[PATCH 08/11] ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators

[Chen-Yu Tsai <wens@xxxxxxxx>]

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
---
 arch/arm/boot/dts/sun9i-a80-optimus.dts | 121 +++++++++++++++++++++++++++++++-
 1 file changed, 119 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
index 958160e40fd0..7f6bf6138966 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
@@ -161,7 +161,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
 	cd-inverted;
@@ -171,7 +171,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -204,6 +204,123 @@
 
 &r_rsb {
 	status = "okay";
+
+	axp809: pmic@3a3 {
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp809.dtsi"
+
+&reg_aldo1 {
+	/* TODO: This should be handled by the USB PHY driver */
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc33-usbh";
+};
+
+&reg_aldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pb-io-cam";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus-09-usbh";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc4 {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys-usb0-hdmi";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1425000>;
+	regulator-max-microvolt = <1575000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+	/*
+	 * The WiFi chip supports a wide range (3.0 ~ 4.8V) of voltages,
+	 * and so does this regulator (3.0 ~ 4.2V), but Allwinner SDK
+	 * always sets it to 3.3V.
+	 */
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dvdd-cam";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_eldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pm-codec-io1";
+};
+
+&reg_ldo_io0 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pg";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pa-gmac-2v5";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc-vdd1v8-io";
 };
 
 &uart0 {
-- 
2.7.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html