Re: [linux-sunxi] [PATCH 10/11] arm64: dts: add Allwinner A64 SoC .dtsi

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi,

On 01/02/16 18:39, Andre Przywara wrote:
> The Allwinner A64 SoC is low-cost SoC with 4 ARM Cortex-A53 cores
> and the typical tablet / TV box peripherals.
> The Soc is based on the (32-bit) Allwinner H3 chip, sharing most of
> the peripherals and the memory map.
> Although the cores are proper 64-bit ones, the whole SoC is actually
> limited to 4GB (including all the supported DRAM), so we use 32-bit
> address and size cells. This has the nice feature of us being able to
> reuse the DT for 32-bit kernels as well.
> This .dtsi lists the hardware that we support so far.
> 
> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
> ---
>  Documentation/devicetree/bindings/arm/sunxi.txt   |   1 +
>  Documentation/devicetree/bindings/clock/sunxi.txt |   1 +
>  arch/arm64/boot/dts/allwinner/a64.dtsi            | 583 ++++++++++++++++++++++
>  3 files changed, 585 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/a64.dtsi
> 
> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> index 980e065..4a83853 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> @@ -14,6 +14,7 @@ using one of the following compatible strings:
>    allwinner,sun8i-a83t
>    allwinner,sun8i-h3
>    allwinner,sun9i-a80
> +  allwinner,a64
>  
>  For Allwinner SoCs without any specific needs the generic fallback value of:
>    allwinner,sunxi
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index e59f57b..44b0c6c 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -77,6 +77,7 @@ Required properties:
>  	"allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80
>  	"allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
>  	"allwinner,sun4i-a10-ve-clk" - for the Video Engine clock
> +	"allwinner,a64-bus-gates-clk" - for the A64 multi-parent bus gates clock
>  
>  Required properties for all clocks:
>  - reg : shall be the control register address for the clock.
> diff --git a/arch/arm64/boot/dts/allwinner/a64.dtsi b/arch/arm64/boot/dts/allwinner/a64.dtsi
> new file mode 100644
> index 0000000..8dce10f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/a64.dtsi
> @@ -0,0 +1,583 @@
> +/*
> + * Copyright (C) 2016 ARM Ltd.
> + * based on the Allwinner H3 dtsi:
> + *    Copyright (C) 2015 Jens Kuske <jenskuske@xxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	compatible = "allwinner,a64", "allwinner,sunxi";
> +	interrupt-parent = <&gic>;
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +	aliases {
> +		serial0 = &uart0;
> +		serial1 = &uart1;
> +		serial2 = &uart2;
> +		serial3 = &uart3;
> +		serial4 = &uart4;
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu@0 {
> +			compatible = "arm,cortex-a53", "arm,armv8";
> +			device_type = "cpu";
> +			reg = <0>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu@1 {
> +			compatible = "arm,cortex-a53", "arm,armv8";
> +			device_type = "cpu";
> +			reg = <1>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu@2 {
> +			compatible = "arm,cortex-a53", "arm,armv8";
> +			device_type = "cpu";
> +			reg = <2>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu@3 {
> +			compatible = "arm,cortex-a53", "arm,armv8";
> +			device_type = "cpu";
> +			reg = <3>;
> +			enable-method = "psci";
> +		};
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2", "arm,psci";
> +		method = "smc";
> +		cpu_suspend = <0xc4000001>;
> +		cpu_off = <0x84000002>;
> +		cpu_on = <0xc4000003>;
> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x40000000 0>;
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 13
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 14
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 11
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 10
> +			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +	};
> +
> +	clocks {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		osc24M: osc24M_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <24000000>;
> +			clock-output-names = "osc24M";
> +		};
> +
> +		osc32k: osc32k_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <32768>;
> +			clock-output-names = "osc32k";
> +		};
> +
> +		pll1: clk@01c20000 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-a23-pll1-clk";
> +			reg = <0x01c20000 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll1";
> +		};
> +
> +		pll6: clk@01c20028 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-pll6-clk";
> +			reg = <0x01c20028 0x4>;
> +			clocks = <&osc24M>;
> +			clock-output-names = "pll6", "pll6x2";
> +		};
> +
> +		pll6d2: pll6d2_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-factor-clock";
> +			clock-div = <2>;
> +			clock-mult = <1>;
> +			clocks = <&pll6 0>;
> +			clock-output-names = "pll6d2";
> +		};
> +
> +		/* dummy clock until pll6 can be reused */
> +		pll8: pll8_clk {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <1>;
> +			clock-output-names = "pll8";
> +		};
> +
> +		cpu: cpu_clk@01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-cpu-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
> +			clock-output-names = "cpu";
> +			critical-clocks = <0>;
> +		};
> +
> +		axi: axi_clk@01c20050 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-axi-clk";
> +			reg = <0x01c20050 0x4>;
> +			clocks = <&cpu>;
> +			clock-output-names = "axi";
> +		};
> +
> +		ahb1: ahb1_clk@01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun6i-a31-ahb1-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
> +			clock-output-names = "ahb1";
> +		};
> +
> +		ahb2: ahb2_clk@01c2005c {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun8i-h3-ahb2-clk";
> +			reg = <0x01c2005c 0x4>;
> +			clocks = <&ahb1>, <&pll6d2>;
> +			clock-output-names = "ahb2";
> +		};
> +
> +		apb1: apb1_clk@01c20054 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb0-clk";
> +			reg = <0x01c20054 0x4>;
> +			clocks = <&ahb1>;
> +			clock-output-names = "apb1";
> +		};
> +
> +		apb2: apb2_clk@01c20058 {
> +			#clock-cells = <0>;
> +			compatible = "allwinner,sun4i-a10-apb1-clk";
> +			reg = <0x01c20058 0x4>;
> +			clocks = <&osc32k>, <&osc24M>, <&pll6 1>, <&pll6 1>;
> +			clock-output-names = "apb2";
> +		};
> +
> +		bus_gates: clk@01c20060 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,a64-bus-gates-clk",
> +				     "allwinner,sunxi-multi-bus-gates-clk";
> +			reg = <0x01c20060 0x14>;
> +			ahb1_parent {
> +				clocks = <&ahb1>;
> +				clock-indices = <1>, <5>,
> +						<6>, <8>,
> +						<9>, <10>,
> +						<13>, <14>,
> +						<18>, <19>,
> +						<20>, <21>,
> +						<23>, <24>,
> +						<25>, <28>,
> +						<32>, <35>,
> +						<36>, <37>,
> +						<40>, <43>,
> +						<44>, <52>,
> +						<53>, <54>,
> +						<135>;
> +				clock-output-names = "bus_mipidsi", "bus_ce",
> +						"bus_dma", "bus_mmc0",
> +						"bus_mmc1", "bus_mmc2",
> +						"bus_nand", "bus_sdram",
> +						"bus_ts", "bus_hstimer",
> +						"bus_spi0", "bus_spi1",
> +						"bus_otg", "bus_otg_ehci0",
> +						"bus_ehci0", "bus_otg_ohci0",
> +						"bus_ve", "bus_lcd0",
> +						"bus_lcd1", "bus_deint",
> +						"bus_csi", "bus_hdmi",
> +						"bus_de", "bus_gpu",
> +						"bus_msgbox", "bus_spinlock",
> +						"bus_dbg";
> +			};
> +			ahb2_parent {
> +				clocks = <&ahb2>;
> +				clock-indices = <17>, <29>;
> +				clock-output-names = "bus_gmac", "bus_ohci0";
> +			};
> +			apb1_parent {
> +				clocks = <&apb1>;
> +				clock-indices = <64>, <65>,
> +						<69>, <72>,
> +						<76>, <77>,
> +						<78>;
> +				clock-output-names = "bus_codec", "bus_spdif",
> +						"bus_pio", "bus_ths",
> +						"bus_i2s0", "bus_i2s1",
> +						"bus_i2s2";
> +			};
> +			abp2_parent {
> +				clocks = <&apb2>;
> +				clock-indices = <96>, <97>,
> +						<98>, <101>,
> +						<112>, <113>,
> +						<114>, <115>,
> +						<116>;
> +				clock-output-names = "bus_i2c0", "bus_i2c1",
> +						"bus_i2c2", "bus_scr",
> +						"bus_uart0", "bus_uart1",
> +						"bus_uart2", "bus_uart3",
> +						"bus_uart4";
> +			};
> +		};
> +
> +		mmc0_clk: clk@01c20088 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";

The A64 MMC clocks don't seem to be fully compatible to A10. The output
and sample phase control has been moved to the MMC module itself.
The dividers are the same, but the additional special "outputs" are gone.

> +			reg = <0x01c20088 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;

Parents are PLL6(2x) and PLL8(2x) according to manual.

> +			clock-output-names = "mmc0",
> +					     "mmc0_output",
> +					     "mmc0_sample";
> +		};
> +
> +		mmc1_clk: clk@01c2008c {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c2008c 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc1",
> +					     "mmc1_output",
> +					     "mmc1_sample";
> +		};
> +
> +		mmc2_clk: clk@01c20090 {
> +			#clock-cells = <1>;
> +			compatible = "allwinner,sun4i-a10-mmc-clk";
> +			reg = <0x01c20090 0x4>;
> +			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> +			clock-output-names = "mmc2",
> +					     "mmc2_output",
> +					     "mmc2_sample";
> +		};
> +	};
> +
> +	regulators {
> +		reg_vcc3v3: vcc3v3 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vcc3v3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +		};
> +	};
> +
> +	soc {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		mmc0: mmc@01c0f000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c0f000 0x1000>;
> +			clocks = <&bus_gates 8>,
> +				 <&mmc0_clk 0>,

Consequently, the MMC driver now has to control the output/sample phase
with registers 0x140-0x148 instead of
> +				 <&mmc0_clk 1>,
> +				 <&mmc0_clk 2>;

And there seems to be some new clock divider somewhere which I haven't
found in the manual yet. The clock measured at the CLK pin is always
half the expected rate (even with 24MHz as MMC clock parent, so no
PLL6*2 problem).

> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb_rst 8>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc1: mmc@01c10000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c10000 0x1000>;
> +			clocks = <&bus_gates 9>,
> +				 <&mmc1_clk 0>,
> +				 <&mmc1_clk 1>,
> +				 <&mmc1_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb_rst 9>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc2: mmc@01c11000 {
> +			compatible = "allwinner,sun5i-a13-mmc";
> +			reg = <0x01c11000 0x1000>;
> +			clocks = <&bus_gates 10>,
> +				 <&mmc2_clk 0>,
> +				 <&mmc2_clk 1>,
> +				 <&mmc2_clk 2>;
> +			clock-names = "ahb",
> +				      "mmc",
> +				      "output",
> +				      "sample";
> +			resets = <&ahb_rst 10>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		pio: pinctrl@01c20800 {
> +			compatible = "allwinner,a64-pinctrl";
> +			reg = <0x01c20800 0x400>;
> +			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&bus_gates 69>;
> +			gpio-controller;
> +			#gpio-cells = <3>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +
> +			uart0_pins_a: uart0@0 {
> +				allwinner,pins = "PB8", "PB9";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart0_pins_b: uart0@1 {
> +				allwinner,pins = "PF2", "PF3";
> +				allwinner,function = "uart0";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart1_pins: uart1@0 {
> +				allwinner,pins = "PG6", "PG7", "PG8", "PG9";
> +				allwinner,function = "uart1";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart2_pins: uart2@0 {
> +				allwinner,pins = "PB0", "PB1", "PB2", "PB3";
> +				allwinner,function = "uart2";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart3_pins_a: uart3@0 {
> +				allwinner,pins = "PD0", "PD1";
> +				allwinner,function = "uart3";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart3_pins_b: uart3@1 {
> +				allwinner,pins = "PH4", "PH5", "PH6", "PH7";
> +				allwinner,function = "uart3";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			uart4_pins: uart4@0 {
> +				allwinner,pins = "PD2", "PD3", "PD4", "PD5";
> +				allwinner,function = "uart4";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_pins: mmc0@0 {
> +				allwinner,pins = "PF0", "PF1", "PF2", "PF3",
> +						 "PF4", "PF5";
> +				allwinner,function = "mmc0";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc0_default_cd_pin: mmc0_cd_pin@0 {
> +				allwinner,pins = "PF6";
> +				allwinner,function = "gpio_in";
> +				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +			};
> +
> +			mmc1_pins: mmc1@0 {
> +				allwinner,pins = "PG0", "PG1", "PG2", "PG3",
> +						 "PG4", "PG5";
> +				allwinner,function = "mmc1";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +
> +			mmc2_pins: mmc2@0 {
> +				allwinner,pins = "PC1", "PC5", "PC6", "PC8",
> +						 "PC9", "PC10";
> +				allwinner,function = "mmc2";
> +				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> +				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +			};
> +		};
> +
> +		ahb_rst: reset@01c202c0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-ahb1-reset";
> +			reg = <0x01c202c0 0xc>;
> +		};
> +
> +		apb1_rst: reset@01c202d0 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d0 0x4>;
> +		};
> +
> +		apb2_rst: reset@01c202d8 {
> +			#reset-cells = <1>;
> +			compatible = "allwinner,sun6i-a31-clock-reset";
> +			reg = <0x01c202d8 0x4>;
> +		};
> +
> +		uart0: serial@01c28000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28000 0x400>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&bus_gates 112>;
> +			resets = <&apb2_rst 16>;
> +			reset-names = "apb2";

Do we need reset-names here (and below)?

> +			status = "disabled";
> +		};
> +
> +		uart1: serial@01c28400 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28400 0x400>;
> +			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&bus_gates 113>;
> +			resets = <&apb2_rst 17>;
> +			reset-names = "apb2";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@01c28800 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28800 0x400>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&bus_gates 114>;
> +			resets = <&apb2_rst 18>;
> +			reset-names = "apb2";
> +			status = "disabled";
> +		};
> +
> +		uart3: serial@01c28c00 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c28c00 0x400>;
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&bus_gates 115>;
> +			resets = <&apb2_rst 19>;
> +			reset-names = "apb2";
> +			status = "disabled";
> +		};
> +
> +		uart4: serial@01c29000 {
> +			compatible = "snps,dw-apb-uart";
> +			reg = <0x01c29000 0x400>;
> +			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> +			reg-shift = <2>;
> +			reg-io-width = <4>;
> +			clocks = <&bus_gates 116>;
> +			resets = <&apb2_rst 20>;
> +			reset-names = "apb2";
> +			status = "disabled";
> +		};
> +
> +		rtc: rtc@01f00000 {
> +			compatible = "allwinner,sun6i-a31-rtc";
> +			reg = <0x01f00000 0x54>;
> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +	};
> +
> +	gic: interrupt-controller@{
> +		compatible = "arm,gic-400";
> +		interrupt-controller;
> +		#interrupt-cells = <3>;
> +		#address-cells = <0>;
> +
> +		reg = <0x01C81000 0x1000>,
> +		      <0x01C82000 0x2000>,
> +		      <0x01C84000 0x2000>,
> +		      <0x01C86000 0x2000>;

Maybe lowercase hex here too.

> +		interrupts = <GIC_PPI 9
> +		      (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +	};
> +};
> 

Regards,
Jens
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux