boot/dts/{dra72-evm.dts => dra72-evm-common.dtsi} (97%)
create mode 100644 arch/arm/boot/dts/dra72-evm-revc.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b25621ae2ff7..f74bd41cf58c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -527,7 +527,8 @@ dtb-$(CONFIG_SOC_DRA7XX) += \
am57xx-cl-som-am57x.dtb \
am57xx-sbc-am57x.dtb \
dra7-evm.dtb \
- dra72-evm.dtb
+ dra72-evm.dtb \
+ dra72-evm-revc.dtb
dtb-$(CONFIG_ARCH_ORION5X) += \
orion5x-lacie-d2-network.dtb \
orion5x-lacie-ethernet-disk-mini-v2.dtb \
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm-common.dtsi
similarity index 97%
copy from arch/arm/boot/dts/dra72-evm.dts
copy to arch/arm/boot/dts/dra72-evm-common.dtsi
index 6affe2d137da..94faab98cf0d 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -12,14 +12,8 @@
#include <dt-bindings/clk/ti-dra7-atl.h>
/ {
- model = "TI DRA722";
compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
- memory {
- device_type = "memory";
- reg = <0x0 0x80000000 0x0 0x40000000>; /* 1024 MB */
- };
-
aliases {
display0 = &hdmi0;
};
@@ -320,7 +314,7 @@
tps65917_pmic {
compatible = "ti,tps65917-pmic";
- regulators {
+ tps65917_regulators: regulators {
smps1_reg: smps1 {
/* VDD_MPU */
regulator-name = "smps1";
@@ -376,14 +370,6 @@
regulator-allow-bypass;
};
- ldo2_reg: ldo2 {
- /* LDO2_OUT --> TP1017 (UNUSED) */
- regulator-name = "ldo2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-allow-bypass;
- };
-
ldo3_reg: ldo3 {
/* VDDA_1V8_PHY */
regulator-name = "ldo3";
@@ -427,8 +413,6 @@
lines-initial-states = <0x1408>;
gpio-controller;
#gpio-cells = <2>;
- interrupt-parent = <&gpio6>;
- interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
};
@@ -689,13 +673,6 @@
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
pinctrl-1 = <&cpsw_sleep>;
- slaves = <1>;
- mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
-};
-
-&cpsw_emac0 {
- phy_id = <&davinci_mdio>, <3>;
- phy-mode = "rgmii";
};
&davinci_mdio {
@@ -785,7 +762,6 @@
&hdmi {
status = "ok";
- vdda-supply = <&ldo3_reg>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_pins>;
diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts
new file mode 100644
index 000000000000..23a3e60f22dc
--- /dev/null
+++ b/arch/arm/boot/dts/dra72-evm-revc.dts
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include "dra72-evm-common.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ model = "TI DRA722 Rev C EVM";
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */
+ };
+};
+
+&tps65917_regulators {
+ ldo2_reg: ldo2 {
+ /* LDO2_OUT --> VDDA_1V8_PHY2 */
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&hdmi {
+ vdda_video-supply = <&ldo2_reg>;
+};
+
+&pcf_gpio_21 {
+ interrupt-parent = <&gpio3>;
+ interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&mac {
+ mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
+ <&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */
+ <&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */
+ dual_emac;
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <2>;
+ phy-mode = "rgmii-id";
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <3>;
+ phy-mode = "rgmii-id";
+ dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+ dp83867_0: ethernet-phy@2 {
+ reg = <2>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+ };
+
+ dp83867_1: ethernet-phy@3 {
+ reg = <3>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+ };
+};
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 6affe2d137da..89fe7ba8ae01 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -1,694 +1,40 @@
/*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-/dts-v1/;
-
-#include "dra72x.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/ti-dra7-atl.h>
-
+#include "dra72-evm-common.dtsi"
/ {
model = "TI DRA722";
- compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
memory {
device_type = "memory";
reg = <0x0 0x80000000 0x0 0x40000000>; /* 1024 MB */
};
+};
- aliases {
- display0 = &hdmi0;
- };
-
- evm_3v3: fixedregulator-evm_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "evm_3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- aic_dvdd: fixedregulator-aic_dvdd {
- /* TPS77018DBVT */
- compatible = "regulator-fixed";
- regulator-name = "aic_dvdd";
- vin-supply = <&evm_3v3>;
+&tps65917_regulators {
+ ldo2_reg: ldo2 {
+ /* LDO2_OUT --> TP1017 (UNUSED) */
+ regulator-name = "ldo2";
regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- evm_3v3_sd: fixedregulator-sd {
- compatible = "regulator-fixed";
- regulator-name = "evm_3v3_sd";
- regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- enable-active-high;
- gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
- };
-
- extcon_usb1: extcon_usb1 {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
- };
-
- extcon_usb2: extcon_usb2 {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
- };
-
- hdmi0: connector {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
- };
-
- tpd12s015: encoder {
- compatible = "ti,tpd12s015";
-
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
- gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
- <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
- <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tpd12s015_in: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tpd12s015_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
-
- sound0: sound@0 {
- compatible = "simple-audio-card";
- simple-audio-card,name = "DRA7xx-EVM";
- simple-audio-card,widgets =
- "Headphone", "Headphone Jack",
- "Line", "Line Out",
- "Microphone", "Mic Jack",
- "Line", "Line In";
- simple-audio-card,routing =
- "Headphone Jack", "HPLOUT",
- "Headphone Jack", "HPROUT",
- "Line Out", "LLOUT",
- "Line Out", "RLOUT",
- "MIC3L", "Mic Jack",
- "MIC3R", "Mic Jack",
- "Mic Jack", "Mic Bias",
- "LINE1L", "Line In",
- "LINE1R", "Line In";
- simple-audio-card,format = "dsp_b";
- simple-audio-card,bitclock-master = <&sound0_master>;
- simple-audio-card,frame-master = <&sound0_master>;
- simple-audio-card,bitclock-inversion;
-
- sound0_master: simple-audio-card,cpu {
- sound-dai = <&mcasp3>;
- system-clock-frequency = <5644800>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&tlv320aic3106>;
- clocks = <&atl_clkin2_ck>;
- };
- };
-};
-
-&dra7_pmx_core {
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
- >;
- };
-
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
- DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
- >;
- };
-
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
- DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
- >;
- };
-
- nand_default: nand_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */
- DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */
- DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */
- DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */
- DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */
- DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */
- DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */
- DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */
- DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */
- DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */
- DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */
- DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */
- DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */
- DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */
- DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */
- DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */
- DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */
- DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */
- DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */
- DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */
- DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */
- DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- usb2_pins: pinmux_usb2_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
- >;
- };
-
- tps65917_pins_default: tps65917_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
- mmc1_pins_default: mmc1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
- DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
- DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
- DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
- DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
- DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
- DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
- >;
- };
-
- mmc2_pins_default: mmc2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
- DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
- DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
- DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
- DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
- DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
- DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
- DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
- DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
- DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
- >;
- };
-
- dcan1_pins_default: dcan1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
- DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
- >;
- };
-
- dcan1_pins_sleep: dcan1_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
- DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */
- >;
- };
-
- qspi1_pins: pinmux_qspi1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3474, PIN_OUTPUT | MUX_MODE1) /* gpmc_a13.qspi1_rtclk */
- DRA7XX_CORE_IOPAD(0x3478, PIN_INPUT | MUX_MODE1) /* gpmc_a14.qspi1_d3 */
- DRA7XX_CORE_IOPAD(0x347c, PIN_INPUT | MUX_MODE1) /* gpmc_a15.qspi1_d2 */
- DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */
- DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1) /* gpmc_a17.qspi1_d0 */
- DRA7XX_CORE_IOPAD(0x3488, PIN_OUTPUT | MUX_MODE1) /* qpmc_a18.qspi1_sclk */
- DRA7XX_CORE_IOPAD(0x34b8, PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */
- >;
- };
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- >;
- };
-
- atl_pins: pinmux_atl_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */
- DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */
- >;
- };
-
- mcasp3_pins: pinmux_mcasp3_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */
- >;
- };
-
- mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15)
- >;
- };
-};
-
-&i2c1 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- clock-frequency = <400000>;
-
- tps65917: tps65917@58 {
- compatible = "ti,tps65917";
- reg = <0x58>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&tps65917_pins_default>;
-
- interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
- interrupt-controller;
- #interrupt-cells = <2>;
-
- ti,system-power-controller;
-
- tps65917_pmic {
- compatible = "ti,tps65917-pmic";
-
- regulators {
- smps1_reg: smps1 {
- /* VDD_MPU */
- regulator-name = "smps1";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps2_reg: smps2 {
- /* VDD_CORE */
- regulator-name = "smps2";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1060000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- smps3_reg: smps3 {
- /* VDD_GPU IVA DSPEVE */
- regulator-name = "smps3";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- smps4_reg: smps4 {
- /* VDDS1V8 */
- regulator-name = "smps4";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps5_reg: smps5 {
- /* VDD_DDR */
- regulator-name = "smps5";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo1_reg: ldo1 {
- /* LDO1_OUT --> SDIO */
- regulator-name = "ldo1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-allow-bypass;
- };
-
- ldo2_reg: ldo2 {
- /* LDO2_OUT --> TP1017 (UNUSED) */
- regulator-name = "ldo2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-allow-bypass;
- };
-
- ldo3_reg: ldo3 {
- /* VDDA_1V8_PHY */
- regulator-name = "ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo5_reg: ldo5 {
- /* VDDA_1V8_PLL */
- regulator-name = "ldo5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo4_reg: ldo4 {
- /* VDDA_3V_USB: VDDA_USBHS33 */
- regulator-name = "ldo4";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
- };
- };
-
- tps65917_power_button {
- compatible = "ti,palmas-pwrbutton";
- interrupt-parent = <&tps65917>;
- interrupts = <1 IRQ_TYPE_NONE>;
- wakeup-source;
- ti,palmas-long-press-seconds = <6>;
- };
- };
-
- pcf_gpio_21: gpio@21 {
- compatible = "ti,pcf8575";
- reg = <0x21>;
- lines-initial-states = <0x1408>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-parent = <&gpio6>;
- interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- tlv320aic3106: tlv320aic3106@19 {
- #sound-dai-cells = <0>;
- compatible = "ti,tlv320aic3106";
- reg = <0x19>;
- adc-settle-ms = <40>;
- ai3x-micbias-vg = <1>; /* 2.0V */
- status = "okay";
-
- /* Regulators */
- AVDD-supply = <&evm_3v3>;
- IOVDD-supply = <&evm_3v3>;
- DRVDD-supply = <&evm_3v3>;
- DVDD-supply = <&aic_dvdd>;
+ regulator-allow-bypass;
};
};
-&i2c5 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins>;
- clock-frequency = <400000>;
-
- pcf_hdmi: pcf8575@26 {
- compatible = "nxp,pcf8575";
- reg = <0x26>;
- gpio-controller;
- #gpio-cells = <2>;
- /*
- * initial state is used here to keep the mdio interface
- * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
- * VIN2_S0 driven high otherwise Ethernet stops working
- * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
- */
- lines-initial-states = <0x0f2b>;
-
- p1 {
- /* vin6_sel_s0: high: VIN6, low: audio */
- gpio-hog;
- gpios = <1 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "vin6_sel_s0";
- };
- };
-};
-
-&uart1 {
- status = "okay";
- interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
- <&dra7_pmx_core 0x3e0>;
-};
-
-&elm {
- status = "okay";
-};
-
-&gpmc {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nand_default>;
- ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
- nand@0,0 {
- /* To use NAND, DIP switch SW5 must be set like so:
- * SW5.1 (NAND_SELn) = ON (LOW)
- * SW5.9 (GPMC_WPN) = OFF (HIGH)
- */
- compatible = "ti,omap2-nand";
- reg = <0 0 4>; /* device IO registers */
- interrupt-parent = <&gpmc>;
- interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
- <1 IRQ_TYPE_NONE>; /* termcount */
- ti,nand-ecc-opt = "bch8";
- ti,elm-id = <&elm>;
- nand-bus-width = <16>;
- gpmc,device-width = <2>;
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <80>;
- gpmc,cs-wr-off-ns = <80>;
- gpmc,adv-on-ns = <0>;
- gpmc,adv-rd-off-ns = <60>;
- gpmc,adv-wr-off-ns = <60>;
- gpmc,we-on-ns = <10>;
- gpmc,we-off-ns = <50>;
- gpmc,oe-on-ns = <4>;
- gpmc,oe-off-ns = <40>;
- gpmc,access-ns = <40>;
- gpmc,wr-access-ns = <80>;
- gpmc,rd-cycle-ns = <80>;
- gpmc,wr-cycle-ns = <80>;
- gpmc,bus-turnaround-ns = <0>;
- gpmc,cycle2cycle-delay-ns = <0>;
- gpmc,clk-activation-ns = <0>;
- gpmc,wr-data-mux-bus-ns = <0>;
- /* MTD partition table */
- /* All SPL-* partitions are sized to minimal length
- * which can be independently programmable. For
- * NAND flash this is equal to size of erase-block */
- #address-cells = <1>;
- #size-cells = <1>;
- partition@0 {
- label = "NAND.SPL";
- reg = <0x00000000 0x000020000>;
- };
- partition@1 {
- label = "NAND.SPL.backup1";
- reg = <0x00020000 0x00020000>;
- };
- partition@2 {
- label = "NAND.SPL.backup2";
- reg = <0x00040000 0x00020000>;
- };
- partition@3 {
- label = "NAND.SPL.backup3";
- reg = <0x00060000 0x00020000>;
- };
- partition@4 {
- label = "NAND.u-boot-spl-os";
- reg = <0x00080000 0x00040000>;
- };
- partition@5 {
- label = "NAND.u-boot";
- reg = <0x000c0000 0x00100000>;
- };
- partition@6 {
- label = "NAND.u-boot-env";
- reg = <0x001c0000 0x00020000>;
- };
- partition@7 {
- label = "NAND.u-boot-env.backup1";
- reg = <0x001e0000 0x00020000>;
- };
- partition@8 {
- label = "NAND.kernel";
- reg = <0x00200000 0x00800000>;
- };
- partition@9 {
- label = "NAND.file-system";
- reg = <0x00a00000 0x0f600000>;
- };
- };
-};
-
-&usb2_phy1 {
- phy-supply = <&ldo4_reg>;
-};
-
-&usb2_phy2 {
- phy-supply = <&ldo4_reg>;
-};
-
-&omap_dwc3_1 {
- extcon = <&extcon_usb1>;
-};
-
-&omap_dwc3_2 {
- extcon = <&extcon_usb2>;
-};
-
-&usb1 {
- dr_mode = "peripheral";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
-};
-
-&usb2 {
- dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_pins>;
-};
-
-&mmc1 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_default>;
- vmmc-supply = <&evm_3v3_sd>;
- vmmc_aux-supply = <&ldo1_reg>;
- bus-width = <4>;
- /*
- * SDCD signal is not being used here - using the fact that GPIO mode
- * is a viable alternative
- */
- cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
- max-frequency = <192000000>;
-};
-
-&mmc2 {
- /* SW5-3 in ON position */
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
-
- vmmc-supply = <&evm_3v3>;
- bus-width = <8>;
- ti,non-removable;
- max-frequency = <192000000>;
+&hdmi {
+ vdda_video-supply = <&ldo5_reg>;
};
-&dra7_pmx_core {
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
- >;
-
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15)
- >;
- };
+&pcf_gpio_21 {
+ interrupt-parent = <&gpio6>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
};
&mac {
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_default>;
- pinctrl-1 = <&cpsw_sleep>;
slaves = <1>;
mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
};
@@ -697,158 +43,3 @@
phy_id = <&davinci_mdio>, <3>;
phy-mode = "rgmii";
};
-
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_default>;
- pinctrl-1 = <&davinci_mdio_sleep>;
-};
-
-&dcan1 {
- status = "ok";
- pinctrl-names = "default", "sleep", "active";
- pinctrl-0 = <&dcan1_pins_sleep>;
- pinctrl-1 = <&dcan1_pins_sleep>;
- pinctrl-2 = <&dcan1_pins_default>;
-};
-
-&qspi {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&qspi1_pins>;
-
- spi-max-frequency = <48000000>;
- m25p80@0 {
- compatible = "s25fl256s1";
- spi-max-frequency = <48000000>;
- reg = <0>;
- spi-tx-bus-width = <1>;
- spi-rx-bus-width = <4>;
- spi-cpol;
- spi-cpha;
- #address-cells = <1>;
- #size-cells = <1>;
-
- /* MTD partition table.
- * The ROM checks the first four physical blocks
- * for a valid file to boot and the flash here is
- * 64KiB block size.
- */
- partition@0 {
- label = "QSPI.SPL";
- reg = <0x00000000 0x000010000>;
- };
- partition@1 {
- label = "QSPI.SPL.backup1";
- reg = <0x00010000 0x00010000>;
- };
- partition@2 {
- label = "QSPI.SPL.backup2";
- reg = <0x00020000 0x00010000>;
- };
- partition@3 {
- label = "QSPI.SPL.backup3";
- reg = <0x00030000 0x00010000>;
- };
- partition@4 {
- label = "QSPI.u-boot";
- reg = <0x00040000 0x00100000>;
- };
- partition@5 {
- label = "QSPI.u-boot-spl-os";
- reg = <0x00140000 0x00080000>;
- };
- partition@6 {
- label = "QSPI.u-boot-env";
- reg = <0x001c0000 0x00010000>;
- };
- partition@7 {
- label = "QSPI.u-boot-env.backup1";
- reg = <0x001d0000 0x0010000>;
- };
- partition@8 {
- label = "QSPI.kernel";
- reg = <0x001e0000 0x0800000>;
- };
- partition@9 {
- label = "QSPI.file-system";
- reg = <0x009e0000 0x01620000>;
- };
- };
-};
-
-&dss {
- status = "ok";
-
- vdda_video-supply = <&ldo5_reg>;
-};
-
-&hdmi {
- status = "ok";
- vdda-supply = <&ldo3_reg>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&tpd12s015_in>;
- };
- };
-};
-
-&atl {
- pinctrl-names = "default";
- pinctrl-0 = <&atl_pins>;
-
- assigned-clocks = <&abe_dpll_sys_clk_mux>,
- <&atl_gfclk_mux>,
- <&dpll_abe_ck>,
- <&dpll_abe_m2x2_ck>,
- <&atl_clkin2_ck>;
- assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
- assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>;
-
- status = "okay";
-
- atl2 {
- bws = <DRA7_ATL_WS_MCASP2_FSX>;
- aws = <DRA7_ATL_WS_MCASP3_FSX>;
- };
-};
-
-&mcasp3 {
- #sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins>;
- pinctrl-1 = <&mcasp3_sleep_pins>;
-
- assigned-clocks = <&mcasp3_ahclkx_mux>;
- assigned-clock-parents = <&atl_clkin2_ck>;
-
- status = "okay";
-
- op-mode = <0>; /* MCASP_IIS_MODE */
- tdm-slots = <2>;
- /* 4 serializer */
- serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
- 1 2 0 0
- >;
-};
-
-&mailbox5 {
- status = "okay";
- mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
- status = "okay";
- };
- mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
- status = "okay";
- };
-};
-
-&mailbox6 {
- status = "okay";
- mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
- status = "okay";
- };
-};
--
2.8.0.rc3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
