The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts | 208 ++++++++++++++++++++++
2 files changed, 209 insertions(+)
create mode 100644 arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ef39613..02505a0 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -655,6 +655,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31-i7.dtb \
sun6i-a31-m9.dtb \
sun6i-a31-mele-a1000g-quad.dtb \
+ sun6i-a31s-colorfly-e708-q1.dtb \
sun6i-a31s-cs908.dtb \
sun6i-a31s-primo81.dtb \
sun6i-a31s-sina31s.dtb \
diff --git a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts
new file mode 100644
index 0000000..e182eec
--- /dev/null
+++ b/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts
@@ -0,0 +1,208 @@
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@xxxxxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Colorfly E708 Q1 tablet";
+ compatible = "colorfly,e708-q1", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&ehci0 {
+ /* rtl8188etv wifi is connected here */
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@1000 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mma8452_int_e708_q1: mma8452_int_pin@0 {
+ allwinner,pins = "PA9";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pg";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+ vcc-pg-supply = <®_dldo2>;
+};
+
+/*
+ * FIXME for now we only support host mode and rely on u-boot to have
+ * turned on Vbus which is controlled by the axp221 pmic on the board.
+ *
+ * Once we have axp221 power-supply and vbus-usb support we should switch
+ * to fully supporting otg.
+ */
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
+ status = "okay";
+};
--
2.7.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
