[PATCH v5 1/2] dt: bindings: add MARVELL's bt-sd8xxx wireless device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




From: Xinming Hu <huxm@xxxxxxxxxxx>

Add device tree binding documentation for MARVELL's bluetooth sdio
(sd8897 and sd8997) chip.

Signed-off-by: Xinming Hu <huxm@xxxxxxxxxxx>
Signed-off-by: Amitkumar Karwar <akarwar@xxxxxxxxxxx>
---
Listing changelist for both 1/2 and 2/2 here
v2: Fixed build error reported by kbuild test robot
drivers/bluetooth/btmrvl_platform.c:141:22: error:
'btmrvl_plt_pm_ops' undeclared here (not in a function)

v3: Add NULL check for 'btmrvl_plt_dev'

v4: Moved the bindings file to bindings/net/
    Corrected the name of 'name' and 'compatible' properties(Rob Herring)

v5: Comments for wlan patches were applicable here as well. Like all binding
    changes in single file, specifying node as a child of SDIO controller.
---
 Documentation/devicetree/bindings/btmrvl.txt       | 29 ------------
 .../devicetree/bindings/net/marvell-bt-sd8xxx.txt  | 55 ++++++++++++++++++++++
 2 files changed, 55 insertions(+), 29 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/btmrvl.txt
 create mode 100644 Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt

diff --git a/Documentation/devicetree/bindings/btmrvl.txt b/Documentation/devicetree/bindings/btmrvl.txt
deleted file mode 100644
index 58f964b..0000000
--- a/Documentation/devicetree/bindings/btmrvl.txt
+++ /dev/null
@@ -1,29 +0,0 @@
-btmrvl
-------
-
-Required properties:
-
-  - compatible : must be "btmrvl,cfgdata"
-
-Optional properties:
-
-  - btmrvl,cal-data : Calibration data downloaded to the device during
-		      initialization. This is an array of 28 values(u8).
-
-  - btmrvl,gpio-gap : gpio and gap (in msecs) combination to be
-		      configured.
-
-Example:
-
-GPIO pin 13 is configured as a wakeup source and GAP is set to 100 msecs
-in below example.
-
-btmrvl {
-	compatible = "btmrvl,cfgdata";
-
-	btmrvl,cal-data = /bits/ 8 <
-		0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
-		0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
-		0x00 0x00 0xf0 0x00>;
-	btmrvl,gpio-gap = <0x0d64>;
-};
diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
new file mode 100644
index 0000000..b031431
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
@@ -0,0 +1,55 @@
+Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices
+------
+
+Required properties:
+
+  - compatible : should be one of the following:
+	* "marvell,bt-sd8897"
+	* "marvell,bt-sd8997"
+
+Optional properties:
+
+  - btmrvl,cal-data : Calibration data downloaded to the device during
+		      initialization. This is an array of 28 values(u8).
+
+  - btmrvl,wakeuppin-gap : wakeup pin and gap (in msecs) combination to be
+		      configured to firmware. 'wakeuppin' is a wakeup pin number
+		      of bluetooth chip. 'gap' is a wakeup latency of a host platform.
+		      This is needed to work chip's sleep feature as expected.
+  - interrupt-parent: phandle of the parent interrupt controller
+  - interrupts : interrupt pin number to the cpu. driver will request an irq based on
+  		 this interrupt number. during system suspend, the irq will be enabled
+  		 as system wakeup source, so that the bluetooth chip can wakeup host
+  		 platform under certain condition. during system resume, the irq will
+  		 be disabled to make sure unnecessary interrupt is not received.
+
+Example:
+
+IRQ pin 119 is used as system wakeup source interrupt.
+wakeuppin 13 and gap 100ms are configured so that firmware can wakeup host
+using this device side pin and wakeup latency.
+calibration data is also available in below example.
+
+&mmc3 {
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	btmrvl: btmrvl@3 {
+		compatible = "marvell,bt-sd8897";
+		reg = <2>;
+		interrupt-parent = <&pio>;
+		interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+
+		btmrvl,cal-data = /bits/ 8 <
+			0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
+			0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
+			0x00 0x00 0xf0 0x00>;
+		btmrvl,wakeuppin-gap = <0x0d64>;
+	};
+};
+
-- 
1.8.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux