On Wed, Jan 20, 2016 at 02:09:19PM +0100, Lothar Waßmann wrote:
> Signed-off-by: Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
> ---
> arch/arm/boot/dts/imx53-tx53.dtsi | 40 ++++++++++++++++++++++++++++++---------
> 1 file changed, 31 insertions(+), 9 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/imx53-tx53.dtsi
> index d3e50b2..8f08389 100644
> --- a/arch/arm/boot/dts/imx53-tx53.dtsi
> +++ b/arch/arm/boot/dts/imx53-tx53.dtsi
> @@ -87,9 +87,20 @@
> regulator-max-microvolt = <3300000>;
> };
>
> - reg_can_xcvr: regulator@2 {
> + reg_3v3_etn: regulator@2 {
Why cannot this be added as regulator@5 to avoid changing every node?
> compatible = "regulator-fixed";
> reg = <2>;
> + regulator-name = "ETN 3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_etn_phy>;
> + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_can_xcvr: regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> regulator-name = "CAN XCVR";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> @@ -98,9 +109,9 @@
> gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> };
>
> - reg_usbh1_vbus: regulator@3 {
> + reg_usbh1_vbus: regulator@4 {
> compatible = "regulator-fixed";
> - reg = <3>;
> + reg = <4>;
> regulator-name = "usbh1_vbus";
> regulator-min-microvolt = <5000000>;
> regulator-max-microvolt = <5000000>;
> @@ -110,9 +121,9 @@
> enable-active-high;
> };
>
> - reg_usbotg_vbus: regulator@4 {
> + reg_usbotg_vbus: regulator@5 {
> compatible = "regulator-fixed";
> - reg = <4>;
> + reg = <5>;
> regulator-name = "usbotg_vbus";
> regulator-min-microvolt = <5000000>;
> regulator-max-microvolt = <5000000>;
> @@ -204,13 +215,20 @@
> phy-mode = "rmii";
> phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>;
> phy-handle = <&phy0>;
> + phy-supply = <®_3v3_etn>;
> mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */
> status = "okay";
>
> - phy0: ethernet-phy@0 {
> - interrupt-parent = <&gpio2>;
> - interrupts = <4>;
> - device_type = "ethernet-phy";
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-id0007.c0f1", "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <4>;
> + };
This should be a separate change.
Shawn
> };
> };
>
> @@ -309,6 +327,10 @@
> fsl,pins = <MX53_PAD_DISP0_DAT0__GPIO4_21 0xe0>; /* Flexcan XCVR enable */
> };
>
> + pinctrl_etn_phy: etn-phygrp {
> + fsl,pins = <MX53_PAD_EIM_D20__GPIO3_20 0xe0>; /* ETN PHY Power enable */
> + };
> +
> pinctrl_ds1339: ds1339grp {
> fsl,pins = <MX53_PAD_DI0_PIN4__GPIO4_20 0xe0>;
> };
> --
> 2.1.4
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
